21. An ideal Schottky junction is formed by p-Si with Na = 101º cm and an unknown metal. The results of the C-V measurements of this structure together with a straight-line fit are shown in the figure. Determine the work function of the metal. 1/C ? Answer: 4.73 eV - 0.2 V Show the workings to get to the provided answer please

21. An ideal Schottky junction is formed by p-Si with Na = 101º cm and an unknown metal. The results of the C-V measurements of this structure together with a straight-line fit are shown in the figure. Determine the work function of the metal. 1/C ? Answer: 4.73 eV - 0.2 V Show the workings to get to the provided answer please

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where R1 and R2 are the resistances at temperatures T1 and T2, respectively, and is known as the temperature coefficient of resistance. If a copper wire has a resistance of 55 at 20C, find the maximum permissible operating temperature of the wire if its resistance is to increase by at most 20. Take the temperature coefficient at 20C to be =0.00382.
Figure Q2(a) shows the characteristic curve of a Zener diode. Analyse the characteristic curve to identify the approximate minimum Zener current Izk(min) and the approximate Zener voltage, Vz at IZK. -10 -9 -8 -7 -6 -5 -2 -1 Vz (V) + 1 3 4 6 7 8 Iz (mA) Figure Q2(a) Analyse the circuit in Figure Q2(b) to identify the minimum input voltage required to keep the diode in Zener region based on the values of the minimum Zener current and the approximated Zener voltage found in Question 2(a). R 1k2 VIN Figure Q2(b)
Using drawing and Explanation. Effect of light: What will happen if you shine a light on three parts of the p-n junction. Show the effect of light separately on p-si, n-si, and depletion regions. ww.
The formula used to fit ILED versus VLED was Y = a (1-e^-bx). Compare this equation to the shockley ideal diode equation. what is the parameters a and b?
Where is the pn junction? What is n+ region and the p-type substrate?
A diode circuit is given in the below figure, in which two diodes are connected in series and their saturation currents are Is1 =10-¹6 A and Is2 =10-¹4 A. If the applied source voltage is 1 V, calculate the currents IDI and ID2 and the voltage across each diode VDI and VD2. IDI Ī Vpl + D₂ VD2
As shown is a positive parallel clipper circuit which has an input voltage of E=t5V. The negative output voltage is to be -4.5V when lo is 5mA. Assume ideal diode model approximation. Determine the value of R1 in ohms. Note: Write only the numeric value of the answer, round to 4 decimal places. No need to include the unit. R, +E ww Output Input D, -E -(E-1,R,)
uO 9:.0 A docs.google.com * ZAIN IQ l. Q3/B: Assume an ideal diode model for all the diodes in the circuit below. calculate voltages and currents through D1 and D2 9kQ 1N1199C R2 D1 18KQ 1N1199C D3 1N1199C V2 =12 V R3 1kQ R4 5kQ 1.22 V 11 mA 0.5 A O VD1 ID1 VD2 ID2 صفحة 4 من 6
In the figure given we have u(t)=10. cosot [V]. We assume the diodes and the A-meter (A) to be ideal. A u(t) a) Plot the waveform of the current flowing through the A-m in scale. b) What is the reading of the A-m, if it is moving-coil type? c) What is the reading of the A-m, if it is moving-iron type? d) Calculate the power factor of the WHOLE structure. R1 1 R2 102
In the circuit given in the figure, find the current passing through the diode in mA since R1 = 4.95Kohm, R2 = 2.50Kohm, R3 = 1.69Kohm, R4 = 5.44Kohm, VCC = 13.00V and the diode is silicon?
Q1 Assume that each diode has a turn-on voltage 0.7V in the circuit shown in Figure Q1. By using the constant voltage drop model: 1kN D1 D2 2kN 4k2 6V 3V 4V Figure Q1 a) Show that it is not possible that D1 is on and D2 is off. (Hint: show a contradiction) b) Show that both D1 and D2 are on.
Using 2nd approximation for the circuit shown, assuming that the diode used is a silicon diode, determine the currents ID1, ID2 and current through R2. Finalize answers as follows: ID1= Ir2= ID2= R2 D1 3.3 kQ BAT1 D2 20 V R1 5.6 kn