5. As shown in the diagram, P= 10 kN. F =5 kN. (1) Detemine the force in member BC and the reactions at A. (2) Assume that the area of cross section of BC is 100 mm?, detemine the stress on cross section of BC. (3) Assume that the allowable stress [0]=50MPA, determine the minimum area of cross section of BC. | C A 30° В E 2m 1m 1m F

5. As shown in the diagram, P= 10 kN. F =5 kN. (1) Detemine the force in member BC and the reactions at A. (2) Assume that the area of cross section of BC is 100 mm?, detemine the stress on cross section of BC. (3) Assume that the allowable stress [0]=50MPA, determine the minimum area of cross section of BC. | C A 30° В E 2m 1m 1m F

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

QUESTION 2 The rigid bar ACE is supported by two steel rods AB and CD (Esteel = 200 GPa) with the cross sectional areas of each rod is given as shown in Figure Q2. (a) Determine the position d of the 30 kN load so that the average normal stress in each rod is the same. (b) Find the strain in rod CD, ɛcD (c) Determine the horizontal displacement of point E 1.2 m ACD = 600 mm? 0.8 m E 30 kN AAB = 900 mm2 d B 1.8 m Figure Q2
When an axial load is applied to the ends of the bar shown in the figure, the total elongation of the bar between joints A and C is 0.17 in. In segment (2), the normal strain is measured as 1,450 uin./in. Assume L₁ - 45 in. and L₂ - 94 in. Determine (a) the elongation of segment (2). (b) the normal strain in segment (1) of the bar. P A Answers: L₁ (a) in.₂ = i (b) £₁ = i B (2) L2 in. uin./in.
Members BC and DE are 50 mm wide and 16 mm thick and made of steel (E = 200 GPa). Member AF is rigid. For a load of P = 60 kN, determine 500 mm (a) the normal stress in member BC, В C (b) the normal stress in member DE, 250 mm E (c) the displacement of point A. D Assume BC and DE do not yield or buckle. 250 mm F 500 mm- 650 mm
For the steel plate with the plane stress state shown. If E = 200 GPa, v = 0.3 and a=12 10 C. if this steel plate was heated from 25 C to 150 c. Find the normal strain in x direction (E). Select one: -3 O a. 4.06*10 -3 O b. 2.03*10 O c. NONE -3 O d. -4.06*10 -3 O e. -2.03*10
The two bars shown in the figure are used to support a load P. When unloaded, joint B has coordinates (0, 0). After load P is applied. joint B moves to the coordinate position (0.40 in., -0.55 in.). Assume a - 10 ft, b-7 ft, and h-8 ft. Determine the normal strain in each bar. Answers: EAB Egc i i B P b με με
The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 11 mm². The cross-sectional area of rod (2) is 15 mm². For a uniformly distributed load of w = 3.2 kN/m, determine the length a so that the normal stress is the same in each rod. Assume L = 5.60 m. A (1) B Answer: a = i L a D (2) m
When an axial load is applied to the ends of the bar shown in the figure, the total elongation of the bar between joints A and C is 0.15 in. In segment (2), the normal strain is measured as 1,450 uin./in. Assume L₁ = 44 in. and L₂ = 82 in. Determine (a) the elongation of segment (2). (b) the normal strain in segment (1) of the bar. (1) P L₁ B (2) L2
The rigid beam ABC is supported by a pin connection at C and by steel rod (1), which has a diameter of 12 mm. If the normal stress in rod (1) must not exceed 225 MPa, what is the maximum uniformly distributed load w that may be applied to beam ABC? Use dimensions of a = 350 mm, b = 700 mm, and c = 525.0 mm. Dot A Answer: W = ↓↓ a i 1 B W b (1) ↓↓ kN/m &
hand written plz B Shown in the figures (1) and (2) are trusses containing members that are made of same materials (Modulus of Elasticity E) and with same cross-sectional area A. When the load P is applied, which of the following statement about the strain energy of the entire system is CORRECT? Strain energy U(1) > U(2) Strain energy U(1) < U(2) Strain energy U(1) = U(2) Impossible to determine 30° (1) ic 30° D (2) ic
IV. Question 4 Two aluminium strips and steel strip are to be bonded together to form a composite member of width b and height h (Figure 5). The modulus of elasticity is 200 GPa for the steel and 75 GPa for the aluminium. Knowing that moment M is apply on the structure as shown in Figure 5, estimate the maximum stress in the aluminium and steel for the value of a from 0 to 20 mm using 2.5 mm increments. Note that you need to choose the suitable value of b, h, and M Length b M h Front View Side View Surface