3.a. A steel penstock 60 cm in diameter has a shell thickness of 1.2 m. The pipe is required to design to convey a discharge with the mean velocity of 2.1 m/sec. Determine the water hammer head, pressure rise due to sudden closure of the valve by using i. Rigid water Column Theory ii. Elastic Water column theory. Take K = 2.1 * 10°N/mm2 and E = 2.1 * 10°N/mm2.

3.a. A steel penstock 60 cm in diameter has a shell thickness of 1.2 m. The pipe is required to design to convey a discharge with the mean velocity of 2.1 m/sec. Determine the water hammer head, pressure rise due to sudden closure of the valve by using i. Rigid water Column Theory ii. Elastic Water column theory. Take K = 2.1 * 10°N/mm2 and E = 2.1 * 10°N/mm2.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

• A wooden storage vat full of oil sg=0.80 is in the form of a frustum of a cone, 2m diameter at the top and 4m diameter at the bottom, and 3m high. It is provided with two steel hoops one at top and one at the bottom. a. Compute the hydrostatic force on the side of the container. b. How high is the said force above the bottom? c. Compute the force in the bottom hoop.
A water siphon having a constant inside diame of 3 in. is arranged as shown in the figure below the friction loss between A and B is 0.8V²/2 wh is the velocity of flow in the siphon, determine flowrate involved. Assume a = 4 ft, h = 12 ft. D-- B a h
The gauge pressure of water at A is 150.5 kPa. Water flows through the pipe at A with a velocity of 18 m/s, and out the pipe at B and C with the same velocity v. Neglect the weight of water within the pipe and the weight of the pipe. The pipe has a diameter of 50 mm at A, and at B and C the diameter is 29 mm. pw = 1000 kg/m³. (Figure 1) Figure v B v y -X A 1 18 m/s 1 of 1 Part A Determine the x component of force exerted on the elbow necessary to hold the pipe assembly in equilibrium. Express your answer to three significant figures and include the appropriate units. F₁ = Submit Part B F₁ = μA Submit Value Request Answer Determine the y component of force exerted on the elbow necessary to hold the pipe assembly in equilibrium. Express your answer to three significant figures and include the appropriate units. μA Value Units Request Answer ? Units ?
A vertical triangular gate with Alcohol (SG = 0.78) on one side is shown in the figure. Determine the total resultant force acting on the gate and the location of the center of pressure. +dy 3ft Unit weight of the liquid (y) Value of hbar (h) Area of the rectangular gate (A) Hydrostatic Force (F) Value of (Igx) Value of ybar (9) Location of the Hydro.Force measured from the water surface of the gate inclined (yp) Ib/ f ft ft lb fi ft ft ***answer Hydrostatic Force F on the box below:
The gauge pressure of water at A is 150.5 kPa. Water flows through the pipe at A with a velocity of 18 m/s, and out the pipe at B and C with the same velocity v. Neglect the weight of water within the pipe and the weight of the pipe. The pipe has a diameter of 50 mm at A, and at B and C the diameter is 31 mm. pw = 1000 kg/m³. (Figure 1) Figure v B v y L. 18 m/s 1 of 1 Part A Determine the x component of force exerted on the elbow necessary to hold the pipe assembly in equilibrium. Express your answer to three significant figures and include the appropriate units. F = 11176 Submit μА Part B Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining N Determine the y component of force exerted on the elbow necessary to hold the pipe assembly in equilibrium. Express your answer to three significant figures and include the appropriate units. μA Fy=11115 Provide Feedback ? N Submit Previous Answers Request Answer ? X Incorrect; Try Again; 5 attempts remaining
A) Water at 70 °C flows up a 50-ft-long conical pipe with its centerline sloping at 5° to the horizontal, as shown in figure (1). At its lower end the diameter is 24 in, the water pressure is 15 psi; at its upper; outlet end the diameter is 18 in and the water pressure is 12.5 psi. By a method, the shear stress found to be 0.25 lb/ft². Assuming this value to be non-varying, calculate the flow rate. given = 62.30 lb/ft³ 18 in dia Q-? 24 in dia.. 15 pe soft 7₂-0.75 46/4² Figure (1) 12.6 pri
Example ( 8) Steel tube shaft having length 3mm and diameter 50mm subjected to axial compressive force 55 k N and change in temperature ( 100 °c drop). Find the change in length and diameter due to compound effect. Note: - E=200 GPa, u=0.3, a=11.5 Mm/ m'c
A pipe conveys water with velocity 360 m/min and pressure gauge shows 5 bar pressure under which the water is following. The pipe is located at 5 metre above the datum line. The sum of total head and stagnation head is m. (g = 10 m/s?). (assume 1 bar = 105 Pa) %3D
A 4m long quarter clrcular gate of radius 3 m and of negligible weight is hinged about Its upper edge A, as shown in figure below. The gate controls the flow of water over the edge at B, where the gate is pressed by a spring. The water level rises to A at the upper edge of the gate. 3 m Assume: 1. The hinge is frictionless. 2. The weight of the gate is negligible. 3. Density of water = 1000 kg/m3 4. g= 9.81 m/s? The minimum spring force (in kN) required to keep the gate closed is • Spring
Part A 100 mm Determine the volumetric flow of water through the crack. μÅ h Express your answer to three significant figures and include the appropriate units. 1.02.10-6 m³/s Submit Previous Answers Request Answer ?
... T A 30° 2.5m Water hinge L= 2m In the figure shown, a quarter circle gate AOB is hinged at point B. Force "T" at point A is placed at a 30 degree angle from the horizontal to keep the gate in equilibrium. Determine the following: a) Total hydrostatic force "F" = Blank 1 KN b) Force "T" to make the system in equilibrium = Blank 2 KN Blank 1 Add your answer Blank 2 Add your answer
di de= Do Р 45° An involute pump casing is approximated as a toroidal shell as shown in the figure above. It has an internal cross-sectional diameter of d; = 490 mm, an overall external diameter of Do = 1420 mm, and a wall thickness of 4.7 mm. Point A is located at mid-thickness of the wall. (a) Express and in terms of the internal pressure p. Enter only the numerical value of the coefficient associated with p. Р A (b) Determine the maximum internal pressure the shell can hold, such that the Tresca stress intensity at point A does not exceed two-thirds of the yield strength oy = 250 MPa. MPa