Fill in the Blanks:Type your answer in the space provided after each item. Type in your answer/s rounded off to 2 decimal places except for whole numbers. (ex: 10.67, 28, 732.40)If your answer is 120.00 kN, just write 120 kNDo not round off values during solving. Use the store function of your calculator or its fraction if applicable. Include the units specified after your answer. Leave a space between the value and the unit. (ex: 6323.17 m, 73.10 lb-in, 100 kN) An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure. Axial loads are applied at the positions indicated. If the rod should not exceed a stress in steel of 132 MPa, in aluminum of 82 MPa, or in bronze of 112 MPa:AluminumA = 400 mm?BronzeSteelA = 200 mm?A = 500 mm?2P4P2.5 m2.0 m1.5 m1.) Find the value of P considering only the steel member.Compression or Tension?a. 13200 Nb. 11000 Nc. 12200 Nd. 5600 N2.) Find the value of P considering only the aluminum member.Compression or Tension?a. 26300 Nb. 15000 Nc. 32000 Nd. 32800 N3.) Find the value of P considering only the bronze member.Compression or Tension?a. 10200 Nb. 11200 Nc. 92000Nd. 89100 N4.) Find the maximum value of P.a. 10200 Nb. 11200 Nc. 8500 Nd. 5600 N

Answered: Find the value of P

Engineering

Mechanical Engineering

Find the value of P

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.3.26P: A plane frame with a pin support at A and roller supports at C and £ has a cable attached at E....

See similar textbooks

Related questions

Q: Point X moves in a circular path of 6-m radius so that its arc distance from an initial position Y i...

A: Answer: The normal component of acceleration of the point is 32.667 m/s2.

Q: 1- compressor with compression ratio (7:1). The pressure, temperature and volume at the beginning of...

Q: ROLLER GATE WATER SURFACE R=4 m WATER SURFACE c 307 6.0 m 30 HÍNGE DAM Fig. 3.60 Fig. 3.59 21. Find ...

Q: A circular plate of diameter 3 m is immersed in water in such a way that its least and greatest dept...

Q: Deturmine M- sy B- IN S = Im * (E). L2 - am • &N. filt) O (t) e0.1t 19 cos t+) -t+ ) 8/15 ¤ (t) : VI...

A: Deriving Equation of motion using Newton's 2nd law.

Q: 20 long tons of ice per 12 hrs at -15 °C were produced from steam at 190 °C. If there is no miscella...

A: Refrigeration effect is the amount of heat that is required to extract from the storage space in ord...

Q: A bracket ABCD having a hollow circularcross section consists of a vertical arm AB (L 5 6 ft),a hori...

Q: An electric motor delivers 5 HP to a hydraulic pump with an overall efficiency of 90%. The pump prov...

Q: A The t a ef t e te en te Determine the following a. Shearing Stress in the head bolt. b. Shearing i...

Q: The truss is supported by a pin connection at A and a roller at E. It is loaded as shown. Use the pi...

Q: Where are the application of slider crank mechanism? Answer at least five applications

A: Slider Crank Mechanism is most widely used mechanism, they are used in a number of places like, 1. E...

Q: is q in < q out in power cycles, heat pump cycles, or refrigeration cycles?

Q: N value (x,y,z): 10,14,17 In case you can't read the given values on the picture: B: (6,7,8) C: (5,1...

Q: An infinitely long cylindrical container has a cross section area of radius R, and is placed horizon...

A: Pressure is caused by the force pressing on an area, according to physics. The weight operating on a...

Q: 5. Find the approximate shear stress

A: To find approximate shear stress developed Exact shear stress developed deformation of the spring

Q: A centrifugal pump consists out of an impeller, diffuser and casing and is powered by 300 kW (shaft...

Q: As an industrial engineer, in what ways could you incorporate the use of flow process diagram in you...

A: There are a lot of ways in which I can use a process flow diagram in my daily life as an Industrial ...

Q: What rating is used to find the full-load running current of a torque motor?

A: Given Torque motor To find Rating for full load running current

Q: An external load caused tensile stress is imposed along the [001] of a BCC single crystal. The initi...

A: Body-Centered cubic (BCC) is the name given to a kind of iota plan found in nature. A body-focused c...

