4) A FOUR screw lifting mechanism (Similar to awesome, mind-boggling, most beautiful CAD video shown on the youtube link enclosed) is used to lift a load of 115,000 lb. (a) Identify the size of a standard Acme thread from the data table. (b) Identify the theoretical Horsepower of the motor if the platform is moving at 6 inches per second.

4) A FOUR screw lifting mechanism (Similar to awesome, mind-boggling, most beautiful CAD video shown on the youtube link enclosed) is used to lift a load of 115,000 lb. (a) Identify the size of a standard Acme thread from the data table. (b) Identify the theoretical Horsepower of the motor if the platform is moving at 6 inches per second.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter18: Application Of Motors

Section: Chapter Questions

Problem 21RQ: A belt-driven blower assembly is equipped with a motor that turns a 5-in. drive pulley at a speed of...

See similar textbooks

Similar questions

Hello, I hope you can help me. I'm trying to create a device that has a spinning axle and I need to change the rotational force to be perpendicular to the axle. I know there are gears that can fit together have teeth, like the attached picture. I know there are other types of mechanisms, and some are more creative. But I also need for the solution to be low friction. What are 2 low friction methods of changing the directional rotation of a power axle 90 degrees? The entire creation is small, probably 12" x 12" Thanks for your help.
Help me please
A V-Belt drive is designed so that it has the input sheave on the shaft of an electric motor (normal torque) rated at .55 hp at 1160 rpm full-load speed. The drive is to a bucket elevator that is to be used 12 hours daily at approximately 675 rpm. The center distance is about 19.5 in. Add the detailed steps of your design to your attached worksheet. Hints: 1) In your design choose an appropriate belt section, specify the small pulley diameter, the large pulley diameter and the length of the belt. Determine the Belt length in inches, in two significant figures. Please enter below a numerical value only, no units are needed. Answer:
Two pulleys are run by a common belt. If a 10.8 inch diameter pulley turns at 900 rpm, what is the diameter of the second pulley if it turns at 421 R.P.M.? Note: Speed is inversely proportional to diameter.
A1 A grinding wheel used in machine shop needs to be analyzed in terms of its suitability for a specific grinding task. Find 1. Accelerating torque produced by the grinding wheel II. Increase in angular momentum of the grinding wheel II. Increase in Kinetic energy of the grinding wheel. Assume the following data Suitable mass of the grinding wheel. Suitable radius of grinding wheel. Select any two Speeds between range 1000 – 3000 rpm. Consider 20 seconds time gap between two speeds selected. 1. 2. 3. 4. Justify your data assumptions.
A pump is driven by an electric motor through a open type flat belt drive.Motor pulley diameter (DS) = 300 mm, Pump pulley diameter (DL) = 600 mm. The Center distance between the pulleys=1000 mm. Find the length of the belt in inches
The BAPCO in Bahrain is looking to design a V belt drive system for its recently installed rotary machines. The smaller pulley having a diameter of * d" is connected to an electric motor and run at a speed of nd. The belt is used to drive a larger pulley at a speed of 90 rpm. The V belt is used to transmits a power of 95 hp and ignore it in belt class selection process (Table 17.9). The service factor for the V belt drive system is 1.3 and the suggested factor of safety for the current design is 2.5. Smaller Pulley Diameter = d = 9 in Speed of smaller pulley = nd = 900 rpm Design and select a V belt drive system.
A belt-driven blower assembly is equipped with a motorthat turns a 5-in. drive pulley at a speed of 3450 rpm.The blower is turning at a speed of 1725 rpm. Determinethe size of the driven pulley.
QUESTION 14 Which one of the below statements is true? For a grounded link rotating with constant angular speed, the magnitude of the velocity vector of a point increases as the point moves away from the pivot. Ob. Kutzbach formula (or criteriong is always reliable in predicting the actual degrees of freedom for any mechanism. C. Springs are considered as links for degree of freedom calculations. O d. Satistying the Grashof criterion means that none of the links in a mechanism makes full rotations.
A belt-driven blower assembly is equipped with a motor that turns a 5-in. drive pulley at a speed of 3450 rpm. The blower is turning at a speed of 1725 rpm. Determine the size of the driven pulley.
19 Rigidity depends on what 3 factors? Gravity, radius of Gyration and direction of spin. Mass of the rotor, radius of gyration, & speed of spin. Wander, drift and speed of spin. Mass of the rotor, distance to spin axis, & direction of spin. 20. The pilot of this aircraft pulls the control column back to start a climb. She makes no change to the engine power. The aircraft loses speed as it converts potential energy into kinetic energy. The total amount of energy in the aircraft reduces. The aircraft's speed remains the same because the engine power is unchanged. The aircraft loses speed as it converts kinetic energy into gravitational potential energy
BDS. Do this on раper. 1. Draw a FBD for the cylindrical tub before the metal object is added, clearly labeling all forces. 2. Draw a FBD for the cylindrical tub after the metal object is added, clearly labeling all forces. 3. Draw a FBD for the metal object after it is placed in the tub, clearly labeling all forces. 4. Take a clear photo of the FBDS and upload that here. BIU E E E E МacВook Pro %24 & 4 5 6 7 R Y 00 ト