Please answer the following and fill up the table using Principle of virtual work method only. Please draw an fbd on the real beam & virtual beam. Formulas are provided in the other picture used as guide. Thanks FOR DISPLACEMENTReal Loadsmmin.inVirtual loadsIxA=r²mMJo El-dxAFOR ROTATION/SLOPEReal Loadsរនី។Virtual loads1x8 =pmomETdxWhere1 = external virtual unit load acting on the beam in the stated direction of A.m = internal virtual moment in the beam/frame, expressed as a f(x) and caused by the external virtualunit load.A = external displacement of the point caused by the real loads acting on the beam/frame.M = internal moment in the beam/frame, expressed as f(x) and caused by real loads.E = modulus of elasticityI = moment of inertia of the CSA about the neutral axis What is the vertical displacement at Joint A in mm?I=15.5 x 10 mm¹ and E= 200 GPaSeg Origin LimitAB A 0-2BC A 2-5CDA 5-6fox 9 kN-m33 kN/mM-2m2kN/m-3 m-+-1m-mMELdx (mm)

A beam is loaded is as followsdeflection at joint A has tobe found out

Please answer the following and fill up the table using Principle of virtual work method only. Please draw an fbd on the real beam & virtual beam. Formulas are provided in the other picture used as guide. Thanks

Please answer the following and fill up the table using Principle of virtual work method only. Please draw an fbd on the real beam & virtual beam. Formulas are provided in the other picture used as guide. Thanks

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: a. Setup menu b.Geometry menu b. General menu c. De

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: Determine the location of the centroid C (x, y) of the beam's cross-sectional area and then compute…

A: all units are in mmif you have any doubts please comment

Q: 4X-Y -2x+6y+Z =9 - X tY t7z =-6 17: 11

A: Solution: We have to solve the given system of equation using Jacobi iteration.

Q: What is the Maximum moment in kN-m. Given: w = 48, a = 5, b = 4, and c = 1. w kN/m B. a m b m cm RA…

Q: For the figure shown, a. Determine the location of the centroid measured from the bottom (y). b.…

A: Fig-1Rectangle:Base=75+30=105mmHeight=25+30=55mmx1=1052y1=552-30=-2.5Fig-2Quarter…

Q: draw the 3D bending stress distribution for your releva

Q: Problem 2: Using any method, find the ff. when E and I 100 GPa 100x10^6 mm^4 Location and magnitude…

Q: For the Beams Shown below solve each of the Following: Deflection at Points B C and D for the…

Q: 5 in. 3 in. 3 in. i 4 in. amicarner

Q: Given the angle of rotation is small and the materials remain linear elastic, which statement below…

A: Objective: To choose the incorrect statement corresponding to the twisting of circular shafts.…

Q: Use the method of virtual work and horizontal displacement of joint C 600 N 2 m 000 N E 2 m B 2 m

Q: for problems 13.1 through 13.6 use the virtual-work method to deteermine the deflection of each of…

A: Given:E=29 x 106 psiE=29 x 103 kipsin2To determine:Vertical deflection at each jointsNote: Please…

Q: Find the static and kinematic indeterminacy respectively for the given frame shown below: C D E K H…

A: For given arrangement, The static and kinematic indeterminacy

Q: Determine the centroid of the beam's cross-sectional area and then compute the moment of inertia…

Q: 80mm 400 mm %3 40mm 350mm 40mm

Q: Please use geometry instead of sin & cos when solving. Find Ax,Ay,Bx,By,Cx,Cy

Q: 1. Determine the centroid and moment of inertia along x-axis of the given American standard…

Q: The cantilever beam shown in the figure consists of a rectangular structural steel tube shape [E =…

A: Given:E=200 GPaI=95×106 mm4PB=20 KNPC=53 KNwAB=61 KN/mwBC=19 KN/mL1=1.6 mL2=3.3 mNow,Using the…

Q: Using MOMENT-AREA Method for deflection analyze the beam below 25KN 10KN/m A El=120000KNM^2…

Q: The beam cross sections shown are symmetric about the x and y axes. Determine the area moments of…

A: Given data,beam cross section is given top flange width =140mmheight=250 mmthickness of web =6…

Q: Use the virtual work method to determine the slope and deflection at point B of the beam shown

A: In the virtual work method to determine the slope and deflection at a point, we have to introduce…

Q: concentrated load of 8 kN at a distance of 3m from the right support. E = %3D 200 GPa and I =…

A: Double integration method Given simply support beam Span l = 12m Find Max deflection Max deflection…

Q: What are the differences between the true kinematic and pseudokinematic methods?

A: the kinematic method requires an initilisation process at the beginning of the survey in order to…

Q: The maximum deflection for the cantilever beam below is more than 0.03m.Use Macaulay’s method of…

Q: 7 in. 9.9 in. 14 in. 7 in. 14 in. 16 in.

