The figure below shows forces acting at various points on a metal rod. The angles α = 40°, B = 25°, y = 17°. The length.l = 4.6 m. Find the net torque (in N · m) on the rod about the following axes.25 Nαof 1230 N10 N(a) an axis through O perpendicular to the pagemagnitudedirection---Select---N⚫ m(b) an axis through C perpendicular to the pagemagnitudedirection---Select---N⚫mO

(a) For an axis through O perpendicular to the page, the net torque is -30.6 Nm in the…

Answered: The figure below shows forces acting at…

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A 3.0-m rod is pivoted about its left end. A force of 6.0 N is applied perpendicular to the rod at a distance of 1.2 m from the pivot causing a ccw torque, and a force of 5.2 N is applied at the end of the rod 3.0 m from the pivot. The 5.2 N is at an angle of 25 degrees to the rod and causes a cw torque. What is the net torque about the pivot? Choose – 6.3 Nm –1.7 Nm 0.6 Nm – 0.6 Nm
A bar of length 3.00 m is hinged at one end and experiences a force of 8.00 N at the other end. The torque applied is 10.0N⋅m. What must be the angle between the line of force and the extended line of the bar ϕ?
A bar on a hinge starts from rest and rotates with an angular acceleration a = 13 + 7t, where a is in rad/s? and t is in seconds. Determine the angle in radians through which the bar turns in the first 4.53 s. 226 Your response is within 10% of the correct value. This may be due to roundoff error, or you could have a mistake in your calculation. Carry out all intermediate results to at least four- digit accuracy to minimize roundoff error, rad
What torque applied to the cylinder of prob 1220 will raise the weight with an acceleration of 13 ft/sec? What will be the total bearing reaction?
A pipe system consists of three pipes with lengths L₁ = 1.75 m, L₂ = 0.800 m, and L3 = 2.55 m. A plumber pulls on the end of the pipe system, at the point P, with a force Fp = -21.0 Ni+ 42.5 Nj + 29.0 Nk. What is the torque 7 due to Fp about the origin? Enter your expression using ijk unit vector notation. 0 N-m 21
2. Let F = 4 i -6 j + 2 k and Let r = 3 i -3 j - 5 k. Find the torque in both Cartesian and polar coordinates. (Find Torque by cross product, find the magnitude of the torque, find the SOLID angle theta and phi since the vector will be in 3 dimensions.) ____________________________________________________________________________________________________________________________________________________________________________ If you could clearly circle the answer I need, that would be great! Thanks!
When opening a door, you push on it perpendicularly with a force of 55.0N at a distance of 0.850m from the hinges. What torque are you exerting relative to the hinges?
A particle is located at the point with coordinates (0, 3, 6) m, and the force acting on it is F= (3i +2) N. What is the torque about the point having coordinates (0, 2, 4) m? (Hint: %3D Determine the vector r first in t=rx F) Lütfen birini seçin: a. 4i-6j+3k Ob.-di+6j-3k C-21+3j+12k d. 21-3j-12k e. 11
Question 16 my m, Two blocks are joined by a pulley system (see Figure). The pulley is a solid disk of mass 0.5 kg and radius 179 mm. Assume that the pulley rotates smoothly. If mass 1 is 4.4 kg and mass 2 is 15 kg, what is the angular acceleration of the disk? HINT: the tensions in the horizontal and vertical portions of the rope are not equal. (PUHQ1629)
Find Torque ofN, the torque about point P due to the normal force. Express your answer in terms of N and any of the other quantities given in the figure.
A wheel of inner radius r, = 14.6 cm and outer radius r, = 35.0 cm shown in the figure below is free to rotate about the axle through the origin O. What is the magnitude of the net torque on the wheel due to the three forces shown? (Assume F, = 4.20 N, F, = 6.20 N, and F, = 13.0 N.) N. m F2 F1 45.0°
The 25 N force F is applied to a corner of the rectangular plate of sides a = 0.50 m, b = 0.70 m. The angle θ is 37deg. a) Find the torque on the plate about i) the corner A, ii) the corner B, and iii) the corner C. Give both the magnitude and direction (clockwise or counterclockwise) in each case.

Recommended textbooks for you

College Physics

Physics

ISBN:

9781305952300

Author:

Raymond A. Serway, Chris Vuille

Publisher:

Cengage Learning

University Physics (14th Edition)

Physics

ISBN:

9780133969290

Author:

Hugh D. Young, Roger A. Freedman

Publisher:

PEARSON

Introduction To Quantum Mechanics

Physics

ISBN:

9781107189638

Author:

Griffiths, David J., Schroeter, Darrell F.

Publisher:

Cambridge University Press

College Physics

Physics

ISBN:

9781305952300

Author:

Raymond A. Serway, Chris Vuille

Publisher:

Cengage Learning

University Physics (14th Edition)

Physics

ISBN:

9780133969290

Author:

Hugh D. Young, Roger A. Freedman

Publisher:

PEARSON

Introduction To Quantum Mechanics

Physics

ISBN:

9781107189638

Author:

Griffiths, David J., Schroeter, Darrell F.

Publisher:

Cambridge University Press

Physics for Scientists and Engineers

Physics

ISBN:

9781337553278

Author:

Raymond A. Serway, John W. Jewett

Publisher:

Cengage Learning

Lecture- Tutorials for Introductory Astronomy

Physics

ISBN:

9780321820464

Author:

Edward E. Prather, Tim P. Slater, Jeff P. Adams, Gina Brissenden

Publisher:

Addison-Wesley

College Physics: A Strategic Approach (4th Editio…

Physics

ISBN:

9780134609034

Author:

Randall D. Knight (Professor Emeritus), Brian Jones, Stuart Field

Publisher:

PEARSON

SEE MORE TEXTBOOKS