3. (a) A 3200c.c. Spark Ignition (SI) V6 engine operates on a four stroke cycle at 7800RPM. The engine compression ratio is 9.2, the length of the connecting rod is 15.6cm, and the engine has a bore/stroke ratio of 1.7. At this speed, combustion ends at 34° ATDC. Calculate: i Cylinder bore and stroke length. ii Average piston speed 12 iii Clearance volume of one cylinder. (b) The same engine is connected to a dynamometer which gives a brake output torque reading of 175Nm at 7800 RPM. At this speed, air enters the cylinders at 80kPa and 65°C, and the me- chanical efficiency of the engine is 80%. Calculate: i Brake power ii Indicated power iii Brake mean effective pressure iv Indicated mean effective pressure u

3. (a) A 3200c.c. Spark Ignition (SI) V6 engine operates on a four stroke cycle at 7800RPM. The engine compression ratio is 9.2, the length of the connecting rod is 15.6cm, and the engine has a bore/stroke ratio of 1.7. At this speed, combustion ends at 34° ATDC. Calculate: i Cylinder bore and stroke length. ii Average piston speed 12 iii Clearance volume of one cylinder. (b) The same engine is connected to a dynamometer which gives a brake output torque reading of 175Nm at 7800 RPM. At this speed, air enters the cylinders at 80kPa and 65°C, and the me- chanical efficiency of the engine is 80%. Calculate: i Brake power ii Indicated power iii Brake mean effective pressure iv Indicated mean effective pressure u

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

!
Don't Use Chat GPT Will Upvote And Give Handwritten Solution Please
Solve it . Writing is not handwritten plz
The following shows the top view of the partially open doors on one side of an entertainment center cabinet. The wooden doors are hinged to each other and one door is hinged to the cabinet. There is also a ternary, metal link attached to the cabinet and door through pin joints. As spring- loaded piston-in-cylinder device attaches to the ternary link and the cabinet through pin joints. Draw a kinematic diagram of the door system and find the mobility of this mechanism. cylinder piston O cabinet link hinge door door hinge
2 Parts ( C & D) in image below read & and solve carefully.
Figure Q1 (a) and Figure Q1 (b) shows a C-shape block and rectangular hollow block respectively.
Re-work Problem 4 on Homework 2 using Lagrange's equations (see Figure 4 below). As indicated in the original problem statement, find the equations of motion and the constraint force (Hint: to find the constraint force, introduce an additional generalized coordinate and associated Lagrange multiplier).
Evaluate the 3-DOF wrist as shown in Figure 2, use the conventional method to determine 1. Linear velocity and 2. Angular velocity NOTE: for JOINT 3 ( 03 ) only Connected to robot arm Pitch Roll Yaw Figure 2: Wrist assembly The known position and orientation of the end of the arm point is. C, C2 [-C,S2C3 + S¼S3 -S;S2C3 – C1S3 C2C3 C¡S2S3 + S1C3 S4S2S3 + C,C3 -C2S3 01 S,C2 S2 1 °T3=°T¡'T2²T3
Q/2: According to figure below, the component is to be faced and then turned, write A typical program for the required moves of CNC Machine: (all units in (mm) and Absolute). Material Aluminium Row material size 320 60 mm long. 63 I 48 43 40 R3 26 20 10
Can someone please help me to solve only number 7 and number 8 of this question. Thank you!
A realistic CAD model of the whole jack must be produced from which you will generate an assembly drawing. Standard bought-in components must be specified. Material specifications of components listed in your 'bill of materials' must be provided. Detail designs calculations, for the main pivots, hydraulic actuation safety system, must be carried out.
Fast plzzzzz. Hand written plz asap please fast and if hand written i'll upvote otherwise downvote