3. Suppose in Step 12 of Part A, a student suspended the synthesized aspirin using hot water instead of ice water. How would this influence the percentage yield of the isolated aspirin compared to that obtained if ice water had been used? a. Increase it. b. Decrease it. Explain your answer: c. Would not influence it.

3. Suppose in Step 12 of Part A, a student suspended the synthesized aspirin using hot water instead of ice water. How would this influence the percentage yield of the isolated aspirin compared to that obtained if ice water had been used? a. Increase it. b. Decrease it. Explain your answer: c. Would not influence it.

EBK A SMALL SCALE APPROACH TO ORGANIC L

4th Edition

ISBN:9781305446021

Author:Lampman

Publisher:Lampman

Chapter80: Crystallization: Purification Of Solids

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

How are the boiling point and freezing point of water affected by the addition of solute?
Graph Table 14.10 shows solubility data that was collectedin an experiment. Plot a graph of the molarity ofKI versus temperature. What is the solubility of KI at55°C?
5. Barium chloride is reacted with sodium sulfate to produce barium sulfate and sodium chloride. How many moles of the precipitate is produced from 0.8 moles of BaCl2?A. 0.4 moleB. 0.8 moleC. 1.6 molesD. None of the above 6. 315mL of water was added to 2100 mL of 19M NaCl solution. What is the new concentration of the solution?(Use the given information: MW: Na = 23g / mol , CI=35g/mol)A. 2.85 MB. 2.48 MC. 18.60 MD. 19.0 M
The following questions all are based on the data in this table: Substance Solvent Temp.,oC Solubility, g per 100 mL X heptane 20 23.5 X heptane 80 27.0 X 1-propanol 20 0.6 X 1-propanol 80 8.7 Y heptane 20 4.0 Y heptane 80 4.0 Y 1-propanol 20 22.0 Y 1-propanol 80 31.0…
4. A student obtained the following data:Freezing point of Lauric acid: 43.5oC Freezing point of Lauric acid containing an unknown solute: 41.2oCThe freezing point depression constant for Lauric acid: 3.9oC/molal The molality of the unknown solute is closest to: A. 0.6m B. 1.6m C. 1.7m D. 0.3m E. 2.3m F. 3.9m G. zero 5. Given the following data: Flask A with 50cm2 surface area contains 100mL of water at 25oC; Flask B with 20cm2 surface area contains 10mL of water at 55oC. In which flask does the water have a lower vapor pressure?A. flask A B. flask B C. both flasks have the same vapor pressure
In which compound will sodium chloride dissolve? Select one: a.carbon tetrachloride (CCl4) b. methanol (CH3OH) c. pentane d. none of these e. all of these
2. What is the concentration of a solution that contained 0.3 moles of solute dissolved in 50mL of solvent? а. бх10ЭМ b. 0.167M С. 6M d. 166.7M
15. How much calcium chloride would you dissolve in 250 mL to make 120 ppm primary standard solution of Ca2+ ion? (molar mass of Ca is 40 g/mol and the molar mass of CaCl2 is 111 g/mol) a. 83.3 mg b. 20.6 mg C. 15.0 mg d. 17.6 mg
Comparison: Write A if an increase in one variable will increase the other one. Bif an increase in one variable will decrease the other one. Cif the two quantities are equal Dif the two quantities cannot be compared 1. The rate of dissolving if stirring is used. 2. The solubility of a gas in liquid if the T is increased. 3. The rate of dissolution when hot solvent is used. 4. The amount of solute in supersaturated solution if solvent is increased. 5. The amount of solute in a saturated solution if more solute is added. 6. The normality of a 1.0 molar acidic solution when triprotic acid is used. 7. The solubility of gas if pressure is decreased. 8. The molarity of an 'acidic and basic solutions. 9. The normality of an acidic solution if a monoprotic acid is used. 10. The molarity of solution if the temperature is increased. 11. The boiling point of solution if the molal concentration is increased. 12. The freezing point of solution if the temperature is decreased. 13. The amount of…
Materials Needed solid I2 solid CUSO4-5H20 food dye solid (NH4)2SO4 heavy metals waste container halogenated waste container non-halogenated waste container semi-micro test tubes and rack regular test tubes and rack squash pipettes acetone cyclohexane propan-2-ol Method Part A: Solubility of ionic and molecular solids 1. Place a small amount (about the size of 1 grain of rice, see picture) of copper sulfate into each of three DRY semi-micro test tubes. Add 20 drops of water to the first test tube and gently flick the test tube with your finger to ensure mixing. 2. Repeat step 1 using acetone in place of water as the solvent in the second test tube. 3. Repeat step 2 replacing acetone with cyclohexane in the third test tube. Hold the test tubes against a white background to compare the solubility of copper sulfate in the three solvents and record your results. Discard these mixtures into the heavy metals waste container in the fume cupboard. Once these test tubes have been emptied you…
What can be obtained in greatly diluted solutions and presence of a small excess of one of the components? Select one: a. the salt the compound the reaction d. colloidal dispersion (micelle) e. the precipitate C.