2-1 A compound bar consists of a circular rod of steel of diameter 25 mm, rigidly fitted into a copper tube of internal diameter 25 mm and thickness 2.5 mm. If the bar is subjected to an axial load of 100 kN, find the stresses developed in the two materials. Given, E = 2 × 105 N/mm² and Ecu 1.2 x 105 N/mm². = Steel tube '25mm 2.5mm Copper tube

2-1 A compound bar consists of a circular rod of steel of diameter 25 mm, rigidly fitted into a copper tube of internal diameter 25 mm and thickness 2.5 mm. If the bar is subjected to an axial load of 100 kN, find the stresses developed in the two materials. Given, E = 2 × 105 N/mm² and Ecu 1.2 x 105 N/mm². = Steel tube '25mm 2.5mm Copper tube

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c= 1.7m. a b I Steel: A 900 mm Bronze: A E 200 GPa E 83 GPa L-2.0m L=1.5m What is the value of P without exceeding the allowable stress of steel, in KN? 230 250 280 340 1200 mm
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c = 1.7m. b C NANTSELEINE Steel: A = 900 mm² E = 200 GPa L=1.5m Bronze: A=1200 mm² E=83 GPa L=2.0m What is the ratio of the elongation of steel to bronze? O 0.367 O 0.433 O 0.467 0.333
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c= 1.7m. a b C P Steel: A-900 mm² Bronze: A=1200 mm² E = 83 GPa L=2.0 m E = 200 GPa L=1.5m What is the value of P without exceeding the allowable stress of bronze, in kN? O 161 O 174 O 145 124 4
A bar of solid circular cross section is loaded in tension by forces P (see figure). P L The bar has a length L = 14.0 in. and diameter d = 0.65 in. The material is a magnesium alloy having a modulus of elasticity E = 6.4 x 106 psi. The allowable stress in tension is allow = 17,300 psi, and the elongation of the bar must not exceed 0.04 in. What is the allowable value of the forces P (in lb)?
A two pinned end bars AB (copper) and BC (aluminum) is subjected to a horizontal force P = 90KN applied at pin B %3D as shown in the figure, determine the horizontal displacement of pin B. Aluminum: L= 1.5m, A= 1000mm2, E= 70 GPa Copper: L= 2.0m, A= 850mm², E= 120 GPa Degree: 45° Alumaum L-15m A=1000 mm E-70 GPa >P=90 kN Copper L=2.0m Aa550 mm E=120 GPa
A hollow aluminum tube is rigidly attached between steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in aluminum of 80 MPa, in steel of 150 MPa or bronze of 100 MPa. Steel Aluminum Bronze А P> ЗР - 2P outside = 30 mm d inside = 20 mm d d = 16 mm d = 60 mm -100mm- -150mm- -125mm-
Ex: Find the stress in steel and aluminum if the bars are rigid. Steel L = 0.6 m 60 KN E =200 Gpa A= 100 mm? A Aluminum L = 1m 2m 2m E = 70 Gpa A = 300 mm²
The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar (1) is a bronze alloy [E = 110 GPa] with a cross-sectional area of A1 = 210 mm2. Bar (2) is an aluminum alloy [E = 73 GPa] with a cross-sectional area of A2 = 620 mm2. All bars are unstressed before the load P is applied; however, there is a 2-mm clearance in the pin connection at A. Assume L1 = 2150 mm, a = 1050 mm, b = 630 mm, c = 490 mm, and L2 = 1600 mm. If a load of P = 60 kN is applied at B, determine (a) the normal stresses in both bars (1) and (2). (b) the downward deflection of point A on the rigid bar.
2. Solve for the deformation of the aluminum rod. 200 mm 300 mm 600 kN Aluminum E= 70 GPa A= 900 mm Steel E= 200 GPa A=1200 mm
The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar (1) is a bronze alloy [E = 102 GPa] with a cross-sectional area of A₁ = 200 mm². Bar (2) is an aluminum alloy [E = 72 GPa] with a cross-sectional area of A₂ = 640 mm². All bars are unstressed before the load P is applied; however, there is a 2-mm clearance in the pin connection at A. Assume L₁ = 1880 mm, a = 1060 mm, b = 620 mm, c = 480 mm, and L₂ = 1270 mm. If a load of P = 71 kN is applied at B, determine (a) the normal stresses in both bars (1) and (2). (b) the downward deflection of point A on the rigid bar. (1) L₁ b tc B (2) D L2
A 50 mm diameter cylindrical aluminum block is connected to 2 hollowed cylindrical steel blocks as shown in Figure. Both hollowed steel cylinders are of 60 mm and 40 mm outer and inner diameters respectively. The assembly is then connected to a rigid steel plate. Four bolts of diameter 10 mm are then used to rigidly fix the assembly to a wall. A force P is then applied to the assembly. The Modulus of elasticity(E) of steel is 200 GPa while aluminum has Modulus of elasticity(E) of 70 GPa. Both steel and aluminum have a yield strength (σy) of 250 MPa. The bolts have a yield stress (σy) of 800 MPa. All connections and joints are considered rigid.All lengths are in mm. a. Determine the allowable value of P that can be applied to the assembly taking into consideration theyielding of all parts of the assembly and bolts. Use a factor of safety of 1.5.b. Based on the value of P obtained part (a), determine the total elongation of the cylindrical steel block.c. Based on the value of P obtained…
2. A rod is composed of an aluminum section rigidly attached between steel and bronze sections as shown in the figure. Axial loads are applied at the positions indicated. The cross-sectional area of the rod is 300sq.mm. Express your answer in MPa. Determine the stress in the steel. b. a. Determine the stress in the aluminum. Determine the stress in the bronze. C. STEEL ALUMINUM BRONZE 56kN 14kN -0.6m- -0.9m- -0.76m-