A structural T-section is formed by connecting a 150 mm x 40 mm steel plate with a 80 mmx 40 mm steel plate as show in the diagram. For the combined section calculate:150 mm40 mmA40 mm80 mmSSESSMa. the location "e" of the principal (centroid) X-axis (relative to the top edgeof the section). "cb. the second moments of area Ixx and Ivy about the principal X- and Y-axes.

150 mm x 40 mm steel plate 80 mm x40 mm steel plate

A structural T-section is formed by connecting a 150 mm x 40 mm steel plate with a 80 mm x 40 mm steel plate as show in the diagram. For the combined section calculate: 150 mm 40 mm SSM 40 mm 80 mm a. the location "e" of the principal (centroid) X-axis (relative to the top edge of the section). "c b. the second moments of area Ixx and Ivy about the principal X- and Y-axes.

A structural T-section is formed by connecting a 150 mm x 40 mm steel plate with a 80 mm x 40 mm steel plate as show in the diagram. For the combined section calculate: 150 mm 40 mm SSM 40 mm 80 mm a. the location "e" of the principal (centroid) X-axis (relative to the top edge of the section). "c b. the second moments of area Ixx and Ivy about the principal X- and Y-axes.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel beam is subjected to a uniform load with length of 8m. Assume that the beam is simply supported. Use Fy= 248 Mpa. Properties of W-shape beam d=229 mm bf=210 mm rf=23.7 mm Tu-14.50 mm kdes=33. 80mm ry=53.80 mm Ix=113 x 10^6 mm^4 Iy-36.9 x 10^6 mm^4 Sx-990 x 10^3 mm^3 Zx 1150 x 10^3 mm^3 J-2100 x 10^3 mm^4 Cu-387 x 10^9 mm^6 What is the nominal shear strength capacity of the section (in kN)?
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
The Figure below shows a two-member truss supporting a block of weight W. The cross-sectional areas of the members are 800 mm² for AB and 400 mm² for AC. Determine the maximum safe value of W (kN) if the working stresses are 110 MPa for AB and 120 MPa for AC. ... B 40 deg. A 60 deg. A) 38.90 в) 55.30 61.70 76.2
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h= 430 mm tw= 12 mm d= 110 mm t= 9.6 mm Additionallv: • The area of each pipe is A = 3028 mm2. • The moment of inertia of the entire beam cross section about the z centroidal axis is I>= 320410000 mm4. If the beam will be subiected to a shear force of V = 110 kN, determine the shear stress at point K, located at yK = 70 mm below the z centroidal axis.
The thin rectangular plate is subjected to the four forces shown. Determine the equivalent force-couple system at O. Is R perpendicular to Mo? 270 N 0.40 m 1.24 m y 270 N 270 N 29° 270 N Answer: Force-couple system R= ( i+ 130.899 j+ i -236.147 k) N Mo = ( i 506.147 i+ i j+ i k) N-m
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 430 mm t₁ = 14mm d = 110 mm t = 9.6 mm Additionally: • The area of each pipe is A = 3028 mm². • The moment of inertia of the entire beam cross section about the z centroidal axis is lz= 325870000 mm². If the beam will be subjected to a shear force of V=245 kN, determine the shear stress at point H, located at y = 110 mm above the z centroidal axis. d H.V Answer: TH= x Z MPa Уи YK H K
An axial member consisting of two polymer bars is supported at C as shown. Bar (1) has a cross-sectional area of 680 mm² and an elastic modulus of 29 GPa. Bar (2) has a cross-sectional area of 1580 mm² and an elastic modulus of 15.2 GPa. Determine the deflection of point A relative to support C. 70 KN 0.85 m O -1.902 mm O-2.101 mm O -2.250 mm O-1.354 mm O -2.879 mm 90 kN (1) 90 kN B (2) 1.15 m
365 For a 200 mm x 200 mm beam shown below with E = 20 GPa, select in the choices %3D the value that most nearly gives the following; Use Conjugate Beam Method 25.50 Reaction at D in kN [ Select ] Deflection at B in mm [ Select ] Deflection at C in mm 19 kN/m 5 kN/m BI 4.2 m 3 m - -3.6 m B & C are int. hinge %23 to search acer
The force in DB of the truss shown in below figure is C 5m 2W 5m E W A B. D. 5 W tension O VW tension O 2W compression O v3 W compression
The steel truss with E=200GPais loaded as shown in the figure. Determine the following: the following a) the deformation of member AB if the cross-sectional area is 2500mmb) the deformation of member AD if the cross-sectional area is 1800mm A 4.0m 200 KN B D 4.0m 1² 2.5m
A horizontal beam AD is supported by an inclined strut BC carries a load W = 2.4KN at the position shown. The strut, which consist of one bar is connected to the beam by a bolt passing through the three bars meeting at joint C. BC is 75mm wide x 10mm thick strut while AD is 100mm wide by 10mm thick rigid bar. a. Determine the required bolt diameter at A if the allowable bolt shear stress is 68MPA, assuming single shear. b. Determine the total vertical displacement at D if E = 200,000MPa A C 10 10 1.2 B Joint at C 1.2 1.2
Compute the deformation of the beam using conjugate method E= 200 GPa I= 1000 x 106 mm4