A: Given:- the wire shown, composed of 4 sections.

Q: A P Front view -160 mm B D 18 mm 120 mm

A: Load P = 4kips applied at the free end of the mechanism . BD bar is reactangular bar of thickness =…

Q: What is the static indeterminacy of the 2D frame given below? Hinge

A: The frame has fixed support at Bottom end . Each end has total number of 3 reaction . Their are 4…

Q: For the beam shown in Fig.Q4, use the principle of virtual work to determine (1) the vertical…

A: Given Point force(P)=35KN Uniformly distributed load(q)=14 kN/m Length of AB span (L)=4 m Length of…

Q: What is the degree of static indeterminacy for the beam shown in Figure?

A: The given question is related with structural analysis . In this question we are provided with value…

Q: 50KN A 20 KN K-5m----5m-- QUESTION: FIND DEFLECTION AT MIDSPAN. B

A: The given beam is a simply supported beam and is statically determinate beam. The deflection at the…

Q: 1. Draw the free-body diagram of cach object.

A: Draw the free body diagram of cache object.

Q: Use virtual work method Length ab is 10m bc 10m cd 10m de 10m ef 10m Find Deflection at A B C D E…

A: As per bartleby guidelines, only 1st question need to be solved among multiple questions posted.…

Q: Calculate the Midspan Deflection of the Beam using Double Integration Method (Macaulay's METHOD…

A: Calculation of Mid Span Deflection using Macaulay Method

Q: Determine the location of the centroid C (x, y) of the beam's cross-sectional area and then compute…

Q: Use virtual work to find the vertical.displacement under the 30 kN load and the rotation at c. 20 kN…

Q: For the simple beam shown, use the virtual work method to find (a) the location and value of the…

A: using Virtual work method## Calculation of location and value of maxm Rotation and maxm Deflection…

Question

FOR DISPLACEMENT
Real Loads
mmin.in
Virtual loads
IxA=
r²mM
Jo El
-dx
A
FOR ROTATION/SLOPE
Real Loads
រនី។
Virtual loads
1x8 =
pmom
ET
dx
Where
1 = external virtual unit load acting on the beam in the stated direction of A.
m = internal virtual moment in the beam/frame, expressed as a f(x) and caused by the external virtual
unit load.
A = external displacement of the point caused by the real loads acting on the beam/frame.
M = internal moment in the beam/frame, expressed as f(x) and caused by real loads.
E = modulus of elasticity
I = moment of inertia of the CSA about the neutral axis

What is the vertical displacement at Joint A in mm?
I=15.5 x 10 mm¹ and E= 200 GPa
Seg Origin Limit
AB A 0-2
BC A 2-5
CD
A 5-6
fox 9 kN-m
33 kN/m
M
-2m
2kN/m
-3 m-
+-1m-
mM
EL
dx (mm)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: calculate reactions at B&C

VIEW

Step 3: applying unit load at joint A

VIEW

Step 4: calculate deflection at A

VIEW

Solution

VIEW

Step by step

Solved in 5 steps with 16 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

PLEASE PROVIDE COMPLETE SOLUTIONNEED ASAP INSTANT UPVOTE
A simply supported beam with a span of 12m is subjected to a concentrated load of 8 kN at a distance of 3m from the right support. E = %3D 200 GPa and I = 60x10^6 mm^4. Determine the location of the maximum deflection (please submit your solution for this item using DIM)
can you please draw the bending moment diagram too
Civil Engineering Old MathJax webview | | EI, EA=const Determine the axial force of the diagonal member BD, using the deflection angel method. What information should I add?
Which procedure provides a method that may be used to determine the displacement and slope at a point on the elastic curve of a beam, using the method of virtual forces?
Use CONJUGATE BEAM METHOD to Determine the following: (a) slope at A (b) deflection at midspan on the beam shown The beam is a wide flange and has a modulus of elasticity of 200 GPa. Use the table provided for the dimensions of the section. 18 kN 48 kN/m B S130 X 15 1m Flange Web Thick- Thick- Depth Width A, mm? d, mm br, mm Area ness ness Designationt tr, mm tw, mm S130 × 15 1890 127 76.2 8.28 5.44
Hello, Could please explain how to calculate deflection regarding the frames in the image attached, Thank you
Calculate the total static indeterminacy of the plane frame shown in the figure below Exlain in detail and clearly
please write out the solution the formatting does not work when it is typed. Thank you
Solve for the shape factor of the section shown below TT 630mm 25mm 380mm 25mm 25mm 315mm.
Define Load versus deflection plot and also show it diagrammatically.
Solve for the smallest moment of inertia I of the beam so that its maximum deflection does not exceed the limit of 1/360 of the span length (L/360). E= 200GPa Choices: a) 5256(10^6)mm^4 b) 6552(10^6)mm^4 c) 6255(10^6)mm^4 d) 5625(10^6)mm^4