Question 3 A triangular water trough is "a" metres wide and "a" metres deep, as shown in Figure 3. If the trough is filled with water, calculate the magnitude and location of the resultant force acting on the triangular end plates (shaded in grey). The density of water is 1000 kg/m³ (ignore the atmospheric pressure). Use the value of "a" corresponding to the last digit of your SID from Table 1. "a" m "a'm Figure 3: Triangular water trough a=7

Question 3 A triangular water trough is "a" metres wide and "a" metres deep, as shown in Figure 3. If the trough is filled with water, calculate the magnitude and location of the resultant force acting on the triangular end plates (shaded in grey). The density of water is 1000 kg/m³ (ignore the atmospheric pressure). Use the value of "a" corresponding to the last digit of your SID from Table 1. "a" m "a'm Figure 3: Triangular water trough a=7

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.17P: A man weighs 170 lb on the surface of the earth. Compute his weight in an airplane flying at an...

See similar textbooks

Similar questions

A man weighs 170 lb on the surface of the earth. Compute his weight in an airplane flying at an elevation of 28 000 ft.
The given Figure is shown a curve surface. It is required to determine the magnitude, direction, and line of action of the vertical component, the horizontal component, and the resultant hydrostatic force acting on the surface in case () is 1.3 m, specific weight of water is 9770.5 N/m3, and width of the curve is 1.8 m. 1. B Water (write here only FH with two numbers after the decimal xxxxx.xx) for full answer use the pdf file 719
A vertical triangular plate whose height is 4 m. has its base horizontal at the bottom. The difference in level between the center of gravity and the center of pressure shall be 22 cm. What is the base width of the plate i the water surface total hydrostatic force acting on the plate is 76.28 KN. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: m Decimal Places required in' the final answer: 3
The flat surface shown is submerged vertically in water. Find the fluid force against the surface. The weight density of water is 62.4 lb/ft. 4ft 8 ft Enter the exact answer. F = lb exact number, no tolerance
If the absolute pressure in gas is 40 psia and the atmospheric pressure is 846 mbar abs, find the gage pressure in bar. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: bar Decimal Places required in the final answer: 3
The answers for question 1 ie. Volume of each tank is given and attached here. But you need to still show the calculations for it
The end plates (isosceles triangles) of the trough shown to the right were designed to withstand a fluid force of 6400 lb. Assuming the density of water is 62.4 lb/ft³, how many cubic feet can the trough hold without exceeding this limitation? What is the value of h, the depth of water that exerts a fluid force of 6400 lb? What is the integral that gives the fluid force exerted on the end of the trough when filled with water to a depth of h? h Sody The maximum volume is ft³. (Round down to the nearest cubic foot.) The value of his (Round to two decimal places as needed.) (-3,14) (0,h) y (ft) (3,14) 14 y 3x x (ft) 0 End view of trough 14 ft 30 ft 6 ft → Dimensional view of trough
M1 U5: Use the general solution in determining the total hydrostatic force acting on the submerged curved surface. Please provide the complete UNITS ANALYSIS, USE OF CORRECT CONVERSION RATIOS and DIAGRAMS in your hand-written solution. INCOMPLETE/NO SOLUTION means NO CREDIT. Encode your FINAL answer in the space provided after each question. A curved surface is formed as a quarter of a circular cylinder with R = 0.75 m as shown. The surface is w 3.55 m wide. Water stands to the right of the curved surface to depth H = 0.60 m. seawater 0.60 m (SG = 1.03) %3D 0.75 m Determine the magnitude and direction of the horizontal component of the hydrostatic force (in N) acting on the gate. Indicate the direction by putting an R for right and L for left after your numerical answer. Your answer
The flat surface shown is submerged vertically in water. Find the fluid force against the surface. The weight density of water is 9810 N/m. 6m 5m 8m Enter the exact answer. F = %3D
1 - At what depth below the surface of the oil, relative density 0.89 will produce a pressure of 120 kN/m2. What depth of water is this equivalent to? Depth of oil in meters Answer for part 1 Depth of water is this equivalent to
Given that the weight density of water is 9810 N/m3, calculate the fluid force (in Newtons) on a rectangular 1.6m cross times 2m flat plate submerged horizontally in water at a depth of 4m. Give your answer correct to two decimal places without the units. Round your answer to 2 decimal places.
Shown to the right is a vented tank filled to the top with ethylene glycol. The tank has a breadth (depth into your paper) of 8 ft. Note the curved surface is NOT a full quarter circle, it is a pie segment. Use the link to Efunda.com on the course home page in Angel to find the geometric properties of a pie segment. a. Determine the magnitude of the horizontal and vertical components of force acting on the curved surface. Determine the location of the center of pressure. 10' Ethylene 35⁰ 10'