Q: 1 (a) A plate 0.05mm distant from a fixed plate moves at 1.15 m/s and required a force per unit area...

Q: PProb. 2.8-10. A load W is to be suspended from a cable at end C of a rigid beam AC, whose length is...

A: Given Data The stress acting in the y axis for the rod BD is: σy=250 MPa The modulus of elasticity ...

Q: Calculate the support reaction forces for the above beams. Draw shear and moment diagrams.

A: To find: The reactions at A: Ax = ?, Ay = ?, and MA = ? To draw the Shear force diagram and bendi...

Q: 10A plate 0.05mm distant from a fixed plate moves at 1.25 m/s and required a force per unit area of ...

A: GIVEN DATA- 1(a) SHEAR STRESS =2.2N/m2 , U=1.25 m/s , y=0.05mm , Specific gravity of oil =0.7 1(b) V...

Q: polypropylene PP rod attached ceiling 200 mm tick 25 mm width,3 mm length in loaded with 30 kg . fin...

A: Given data Thickness of Polypropylene rod = 200 mm Width = 25 mm Length = 3 mm Load = 30 kg Time = 2...

Q: Determine the change in entropy for the water?

A: Determine the change in entropy.

Q: Draw the PV and TS Diagram of this problem. Steam at 5 MPa and 400 °C expands polytropically to 1.0 ...

Q: Sixty-two kilograms of air with enthalpy of 80 KJ/kg is mixed with another x air until the mixture i...

A: Mass of first stream of Air, m1=62 kgEnthalpy of first stream of air, h1=80 kJ/kgMass of mixture, m3...

Q: 24. The end gates ABC of a lock are 8m high and when closed make an angle of 120 deg. The width of l...

Q: 1. If A(-4,-6), B(3,–3), C(5,7), and D(x,y) are vertices of a parallelogram ABCDA, determine the coo...

Q: 6- If the original length of steal rod is equal to AL /2 with strain value is 3AL find the change in...

Q: Oxygen gas initially at 355 K and 1.50 bar undergoes the following cyclic ...

Q: A gas contained in a cylinder is compressed, the work required for compression being 9000 kJ. During...

Q: A garage door of height h and mass m is made of two identical sections ABC and CDE that are connecte...

Q: (i) The Surface tension of water in contact with air at 23°C is given as 735x10-4 N/m. The pressure ...

Q: Consider the air flow over the wing of a civil airliner flying at M. 0.85 and at an altitude of 10,0...

Q: Which of the following would depend on the process and not just on the initial and final states of a...

Q: A batch of hot tea (2.00 kg at 95°C) is thrown into a large pond, which has a temperature of 15°C th...

Q: polypropylene PP rod attached ceiling 200 mm tick , 25 mm width ,3 mm length in loaded with 30 kg . ...

A: Given dimensions of polypropylene rod Thickness = 200 mm Width = 25 mm Length = 3 mm Load = 30 kg C...

Q: The true stress beyond initial yielding

A: Given: In a linearly hardening plastic material. True stress beyond yielding is?Where, True stress i...

Q: Brine enters a circulating brine cooler at the rate of 1000 Lpm. at -8°C and leaves at -18°C. Specif...

Q: How to apply the first law of thermodynamics and Ideal gas laws to analyze behavior of gas in a cont...

A: When a closed system undergoes a complete cycle, net work done is on or by the system. the only othe...

Q: 12. A 60 lb suitcase slides from rest 5 meters down the smooth ramp. Determine the distance R where ...

Q: The resultant of the three forces shown is the force R = 200 lb. Determine P1, P2, and P3. Determine...

A: Here we considering that x,y,z components of the forces and for each direction components are adde...

Q: A submersible pump is pumping water from a well that is 200 ft of water through a 4 inch PVC pipe. T...

A: Here we have 0.01 ft per 100 ft pipe lengthSo head loss for 1 ft=0.011000 ft

Q: A hydraulic jack has a 2-inch diameter input piston and a 2-inch diameter output piston. If a 300 lb...

Q: Buckling is the critical failure mode when Euler beams are subjected to very larger compressive stre...

A: 1. false when compressive stress is less than the yield strength at this stage column will fail by b...

