A rectangular steel block is 75 mm in the x-direction, 50 mm in the y-direction and 100 mm in the zdirection. The block is subjected to triaxial loading consisting of three uniformly forces as follows:24 KN tension in the x-direction, 250 KN compression in the y-direction, and 240 KN tension inthe z-direction. If u = 0.3 and E = 200 GPa, Determine the total resulting strain in the z- direction.Note: CN is the last 2 non zero digits of your cellphone number

Answered: Image /qna-images/answer/9c9e3fbe-3581-4c8e-9dd4-0b4d6808dcc0.jpg

A rectangular steel block is 75 mm in the x-direction, 50 mm in the y-direction and 100 mm in the z direction. The block is subjected to triaxial loading consisting of three uniformly forces as follows: 241 KN tension in the x-direction, 250 KN compression in the y-direction, and 240 KN tension in the z-direction. If u = 0.3 and E = 200 GPa, Determine the total resulting strain in the z- direction. Note: CN is the last 2 non zero digits of your cellphone number

A rectangular steel block is 75 mm in the x-direction, 50 mm in the y-direction and 100 mm in the z direction. The block is subjected to triaxial loading consisting of three uniformly forces as follows: 241 KN tension in the x-direction, 250 KN compression in the y-direction, and 240 KN tension in the z-direction. If u = 0.3 and E = 200 GPa, Determine the total resulting strain in the z- direction. Note: CN is the last 2 non zero digits of your cellphone number

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

A rectangular steel block is 75 mm in the x-direction, 50 mm in the y-direction and 100 mm in the z direction. The block is subjected to triaxial loading consisting of three uniformly forces as follows: KN tension in the x-direction, 250 KN compression in the y-direction, and 240 KN tension in the z-direction. If u = 0.3 andE = 200 GPa, Determine the total resulting strain in the x- direction. %3D
A RECTANGULAR ALUMINUM BLOCK IS 110mm LONG IN THE X DIRECTION, 70mm WIDE IN THE Y DIRECTION AND 85mm THICK IN THE Z DIRECTION. IT IS SUBJECTED TO A TRIAXIAL LOADING CONSISTING OF A UNIFORMLY DISTRIBUTED FORCE OF 210 KN (COMPRESSION), 170 KN (TENSION) AND 230 KN (COMPRESSION) IN THE X, Y AND Z DIRECTIONS RESPECTIVELY. IF THE POISSON'S RATIO = 1/4 & E= 72 GPa, DETERMINE THE STRAINS IN THE X, Y AND Z DIRECTIONS. ALSO DETERMINE A SINGLE DISTRIBUTED FORCE IN THE Y DIRECTION THE WOULD PRODUCE THE SAME Z DEFORMATION AS THE ORIGINAL.
A rectangular plate is subjected to uniform biaxial stress with x = 90 MPa (tension), oy = -20 MPa (compression), and ₂ = 0. The plate has original dimensions 400 X 800 X 200 mm (x X y X z) and is made of steel with E = 200 GPa and v = 0.3. What are the strains Ex, Ey, and Ez?
2. A metal plate is .125 inch thick. What force is required to punch out a square piece 1" x 1"? The ultimate shear stress of the metal is 37,000 psi, and the ultimate tensile stress is 60,000 psi. (2 ntcl Punch Force
A mild steel bar of square cross-section 40 mm x 40 mm is 400 mm long it is subjected to a longitudinal tensile stress of 440 N/mm² and lateral compressive stress is 200 N/mm² in perpendicular directions. E = 2 x 105 N/mm², μ = 0.3. What is the approximate elongation of the bar in the longitudinal direction?
Shown is a composite plate joined together by rivets. The components consist of two tension bar plates that is ¾ X 4 inch and riveted together by two splice plates which is 0.8 X 6 inch. Each rivet has a diameter of 25.4 mm. Considering that the allowable stress for the tension bar plates and splice plates is σ=20.0 ksi, the allowable shear stress for the rivets is σ=25.0 ksi and the allowable bearing stress on the rivets and splice plates is σ=25.0 ksi. What will be the maximum permissible load P such that none of the allowable stresses will be exceeded?
1. Shown is a composite plate joined together by rivets. The components consist of two tension bar plates that is % X 4 inch and riveted together by two splice plates which is 0.8 X 6 inch. Each rivet has a diameter of 25.4 mm. Considering that the allowable stress for the tension bar plates and splice plates is o=20.0 ksi, the allowable shear stress for the rivets is o=25.0 ksi and the allowable bearing stress on the rivets and splice plates is o=25.0 ksi. What will be the maximum permissible load P such that none of the allowable stresses will be exceeded? Splice Plates a-0.75 in Bar Lc =0.80 in. Bar P d = 1.0 in. b=4.0 in. Rivets 'e = 6.0 in.
PROBLEM 6/6 F = 520 kN Determine the stress in each aluminum and steel bars after 0.2 mm F = 520 kN is applied. Note that a gap of 0.2 mm exist before the external load is Steel 280 mm applied and bars has equal distance with each other. Neglect the weight at the flat form. A = 1100 mm? E = 200 Gpa Steel Aluminum A = 2500 mm2 %3D E = 70 GPa %3D
A small aluminum alloy [E = 73 GPa] teeshape is used as a simply supported beam as shown. For this beam, a = 150 mm. The cross- sectional dimensions of the teeshape are b = 25 mm, d= 38 mm, and t=7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 490cis measured from a strain gage located at c= 9 rmm below the topmost edge of the tee stem at section 1-1. What is the applied load P? 3P Strain gage d a a H Answer: P = i
!! Show Complete & Detailed Solution w/ FBD !!The bronze bar 3 m long with a cross-sectional area of 350 mm^2 is placed between two rigid walls. At a temperature of –25C, there is a gap  = 2.5 mm, as shown in the figure. Find the temperature at which the compressive stress in the bar will be 30 MPa. Use α = 18.0 x 10–6 /C and E = 80 GPa.
A steel rod with a cross-sectional area of 188 mm2 is stretched between two fixed points. The tensile load at 23°C is 6,332 N. What will be the stress at -15°C ? Assume a = 11.7 x 10-6 m/(m.°C) and E = 198 GPa. Answer must be in MPa.
Determine maximum shear stress