ニエニ20.0° 37.0° 20.0° the

Q: A uniform drawbridge must be held at a 41.0° angle above the horizontal to allow ships to pass…

A:

Q: A wrench 0.3 meters long lies along the positive y-axis, and grips a bolt at the origin. A force is…

A:

Q: 28. The fishing pole in Figure P10.28 makes an angle of W 20.0° with the horizontal. What is the…

A: Given:  Force, F = 100 NRadius, r = 2 mFind: The torque exerted by the fish about an axis…

Q: A 100 N force exerted at the end of a 0.50 m long torque wrench supplies a torque of 20 N·m. What is…

A:

Q: F = N-m 124 N at an angle 37.0° below the horizontal? The force is applied at a point L = 2.02 m…

A: Step 1:

Q: An engineer applies a force of magnitude F=15 N to the tip of a vertical lever. The force has an…

A:

Q: A Fx

A:

Q: A wrench lies horizontally, so that the nut to be twisted is on the right and the arm is on the…

A: It is given that the nut is twisted on the right  and arm to the left. Hence the following diagram…

Q: A horizontal force of 10.1 N is applied at an angle of 34.9 degrees to the knob of a 71.1 cm wide…

A: If the line of axis of a force passing through the axis of the door or parallel to the axis of the…

Q: When tightening a bolt, you push perpendicularly on a wrench with a force of 165 N at a distance of…

A: using formula of torque,

Q: A 2-m long bar makes an angle of 30° with the horizontal. A vertical force of 40 N is applied 0.4 m…

A:

Q: Three children are balanced on a  a seesaw as shown.  The fulcrum is located below the center of…

A: Given information: The fulcrum is located at the center of mass. The length of the see-saw is (l) =…

Q: A street light hangs from a traffic pole as shown in the figure. The uniform aluminum pole AB is 7.2…

A:

Q: 1. Calculate the torque about the origin produced by a constant force of (5î + 4k) N on a particle…

A: Given Data: The force acting is, F⇀=5i^+4k^ N. The distance is, r⇀=i^-2k^ m. The expression for…

Q: 350 250 A fish has been hooked amd pulling a fisherman's 192 cm long fishing rod as shwon in the…

A: Given data: The pulling force by fish is F=224 N. The length of rod is l=192 cm.

Q: By using |t| = Ir| |F| sin 0, find the magnitude of the torque about O produced by each force shown.…

A: using the formula of torque and right hand rule for direction of torque

Q: A dental bracket exerts a horizontal force of 66.2 N on a tooth at point B in the figure. What is…

A:

Q: In opening a door, a 49.3 N force is applied as shown in the figure below. Find the torque produced…

A:

Q: What is the torque about the pivot point shown by the 8.00 N force, in N-m? (Pay attention to the…

A:

Q: The 20-mm-diameter A-36 steel shaft is subjected to the torques shown. 80 Nm 20 Nm 30 Nm 800 mm 600…

A:

Q: A fisherman has a fish hooked on his line. At first, the pole is horizontal, as shown on the left.…

A: torque is given by t = R * F sinθ Here,t = torque, R =Distance between Force and point of holding…

Q: In the figure, the rectangle is a uniform block of mass 259. It is 1 meter wide and 1.21 meters…

A: In the limiting case , when the block is just about to tip over , the entire rectangular block rests…

Q: What happens to the torque due to the tension? Is your result consistent with the formula τ = R × f?…

A:

Q: The boom of a crane is 19.56 m long and is inclined 28.4 degrees from the horizontal. A bucket of…

A: L= 19.56 m  Angle is 28.4°  M= 3292.29 kg

Q: To tighten a bolt, you push with a force of 85 N at the end of a wrench handle that is 0.35 m from…

A:

Q: The 5.0 kg, uniform, horizontal rod is seen from the side. What is the gravitational torque about…

A:

Q: trap door, of length and width 1.85 m, is held open at an angle of 65.0° with respect to the floor.…

A:

Q: A wheel is rotating clockwise as shown (by the arrow). Its rotation axis coincides with the x-axis.…

A: Torque vector 5 will cause the wheel to speed up. Vector 5 is curling around the wheel in the…

Q: Sketch the following positions and forces F. Use the cross product of the unit vectors to calculate…

A:

Q: a b Ꮎ F

A:

Q: Two employees are walking through a rotating door, as shown in the figure below. The woman on the…

A: The net force acting on an object is equal to the mass times acceleration of the object. If the net…

Q: The figure below shows forces acting at various points on a metal rod. The angles α = 40°, B = 25°,…

A: (a) For an axis through O perpendicular to the page, the net torque is -30.6 Nm in the…

Q: The fishing pole in the figure below makes an angle of 20.0° with the horizontal. What is the…

A: Given,  L = 1.80 m  F = 108 N at an angle 37.0° below the horizontal The fishing pole in the figure…

Q: The diagram above shows a force acting at an angle on the end of a bar. The force has a magnitude of…

A: Force, F = 11.5 NLength, L = 1.2 mTorque, τ = ?

Q: The diagram above shows a force acting at an angle on the end of a bar. The force has a magnitude of…

A:

Q: A 20-cm-long wrench is used to tighten a nut. The wrench handle is pulled at 35° from the…

A:

Q: A 100 N uniform beam with a length of 3.0 m and supported at the middle is in equilibrium. What is…

A: The torque is given by the product of force and the perpendicular distance.

Q: The large quadriceps muscle in the upper leg terminates at its lover end in a tendon attached to the…

A:

Q: A square, 0.144 m on a side, is mounted so that it can rotate about an axis that passes through the…

A: Side of the square, s = 0.144 mForce, F = 10.5 NTorque is the rotational equivalent of force and is…

Q: A5N force is applied to a doorknob 0.72 m from the hinge as illustrated in the figure below. What is…

A: ACCORDING TO QUETION- A FORCE IS APPLING ON A DOORKNOB WHICH IS 57 DEGREE FROM ITS HINGE GIVEN THAT…

Q: Torque is a vector. Explain how you find both the magnitude as well as the direction of the torque…

A: The technique to combine two vectors is to use the vector or cross product, which produces a vector…

Torque

Torque is the rotational equivalent of linear force in physics and mechanics. Based on the course of study, it is also known as the moment of force, rotational force, or turning effect.