5.51 A horizontal, circular cross-sectional jet of air having a diameter of 6 in. strikes a conical deflector as shown in Fig. P5.51. A horizontal anchoring force of 5 lb is required to hold the cone in place. Estimate the nozzle flowrate in ft/s. The magnitude of the velocity of the air remains constant. 60° FA=5 lb 6 in.

5.51 A horizontal, circular cross-sectional jet of air having a diameter of 6 in. strikes a conical deflector as shown in Fig. P5.51. A horizontal anchoring force of 5 lb is required to hold the cone in place. Estimate the nozzle flowrate in ft/s. The magnitude of the velocity of the air remains constant. 60° FA=5 lb 6 in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5.28 A circular plate having a diameter of 300 mm is held per- pendicular to an axisymmetric horizontal jet of air having a veloc- ity of 40 m/s and a diameter of 80 mm as shown in Fig. P5.28. A hole at the center of the plate results in a discharge jet of air having a velocity of 40 m/s and a diameter of 20 mm. Determine the hor- izontal component of force required to hold the plate stationary. 40 m/s 80 mm -Plate 20 mm FIGURE P5.28 40 m/s
4.4 A tank containing water is placed on a trolley, which is attached to the wall by a cable, as shown in Fig. 4.28. A pipe bend is connected to the tank through which a jet of water is coming out with a velocity of 7.5m/s. If the diameter of the nozzle is 40 mm, calculate the tension in the cable. 7.5 m/s 30% Fig. 4.28 [Ans: 61.215 N]
20 3. A 10-ft diameter by 15 ft height vertical tank is receiving water (p = 62.11b/ft3) at the rate of 300 gpm and is discharging through a 6-in ID with a constant speed of 5 fps. At a given instant, the tank is half full. Find the water level and the mass change in the tank 15 min. later
5. Consider two tanks, A and B, each with a large opening at the top. The two tanks contain different liquids. A small hole is made in the side of each tank at the same depth h below the liquid surface, but the hole in tank A has three times the cross-sectional area of the hole in tank B. (a) If it is known that the mass flow rate is the same for the two holes, find the ratio of PALPB of the densities of the liquids in tanks A and B. (b) (c) equal volume flow rates, what height above the hole must the liquid in tank A be just then? Find the ratio RVAIRVB of the volume flow rates from the two tanks. At one instant, the liquid in tank B is 90 cm above the hole. If the tanks are to have
Q1 In Fig. X6.5.3, both nozzles discharge water horizontally into the atmosphere at 30 fps. Find 0 so that the resultant force on the unit is along the axis of the 8-in-diameter pipe. 4-in-dia jet 6-in-dia jet Figure X6.5.3
3.9 For a certain stage of an axial flow turbine, the nozzle makes an angle of 28° with the wheel tangent. The axial velocity component at the inlet is 500 ft./s. (a) If the degree of reaction is 50% and the blade speed is 550 ft./s, find the blade angles. (b) If nozzle angle, blade speed, and axial velocity remain unchanged, what should the value of degree of reaction be for maximum utilization? Ans: B, = a, = 52°; ß2 =a, = 28°; R=0.145 %3D
4.3 Water jets pump (Fig. P4.3) involves a jet cross-sectional area of 0.01 m2, and a jet area associated with the jet and entrained stream is 0.075 m2. These two fluid velocity of 30 m/s. The jet is surrounded by entrained water. The total croSs sectional streams leave the pump thoroughly mixed with an average velocity of 6 m/s through a cross-sectional area of 0.075 m2. Determine the pumping rate (i.e. the entrained fluid flow rate) involved in liters/s. having shown in a dian o 6 mis Entrained water 30 mis jet Entrained water 4.9 A 4.4 An appropriate turbulent pipe flow velocitu Fig. P4.3
5.15 The flow and head requirements for a particular application are 20 cfs and 100 ft., respectively. Two identical pumps with a rated speed of 1750 rpm are an option. What would be the specific speed and the impeller diameters if the pumps are (a) connected in series and (b) if they are connected in parallel. Ans: (a) N,=3.22 (b) N,=3.22, D=1.22 ft. %3D
4.120 A rocket sled accelerates from rest on a level track with negligible air and rolling resistances. The initial mass of the sled is M, = 600 kk. The rocket initially contains 150 kk of fuel. The rocket motor kg burns fuel at constant rate m : 15 Exhaust gases leave the rocket nozzle uniformly and axially at S m Va = 2900 relative to the nozzle, and the pressure is atmospheric. Find the maximum speed reached S by the rocket sled. Calculate the maximum acceleration of the sled during the run.
Q5 (a) (b) Water flowing steadily at the rate of 0.16 m³/s is deflected downward by an angled elbow as shown in Figure Q5 (a). Given the parameter such D = 30 cm, d = 10cm, h = 50 cm, and mass of the elbow is 200 kg. Determine the force acting on the flanges of the elbow and the angle its line of the action make with the horizontal. Take the internal volume of the elbow to be 0.03 m³ and disregard the frictional effects. Water flow steadily from a tank mounted on the cart as shown in Figure Q5 (b). After the water jet leaved the nozzle tank, it falls and strikes a vane attached to another cart. The cart's wheels are frictionless and the fluid is inviscid. Determine; (i) (ii) The speed of the water leaving the tank, V₁, and the water speed leaving the cart, V2. The tension in rope A and B.
4. A 16.50 ft. diameter by 32.8 ft. height tank is receiving water (p = 62.3 lbs/ft³) at the rate of 405 GPM and is discharging through a 6.0 in. ID Line with a constant velocity of 5.36 ft/sec. At given instant the tank is half full. Find the water level and mass change in the tank 29 minutes later. Ans. 13.366 ft; 40,415 lbs.
6. An incompressible fluid flows through a nozzle at 5 kg/s. What is the final velocity if inlet velocity is 5 m/s, and the area of the exit is half the area of the inlet? 7. From #6 the fluid used is now compressible and the density at inlet is 600 kg/m3. Find the final density if exit velocity is 12 m/s?