Q: e resultant of the moment

A: Determine the resultant of moment.

Q: An alloy of Component A and Component B, which do not react but are miscible in all proportions in ...

A: Phase Diagrams: It is an equilibrium diagram which represents the composition of constituent element...

Q: 10. If the point P(x, 1) is equidistant from the points A(2,3) and B(-3,–4), what is the value of x?...

Q: A four stage compressor works between limits of 1 bar and 115 bar. The index of compression in each ...

A: Here we have provided data from the question: X=4, p1=1 bar,p5=115 bar, n=1.28,T1=35°C=35+273 =308 K

Concept explainers

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.

Question

Fill in the Blanks:

Type your answer in the space provided after each item.
Type in your answer/s rounded off to 2 decimal places except for whole numbers. (ex: 10.67, 28, 732.40)
If your answer is 120.00 kN, just write 120 kN
Do not round off values during solving. Use the store function of your calculator or its fraction if applicable.
Include the units specified after your answer. Leave a space between the value and the unit. (ex: 6323.17 m, 73.10 lb-in, 100 kN)

An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure. Axial loads are applied at the positions indicated. If the rod should not exceed a stress in steel of 132 MPa, in aluminum of 82 MPa, or in bronze of 112 MPa:
Aluminum
A = 400 mm?
Bronze
Steel
A = 200 mm?
A = 500 mm?
2P
4P
2.5 m
2.0 m
1.5 m
1.) Find the value of P considering only the steel member.
Compression or Tension?
a. 13200 N
b. 11000 N
c. 12200 N
d. 5600 N
2.) Find the value of P considering only the aluminum member.
Compression or Tension?
a. 26300 N
b. 15000 N
c. 32000 N
d. 32800 N
3.) Find the value of P considering only the bronze member.
Compression or Tension?
a. 10200 N
b. 11200 N
c. 92000N
d. 89100 N
4.) Find the maximum value of P.
a. 10200 N
b. 11200 N
c. 8500 N
d. 5600 N

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A suspender on a suspension bridge consist of a cable that passes over the main cable (see figure) and supports the bridge deck, which is Far below. The suspender is held in position by a metal tie that is prevented from sliding downward by clamps around the suspender cable. Let P represent the load in each part of the suspender cable, and let represent the angle of the suspender cable just above the tie. represent the allowable tensile stress in the metal tie. (a) Obtain a formula for the minimum required cross-sectional area of the lie. (b) Calculate the minimum area if P = 130 kN, = 75°, and allow=80 .
Solve the preceding problem for an element in plane stress on the bottom surface of a fuel tanker (figure part a); stresses are sx= 105 MPa, sy. = 75 MPa, and ??xy= 25 MPa. Determine the stresses acting on an element oriented at an angle ?? = 40° from the x axis, where the angle is positive when counterclockwise. Show these stresses on a sketch of an element oriented at the angle ??.
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clement
Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
Two steel rods are welded together (see figure): the seam is oriented at angle ? = 50°. The stresses on the rotated element are sx1=10 ksi, sy1= -12 ksi, and tx1y1= -5 ksi. Find the state of plane stress on the clement if it is rotated clockwise to align the x3 axis with the longitudinal axis of the rods.
Solve the preceding problem for sx= 11 MPa and ??y= -20 MPa (see figure).
A plane frame with a pin support at A and roller supports at C and £ has a cable attached at E. which runs over Frictionless pulleys al D and B (see figure). The cable force is known to be 400 N. There is a pin connection just Lo the left of joint C. (a) Find reactions at supports^, C, and E. (b) Find internal stress, resultants N, V, and M just to the right of joint C. (c) Find resultant force in the pin near C.
-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
Solve the preceding problem for a plate of dimensions 100 mm × 250 mm subjected to a compressive stress of 2.5 MPa in the long direction and a tensile stress of 12.0 MPa in the short direction (see figure).
A slightly tapered bar AB of solid circular crass section and length L is supported at end B and subjected to a tensile load P at the free end A. The diameters of the bar at ends A and B are dAand dB. respectively. Determine the length of the bar if the elongation of the bar due to the load P = 45 kips is 0.02 in. Assume that E = 10,400 ksi.