Question 4 The window of a room is made of 5 mm thick glass which has a thermal conductivity of 1.4 W/m-K. A heater is used to maintain the room temperature at 22 °C. Take the convection heat transfer coefficients on the outer surface of the window to be 12 W/m²-K. Take appropriate assumptions while solving this problem. (a) T₂=15°C TA I L=0.005m * -A- 1m x 3m 3m², k=1.4W/m-K Figure Q2 T₂=5°C Determine the heater thermal load to maintain the room temperature?

Question 4 The window of a room is made of 5 mm thick glass which has a thermal conductivity of 1.4 W/m-K. A heater is used to maintain the room temperature at 22 °C. Take the convection heat transfer coefficients on the outer surface of the window to be 12 W/m²-K. Take appropriate assumptions while solving this problem. (a) T₂=15°C TA I L=0.005m * -A- 1m x 3m 3m², k=1.4W/m-K Figure Q2 T₂=5°C Determine the heater thermal load to maintain the room temperature?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.17P: The heat transfer rate from hot air by convection at 100C flowing over one side of a flat plate with...

See similar textbooks

Similar questions

As a designer working for a major electric appliance manufacturer, you are required to estimate the amount of fiberglass insulation packing (k = 0.035 W/m K) that is needed for a kitchen oven shown in the figure below. The fiberglass layer is to be sandwiched between a 2-mm-thick aluminum cladding plate on the outside and a 5-mm-thick stainless steel plate on the inside that forms the core of the oven. The insulation thickness is such that the outside cladding temperature does not exceed 40C when the temperature at the inside surface of the oven is 300C. Also, the air temperature in the kitchen varies from 15Cto33C, and the average heat transfer coefficient between the outer surface of the oven and air is estimated to be 12.0W/m2K. Determine the thickness of the fiberglass insulation that is required for these conditions. What would be the outer surface temperature when the inside surface of the oven is at 475C?
Show that the rate of heat conduction per unit length through a long, hollow cylinder of inner radius ri and outer radius ro, made of a material whose thermal conductivity varies linearly with temperature, is given by qkL=TiTo(rori)/kmA where Ti = temperature at the inner surface To = temperature at the outer surface A=2(rori)/ln(ro/ri)km=ko[1+k(Ti+To)/2]L=lenthofcyclinder
The heat transfer coefficient between a surface and a liquid is 57 W/(m2K). How many watts per square meter will be transferred in this system if the temperature difference is 10C?
1.10 A heat flux meter at the outer (cold) wall of a concrete building indicates that the heat loss through a wall of 10-cm thickness is . If a thermocouple at the inner surface of the wall indicates a temperature of 22°C while another at the outer surface shows 6°C, calculate the thermal conductivity of the concrete and compare your result with the value in Appendix 2, Table 11.
The heat transfer rate from hot air by convection at 100C flowing over one side of a flat plate with dimensions 0.1m0.5m is determined to be 125 W when the surface of the plate is kept at 30C. What is the average convection heat transfer coefficient between the plate and the air?
Consider a copper plate that has dimensions of 3 cm x 3 cm x 7 cm (length, width, and thickness, respectively). As shown in the following figure, the copper plate is exposed to a thermal energy source that puts out 126 J every second. The density of copper is 8,900 kg/m³. Assume there is no heat loss to the surrounding block. 126 J Copper Insulation Ⓡ What is the specific heat of copper (in J/(kg K))? J/(kg. K) What is the mass of the copper plate (in kg)? kg How much energy (in J) will be consumed during 11 seconds? J Determine the temperature rise (in K) in the plate after 11 seconds.
Ols क 1-3 A truncated cone 30 cm high is constructed of aluminum. The diameter at the top is 7.5 cm, and the diameter at the bottom is 12.5 cm. The lower surface is maintained at 93°C; the upper surface, at 540°C. The other surface is insulated. Assuming one- dimenșional heat flow, what is the rate of heat transfer in watts?
The inner and outer surface temperature of a 5.1 mm thick glass window are 17.6 and 7.1 oC, respectively. What is the heat loss in W through a window that is 1 m by 3 m on a side? The thermal conductivity of glass is 1.4 W/mK. Please keep one decimal and take positive value for the final answer.
GChoose the right answer 1. The temperature profile for steady hest conduction through a plane wall of constant thermal conductivity is a. logarithmic b. parabolic 2. A brick wall (k-0.75 W/mK ) transmits $02 of heat loss through another wall (k-0.25 W/mK, x-100 mm). If the temperature difference across both walls is the same, the thickness of the brick wall would be a.150 mm c. linear 6T b. 240 mm c. 300 mm d. 375 mm 3. The maximum temperature at the center of the solid sphere of radius R having heat generation q (W/m') is given by g'R +9R b. T, + 4k T+9R 6k d. T+9R 8k a. 2k C. 4. The internal thermal resistance of a solid can be ignored if the Biot number is less than a. 1 b. 0.5 c. 0.1 d. Fourier number 5. The ratio of heat transfer of a fin to the heat transfer without fin is referred to as a. fin resistance b. fin efficieney efin effectiveness d. fin conductance.
FIll in the blanks: A slab 0.25 m thick with thermal conductivity of 45 W/m-K receives heat from a furnace at 500 K both by convection and radiation. The convection coefficient has a value of 50 W/m²- K. The surface temperature is 400 K on this side. The heat is transferred to surroundings at T, both by convection and radiation. The convection coefficient on this side is 60 W/m2-K. Determine the surrounding temperature. K.
The compartment below is used as a freezer of refrigerator compartment. Inner wall is at -10 C and outer wall is at 20 C. Insulator with a thermal conductivity of 0.040 W/(mK) is used to prevent the heat losses from the compartment. The shape is in square form with a side of 1.3 m and unit width into the page. Determine the amount of the heat load if the thickness of the insulator is 2 cm? *
Q: A large plane wall of thickness (L= 0.3 m), thermal conductivity (k = 40 W/m-°C), and surface area 0.4 m2. The left side of the wall is maintained at a constant temperature of 70°C while the right side loses heat to the surrounding air with heat flux q' expressed by: 1200k q = k+20L A- Find a relation to determine the variation of temperature in the wall. B- Determine the rate of heat transfer through the wall. C- Determine the temperature at the right side of the wall. wall T1= 70 °C L= 0.3m