Answer number 26 with complete solution thank you For nos. 24-37, satisfy the conditions of the given problembelow: The truss is loaded as shown in figure 2. By methodof joints determine the force in each member, andstate if under tension or compression.24. Reaction at support A5 kN3 kND1mO A. 7 KNO C. 8 KNO D. 9 KNB. 7.5 KN2 m2 mB2 m 25. Load on member FAO A. 9.4 KN. (C)O B. 9.4 KN (T)O C. 11.2 KN (T)O D. 11.2 KN (C)26. Load on member FEO A. 9.05 KN (C)B. 9.50 KN (T)O C. 10.2 KN (T)O D. 11.3 kN (C)27. Load on member EDO A. 9.05 KN (C)B. 9.50 KN (T)O C. 10.2 kN (T)OD. 11.3 KN (C)

Answered: Image /qna-images/answer/95ea5555-95b7-46eb-82a6-6869d9a1c09e.jpg

Answered: 26. Load on member FE OA. 9.05 KN (C)…

Engineering

Mechanical Engineering

26. Load on member FE OA. 9.05 KN (C) OB. 9.50 KN (T) O C. 10.2 kN (T) OD. 11.3 kN (C)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Show your complete solution including the diagrams and box your final answers with their appropriate…

Q: Draw the following figure: 50000- 8.0000

A: The drawing of the given figure will be:

Q: 4. The surface temperature of the hot side of the furnace wall is 1200 degrees C. It is desired to…

Q: If 17 welders can complete a job in 134 hours, how long will it take for 21 welders to do the same…

Q: 8. A note in the comment section of a title block mentions that all faces should have a +.10…

A: Circularity (roundness) tolerance is 2-D in nature.

Q: How would tou answer #10?

A: As mentioned in the question to solve #10, i will solve only question 10th

Q: Write any four problems caused by insert solids. What solution can be given to those in order to…

Q: Give one problem solving question about "Method of Sections" and show the solution

Q: 1500 liters/s of ammonia gas at 100°F and pressure of 30 in.Hg has a specific heat ratio of 1.304.…

A: Given data Q=1.5 m3/sT1=100°FT2=180°Fγ=1.304 Here, Q is the flow rate and T1 is the initial…

Q: I need the complete procedure, that is, where did you find the value of 895

A: How the value 895 came in the formula

Q: 2. From the given figure below, solve for the bar Y from the reference line. (choose the nearest…

Q: What are the different types of force? Applied Tension Gravitational Spring Air Resistance Normal…

A: (I) Force has been classified on the basis of contact which is as follow 1. Contact force:- These…

Q: 1. Given the following measurements (in metric and English respectively) of a metal cylinder: length…

A: as you mentioned I solved 1st. one. For solution refer below images.

Q: A diesel engine in a power plant has an output of 150 KW at 260 rpm. It uses fuel oil having a…

A: Given data: Diesel engine power output = 150 kW @ 260 rpm Calorific Value of Fuel oil = 43912 kJ/kg…

Q: Solve for the mobility. Show your logical and accurate solutions after every fig

Q: Q34 gine exCumphe far nolineer operautor an

A: Given: To give an example of non-linear operator.

Q: Determine the skin due to perforation for a vertical well completion scheme described below: Payzone…

A: To Find:the skin factor due to perforation for a vertical well completion scheme.Given:The pay zone…

Q: Please answer questions 7,8, show reasons and examples

A: The characteristic equation of the system is:x^6 + (73*x^5)/40 + (1969*x^4)/48 + (22309*x^3)/600 +…

Q: I needed it to be solved using differential equation

Q: Thank you . But where did you get 12 from ?

A: Given- The width of the rectangular beam b = 140mm The depth of the rectangular beam h = 110 mm…

Q: 1. The assembly consists of two sections of galvanized steel pipe connected together using a…

Q: Q3: Mark the Following True or False 1. Hatching of different components is done on same direction.…

Q: . Convert the octal number 23228 to its decimal number equivalent, (base-8 to base-10).

A: Givenoctal number =23228

Q: A 25 ft long solid steel rod is subjected to a load of 10,000 Ib. This load causes the rod to…

A: Data given - L = 25 ft = 25 × 12 P = 10000 lb ∆L = 0.477 in E = 30 × 106 psi

Q: How many cutting-plane lines are shown on this print?

