450 N AB = 450 N compression %3D 30 AC = 389.71 N tension BC = 450 N tension BD = 900 N compression CD = 389.71 N tension 30 30 450 N

Q: 1. Problem Solving: Solve the following situations as completely as possible, use any method that…

A: P= 250 KN W= -7x+81 KN/m Note According to the company guidelines i am able to answer only first…

Q: A simply supported beam made of five 50mm x 200mm blocks of wood carries the load as shown in the…

A: From the given question it is required to calculate allowable pitch of the bolt if each bolt can…

Q: Given: F |Change in length of CF=0.00208a mm Area(BE)=150a mm? E Area(CF)=150a mm? 18a mm E E=200…

A: When the load is acting on the body or specimen there is some deformation or change in the dimension…

Q: Wo> pa WIOX 30 18' Find: Centerline spacing = a if p: .6 V : 18 Ksi

A:

Q: A P Front view -160 mm B D 18 mm 120 mm

A: Load P = 4kips applied at the free end of the mechanism . BD bar is reactangular bar of thickness =…

Q: Situation 1: The 300-lb force is to be resolved into components along lines a-a' and b-b'. a 300 lb…

A: Given data in question  Load Angle To find out  Components

Q: Refer the beam shown with cross section of thickness, t = 15 mm. If F = 84 kN and a = 150 mm, F 2a…

A: All options are incorrect

Q: Where it get the value 2 and 10 for the green circle? Please expl

A: This question is related to the Design concrete structures.In this question ask about the , Where it…

Q: Propose the cross-section for the beam. Draw the cross section (assume reasonable dimensions) of the…

A:

Q: the centroid of the area shown. In part (b), note the sym- nifying that the area is symmetric about…

A:

Q: Situation 2: Four 100mm x 100mm x10mm angles are latticed together to form the 12m column section..…

A:

Q: a. h the gven fgure below, the bearing of line AB is N 82 33' E. Determine the bearing of the bther…

A: Bearing of a line can be defined as its inclination from the North pole or south pole depending upon…

Q: For the beam l-section below, calculate the second moment of area about its centroidal x-axis…

A:

Q: What is the vertical displacement at Joint A in mm? I=15.5 x 10 mm and E 200 GPa Seg Origin Limit AB…

A:

Q: For the given properties of the beam below, determine the safest wy that the beam will carry. bf =…

A:

Q: Solve " Example 5 - Head and One-dimensional Flow II" but assuming that line AE has a downward slope…

A: Given data: Area=10 cm2 Given scale=2H:1V length of St. line=10m Required length=11.18m

Q: Please answe

A:

Q: 535 250 !! A23. The area of the shaded section shown in Fig. P-A23 is 40 X 103 mm?. If I,, X 10°…

A: Find moment of inertia about X2 axis?

Q: 1. From the given figure shown below, determine the centroidal moment of Inertia (Ixo and lyo) of…

A:

Q: Express e ach of the forces in Cartesian vector form etermine the magnitude and coordinate direction…

A:

Q: Please answer the following and fill up the table using Principle of virtual work method only.…

A: A beam is loaded is as followsdeflection at joint A has tobe found out

Q: Draw a shear diagram

A:

Q: H Y G 30 kips - 20 30 kips C 40 kips 40 kips 40 kips 50 kips 70 kips

A:

Q: Show that the function f(x, y, z) = e3x+4y.cos(5z) satisfy 32f a2f + əx² Əy² 82f = 0 3z² 02f 02f 02f…

A:

Q: Problem #02: Analyze the given frame using flexibility matrix method. Take Ax and Ay as redundant…

A:

Q: Q2 All members of the truss in Figure Q2 are to be fabricated from the same stock of thin-walled,…

A:

Q: Q1: Draw shear force and bending moment diagrams by using section method. 20 kap 4 kip t Hinge Q2:…

A:

Q: A 100m tape is 100m long at 15 kg, at 25 kg tension it is used to measure the length of the line.…

A:

Q: ΕΧΑMPLΕ 1) A circular bar having 200 mm? area is subjected to axial loads as shown in Fig „Find the…

A:

Q: ENGINEERING MECHANICS

A:

Matrix Algebra for Structural analysis

Structural analysis is a process in which the effects of different loads and internal forces, acting on structures and their elements are determined. This method of analysis is effective in detecting the failure loads of the structural elements and the design can be altered before commencing the construction process, which ensures proper strength and safety of the structures.