Estimate the Hazen-Williams pipe roughness factor, C, for a 250-millimeter (mm) diameter water main. When the flow is 5 million liters per day, the drop in pressure head elevation between two pressure gauges 400 meters apart is two meters of water pressure. 1) 90 2) 115 3) 141 4) 163

Q: 4) In the system below, pipe A has a diameter of 6", a length of 1500 ft and a friction factor of…

A: Given Parallel pipesVelocity in pipe B 5 ft/sLengths of A and B = 1500 and 1000 ftDiameter of A and…

Q: A 300mmx75mm venture meter is inserted in a 300mm diameter penstock where water flows at 55L/s.…

A: A venturimeter of cross-section 300mm×75mm is given, Diameter of pen-stock = 300mm Flow of water…

Q: The pressures at the ends of 605m long horizontal pipe flow are 350kPa and 270kPa. The pressure at…

A:

Q: x 75 mm venture meter is inserted in a 300 mm diameter main pipe where water flows at 55 L/s.…

A:

Q: Q2) water Flow upward at 4 m/s in a 6 cm pipe diameter. the pipe length between point 1 and point 2…

A:

Q: Water Table 10 Cracked Tunnel Lining S. 4. +2 Impermeable Boundary A flow net is shown for a…

A:

Q: Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized aire in the tank. a.)…

A: Q = 50m3/hr  =0.1388 m3/sec f = 0.014 Length of pipe = l = 20+80+40 = 140m

Q: Using the value of Cd, which you have obtained by experiment, determine the throat diameter of a…

A: Solution  Given Data:- Pipe Diameter = 0.6 m  Differential Head = 0.8 m Flow Rate = 0.4 m3/s  Find-…

Q: A 6 in diameter new, unlined ductile iron pipe carries a flow of 150 usgpm and is O.2 miles long.…

A:

Q: For the submerged gate shown, h= 0.81 m and the angle between the y-axis and the vertical plane is…

A: To determine the location of pressure centre on the y-axis of the gate.

Q: A pipe carries an oil of specific gravity 0.8 with pressure 19.62 kPa. The pipe is 3.5 m above datum…

A:

Q: ill be the flowrate? The pipes are galvanized iron with k, = 0.0005 ft. Take v = 1.06 x 5 ft/s and…

A: To find:Flow rate

Q: The diameter of a pipe gradually reduces from 1 m to 0.7 m. the pressure intensity at the centre…

A:

Q: Water flows through the pipe shown at 5 liters per second. If gage pressures of 12.5 kPa, 11.5 kPa…

A: Given:-  Water flows through the pipe shown at 5 liters per second. If gage pressures of 12.5 kPa,…

Q: SUBJECT IS HYDRAULICS SHOW DETAILED AND COMPLETE SOLUTION USED 3 DECIMALS FOR THE FINAL ANSWER The…

A: Given

Q: A steel pipe has an inside diameter of 25mm, is 20 meter long, carries 10degree water at the rate of…

A: what is the static pressure of the water at the outlet,P2=?

Q: A 300 mm x 75 mm venturi meter is inserted in a 300 mm diameter pipeline where water flows at 55…

A:

Q: Water is flowing in a straight concrete lining centrifugally spun pipe as shown in the figure…

A: The given data is: Length of pipe=310 m Difference between gauge reading, hf=185 kpa…

Q: PROBLEM 2 The pipe bend shown is in a horizontal plane. Oil with a specific gravity of 0.86 enters…

A:

Q: Compute the lost head in a 150-mm pipe if it is necessary to maintain a pressure of 231 kPa at a…

A:

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?