A: Cutting plane lines:Cutting plane lines are the lines used to show the direction of the cut-way…

Q: la) Compare the relative load strength of the following two bolts: Bolt 1 = %" Dia x 3" Long and is…

Q: A closed cylindrical vessel contains a fluid pressure of P (Mpa). The cylinder has an inside…

A: Given:Syt=340 MPad=2.5 mt=31.8 mmN=2.5

Q: • Use hexagonal head screw/bolt with jam locking nut through clearance holes to fix the two parts…

Q: LEASE ANSWER ALL OF THE GIVEN QUESTIONS. Choose from the given choices/options below the…

A: Given Data : Motion of projectile

Q: I need these three parts answered pertaining to the print provided. If you can not answer all three…

A: The term, Orthogonal, describes the relationship of the axis of the ½” NPT pipe plug with the main…

Q: Please give the details explanation of the answer

Q: General Directions: Solve what are asked for in the following problems. Show complete solutions by…

Q: can u pls solve the question using hand written notes in detail and figure

Q: Let me know if I have misinterpreted the question.

A: in this question all the help full values are given.In this question plate slider due to impact…

Q: 4. Calculate the heat loss per linear foot from a 10.3 in. nominal pipe (outside diameter=10.75 in.)…

A: Heat transfer in hollow cylinder: q˙= ∆TR Where ∆T →Temperature difference R → Thermal resistance…

Q: Quenching is a process that can reduce the grain size and form a lot of grain boundaries in the…

A: Quenching: In this process metal is heated above its recrystallization and than cool it rapidly. The…

Q: Calculate the mechanical advantage of the following compound machine.

Q: Give a steps by steps answer of the solution

Q: Problem A solid uniform ball with mass m and diameter d is supported against a vertical frictionless…

Q: Match the given functions with the components of a wind turbine. Connects the rotor hub to the gear…

A: a) Main Shaft connects the rotor hub to the gearbox.

Q: Choose from the given choices/options below the question. I will rate you with “UPVOTE/LIKE” if…

A: Given Data : Spring force work

Concept explainers

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.

Question

Answer number 26 with complete solution thank you

For nos. 24-37, satisfy the conditions of the given problem
below: The truss is loaded as shown in figure 2. By method
of joints determine the force in each member, and
state if under tension or compression.
24. Reaction at support A
5 kN
3 kN
D
1m
O A. 7 KN
O C. 8 KN
O D. 9 KN
B. 7.5 KN
2 m
2 m
B
2 m

25. Load on member FA
O A. 9.4 KN. (C)
O B. 9.4 KN (T)
O C. 11.2 KN (T)
O D. 11.2 KN (C)
26. Load on member FE
O A. 9.05 KN (C)
B. 9.50 KN (T)
O C. 10.2 KN (T)
O D. 11.3 kN (C)
27. Load on member ED
O A. 9.05 KN (C)
B. 9.50 KN (T)
O C. 10.2 kN (T)
OD. 11.3 KN (C)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A technician uses these items in fixing a hot water heating system:Find the total cost of the items used.Note: Use this information and diagram for problems 21 and 22. TheR value of a substance gives the resistance of a substance to heatflow. The larger the R value, the more resistant the substance is toheat flow and heat loss. The total resistance is the sum of each substance’s resistance.
need Z. Need only handwritten solution only (not typed one).
Kindly solve what is ask and provide a complete solution so I can understand. I want a handwritten solution. Thank you!
Please assist with this practice question. I don't know where to begin with this. Give details on how to do. Thank you.
Where did you get the 3 from for the distance of q?
I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the example shows on problem number 1. Here is the link to the questions I already had answered, could you please rewrite the answer so its properly answered as the example shows (Problem 1)? https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/cadc3f7b-2c2f-4471-842b-5a84bf505857
I am attaching both questions for 4 and 5 with the question in the image. thank you. NOTE : So the last person answered this question WITHOUT refencing the answer for whether question 4 or 5 answeres were given, so i am asking for question 5(or the answer for the question that was NOT solved because it was not referenced.) These were the following answers given to me from the last person on bartleby who answered my question without referencing whether it was the answer for question 4 or 5. 1 pass 2 fail 3 fail 4 pass
Number 4
PLEASE ANSWER QUICKLY WITH 30 MINUTES PLEASE FOLLOW THE INSTRUCTION THANKS
*NOTE ON INSTRTUCTUONS AND HINTS
Paula has worked for Brindle Corporation for 3 years. During this time, she has worked as a machine operator/cell leader in various work cells. Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel. These tubes get a hole punched in them, a flange welded on, and burrs ground off. The pipe then gets placed into a gage to check that it was made correctly. (The tubes weigh about six pounds.) Paula has been performing the welding operation. She leans into the machine and loads the part into a fixture then positions the flange. Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position of the hole and a…
Test-II. Write down all the operations or step by step procedure on how to create the object below. Write down also the name of the machines and the tools that you will use to complete the drawing below. 824 020 015 22 15 35 40 100 NOTE: ALL DIMENSIONS ARE IN MM ALL CHAMFERS ARE 1X 45