Two transmission belts pass over a double-sheaved pulley that is attached to an axle supported by bearings at A and D. The radius of the inner sheave is 125 mm and the radius of the outer sheave is 250 mm. Assuming that the pulley rotates at a constant rate and Ta 112 N. Tg-84 N, and TC-175 N, determine the reactions at A and D. Assume that the bearing at D does not exert any axial thrust 150 mm The reaction at A is ( The reaction at Dis 100 mm 200 mm N NJ+ NIK Nik

Two transmission belts pass over a double-sheaved pulley that is attached to an axle supported by bearings at A and D. The radius of the inner sheave is 125 mm and the radius of the outer sheave is 250 mm. Assuming that the pulley rotates at a constant rate and Ta 112 N. Tg-84 N, and TC-175 N, determine the reactions at A and D. Assume that the bearing at D does not exert any axial thrust 150 mm The reaction at A is ( The reaction at Dis 100 mm 200 mm N NJ+ NIK Nik

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.125P: The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A...

See similar textbooks

Similar questions

For the following calculate the reactions at A and B. 2 kN-m 6 kN-m 60° 2 m
The operation of the fuel pump for an automobile depends on the reciprocating action of the rocker arm ABC, which is pinned at B and is spring loaded at A and D. The smooth cam C is in the position shown. The vertical force acting on the rocker arm at A is F = 80 N, and at C it is Fc = 115 N. (Figure 1) Figure 10 m 1 of 1 > 20 mm- Part A Determine the z and y components of the reaction force on the rocker arm ABC at the pin for equilibrium. Express your answers using three significant figures separated by a comma. B. By Submit Part B Az it vec Bequest Answer FD- Value Determine the magnitude of the force along the spring DF for equilibrium, Express your answer to three significant figures and include the appropriate units. Submit Request Answer Units ? ? N
2. Find the reactions at A and B. 4" 4" 12 C D 6" 4 IB 7" A 3 T = 30 lb
Determine the reactions at A and C. * 60° 4 ft 2 ft 2 ft 200 lb Ra = 187.20 Ib up to the right, 16.1 deg from x axis, Rc = 60 lb Ra = 182.07 Ib up to the right, 16.1 deg from x axis, Rc = 50 lb %3D Ra = 180.27 Ib up to the right, 16.1 deg from x axis, Rc = 50 lb %3D Ra = 180.27 Ib up to the right, 16.1 deg from x axis, Rc = 60 lb
The cylinder have equal diameter. Solve for the reactions at A, D and C.
Solve for the reactions at A.
Determine the components of reaction at E. Take that P= 5.1 kN and w = 3.6 kN/m (Figure 1) Figure 1 of 1 1.5 m -1.5 m
Find the support reactions at points A and B. A 3 kN 1m im 10 kN 10 kN 1 m B 2 m m 2.
5. DRAW THE FIGURE THEN SOLVE FOR THE REACTIONS AT A AND B. 3DN 15N KN Im * lan -4m B
4-105 - The overhead transmission shaft AE is driven at a constant speedby an electric motor connected by a flat belt to pulley B. Pulley Cmay be used to drive a machine tool located directly below C,while pulley D drives a parallel shaft located at the same height asAE. Knowing that TB + TB' = 162 N, TC = 180 N, TC' = 72 N, TD = 0 and TD' = 0, determine:(a) the tension in each portion of thebelt driving pulley B(b) the reactions at the bearings A and Ecaused by the tension in the belts.
solve for the reactions at A and B
Determine the components of reaction at D. Take that PP_1 = 11 kN and P_2 = 18 kN .