Please answer the question number 4. Show the complete solution. Thank you. 3. A small drop of water at 80° F is in contact with the air and has a diameter of 0.0200 in. If thepressure within the droplet is 0.082 psi greater than the atmosphere, what is the value of the surfacetension?Answer: 0.00492 lb/ft4. Helium at 149 kPa absolute and 10°C is isentropicallyl compressed to one-fourth of its originalvolume. What is its final pressure?Answer: 1488 kPasbs (Use: k = 1.66)

Answer 4: Given data: P1=149 kPaT1=10°CV2=14V1 Need to determine the final pressure.

Answered: 4. Helium at 149 kPa absolute and 10°C…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

ıf u solve this Can u solve full please Define the following: Mechanical properties of materials: Strength of material: Ultimate strength: Yield strength: Ductility: Toughness: ıf u solve this Can u solve full please
Choose the correct answer below and show your solution completely. Make sure that your finals answer is 4 decimal places.
Could you please spreate each question alone because there are two questions
Completely solve and provide the diagram. Box the final answer. Write legibly 2. Water cooled steam condenser receives exhaust from multi-stage turbine at saturation temperature of 40°C. Cooling water is available at 20° at the inlet condition and temperature of water leaving the condenser is at 28°C. What is the LMTD?
The attached answer was provided for the attached question. The equation uses the given temperature in celcius and the answer is also given in celcius. The temperature was used in the equation without converting from F and the answer was supposed to be in F. I am worried that even if I converted the answer to celcius that it would be correct because temperature was used in the equation using the incorrect unit.
Please do the last three questions (2, 3 and 4)! Thank you in advance! A seesaw that weights 45lbs and its 5m long is balanced on the fulcrum in the center. 1- Two children are sitting on opposite sides of each other on the seesaw. One child weights 50lbs and is sitting 0.7m on the left end. Where should the other child sit in order to be balanced on the seesaw if they weigh 42lbs? 2- Now, a third child wants to sit on the seesaw and weighs 30lbs and is sitting 1.25m in front of them and is closer to the fulcrum on the right side. What are the CW and CCW moment of the seesaw now? What is the net moment and direction? 3- Then, a fourth child wants to play on the seesaw and is on the left side of the plank in order to bring the system to equilibrium. How much does the child weigh (Calculate the pounds of force needed in order for rebalance?) 4- Now the fourth child leaves the other three children sitting on the plank. If the three children are sitting in the same potions as they did…
Typewritten for an upvote. No upvote for handwritten. Please skip if you have already done this. Thank you
PLEASE DO THIS TYPEWRITTEN AND COMPLETE IT, I WILL UPVOTE. IF NOT COMPLETE AND TYPEWRITTEN, NO UPVOTE. THANK YOU
Need help answering these questions.
PROBLEM 3: POWER AND EFFICIENCY PLEASE HELP ME WITH MY ASSIGNMENT - Solve the problems on a clean sheet of paper. Follow the Given-Required-Analysis-Solution-Summary of Answers format. Make sure to include all pertinent solutions. - Round your final answers to three (3) decimal places. For example, if you calculated an answer to be “9.80665” it should be expressed as “9.807”. At the instant shown, point P on the cable has a velocity vp = 12 m/s which is increasing at a rate of ap=6m/s2. Determine the power input of motor M at this instant if it operates with an efficiency of 0.8. The mass of block A is 50 kg.
Choose the correct answer below and show your solution completely. Make sure that your finals answer is 4 decimal places.

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

4. Helium at 149 kPa absolute and 10°C is isentropically compressed to one-fourth of its original volume. What is its final pressure? Answer: 1488 kPasb: (Use: k= 1.66)