4. A steel bar of 40 mm × 40 mm square cross-section is subjected to an axial compressive load of 200 kN. If the length of the bar is 2m andE = 200 GPa, the elongation of the bar will be: (A) 1.25 mnm (B) 2.70 mm (C) 4.05 mm (D) 5.40 mm

4. A steel bar of 40 mm × 40 mm square cross-section is subjected to an axial compressive load of 200 kN. If the length of the bar is 2m andE = 200 GPa, the elongation of the bar will be: (A) 1.25 mnm (B) 2.70 mm (C) 4.05 mm (D) 5.40 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A rod is composed of copper and steel section rigidly bolted in the wall as shown in the figure. If an axial load of F= 300 N and the cross sectional area of the rod is 200 mm² , determine the stress in the section of copper. ... Copper Steel 2F F 3m 2m (A) 4.5 MPa (B 0.75 MPa C) 3.0 MPa D) 1.5 MPa
A rectangular bar of length L has a slot in the central half of its length. The bar has width b, thickness t, and elastic modulus E. The slot has width b/3. The overall length of the bar is L = 520 mm, and the elastic modulus of the material is 74 GPa. If the average normal stress in the central portion of the bar is 190 MPa, calculate the overall elongation of the bar. Answer: 6 = b IN -1/2- b 6/3 mm
Rigid bar ABC is supported by bronze rod (1) and aluminum rod (2), as shown. A concentrated load P is applied to the free end of aluminum rod (3). Bronze rod (1) has an elastic modulus of E₁ = 15,000 ksi and a diameter of d₁ = 0.60 in. Aluminum rod (2) has an elastic modulus of E₂ = 10,000 ksi and a diameter of d₂ = 0.75in. Aluminum rod (3) has a diameter of d3 = 1.00in. The yield strength of the bronze is 48 ksi and the yield strength of the aluminum is 40 ksi. Assume a = 2.5 ft, b = 1.5 ft, L₁= 6 ft, L₂ = 8 ft, and L3 = 3 ft. (a) Determine the magnitude of load P that can safely be applied to the structure if a minimum factor of safety of 1.8 is required. (b) Determine the deflection of point D for the load determined in part (a). (c) The pin used at B has an ultimate shear strength of 60 ksi. If a factor of safety of 3.3 is required for this double shear pin connection, determine the minimum pin diameter that can be used at B. ī Bronze (1) L A a B Aluminum (3) D Aluminum (2) b P L3…
The rigid bar AB, attached to two vertical rods as shown in Fig. is horizontal before the load P is applied. Determine the maximum value for P If the stress must not exceed: 160 MPa for steel and 80 MPa for Bronze. Then determine the vertical movement of P. BRONZE L-5 m A=500 mm STEEL L-4 m A-400 mm E=80 GPa E-200 GPa 3 m 5 m P.
The cross-sectional area of the bar is 5 cm². Use E = 70 GPa for aluminum, and E = 200 GPa for steel. L. Aluminum Steel Aluminum 80 kN 20 kN - 30 kN + 70 kN A D B - 3 m - - 4 m · 5 m
2. Two steel cables support an applied load of 100 kN as shown in the figure below. Determine the following: a. The deformation of member AC and member BC. b. The vertical and horizontal displacement of point C. A A = 75 sq. mm L = 3 m E = 200 GPa 22° C 45° 18° A = 75 sq. mm В L = 3 m 100 kN E = 200 GPa %3D
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. P = 10 kN a. What is the stress (MPa) in the Bronze material? b. What is the stress in Aluminum in MPa? c. What is the stress in Steel in MPa?
Calculate the smallest area of each cable if the stress is not to exceed 76 000 KPa in bronze and 118 MPa in steel if a homogeneous 778 000 g bar AB is supported at either end by a cable.
just final answer A rigid component ABC is supported by a pin-connected member (1). The member has a rectangular cross-section with dimensions of 54 mm and 48 mm. The elasticity modulus of the material is 169 GPa. If L1=2421 mm, L2=1226 mm, L3=2272 mm, and L4=2072 mm; Determine the maximum normal stress (MPa) in member (1) without buckling.
A steel bar with dimensions and cross section shown is suspended vertically. Three concentric downward loads are applied to the bar: 22 250N at the lower end; 13 500 N at 0.35m above the lower end, and 9000N at 1m above the lower end. The modulus of elasticity of the steel is 210GPa. What is the total change in length of the bar?
3) At room temperature (20 °C) a 0.8 mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 120 °C, determine (a) the normal stress in the aluminum rod, (b) the change in length of the aluminum rod Bronze: Aluminum: Steel: Area: 1000 mm2 Area: 2000 mm2 Area: 1500 mm2 a = 18.4 x 10-6 E = 103 GPa a = 23.6x 10-6 E = 75 GPa a = 17.3 x 10-6 E = 190 GPa %3D %3D 0.8 mm 100 mm 150 mm 300 mm Bronze Al Steel
Determine of the internal resistance force of each segment of the bar shown below, and the total elongation of the bar. Let: The forces acting P₁=150kN, P₂=250kN, P3=200kN, P4=50KN. Areas of the bar segments A1=1000mm, A2=2000mm, A3=1000mm. E=200Gpa -2000 mm -1000- ** -1500 P₂ 1b P3 P4 P₁ A₁ la a B A₂ b C A3 C C D