2.5 CM7.5 cm-5 cm-370 C--66 CConcrete clInderblockk = 0.76 W/m.CBull dingbrickk = 0.69 W/m.CT1-T2Figure Q4Fir k = 0.11 W/m.CYellow plnek = 0.147 W/m.C Q4:Consider the heat flow in one direction (x-axis) through the composite wall shown inFigure Q4. Draw the thermal circuit then determine T1 and T2, and the heat flux (q, W/m2),knowing that the thermal conductivity of the Fir (0.11 W/m.°C), the concrete cinder block(0.76 W/m.°C), the building brick (0.69 W/m.°C) and the yellow pine (0.147 W/m.°C).Consider also the concrete cinder block and building brick sections are of equal thickness.

Given, Concrete cinder block=0.76 W/m°C Building brick=0.69 W/m °C Yellow pine=0.147 W/m°C

Answered: 2.5 cm 7.5 cm- -5 cm- 66 C 370 C-…

Engineering

Civil Engineering

2.5 cm 7.5 cm- -5 cm- 66 C 370 C- Concrete cInder block k = 0.76 W/m.C = 0.11 W/m.C aujd

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel tube with 5 cm ID, 7.6 cm OD and k=15W/m °C is covered with an insulative covering of thickness 2 cm and k 0.2 W/m °C. A hot gas at 330° C with h = 400 W/m2oC flows inside the tube. The outer surface of the insulation is exposed to cooler air at 30°C with h = 60 W/m2oC. Calculate the heat loss from the tube to the air for 10 m of the tube and the temperature drops resulting from the thermal resistances of the hot gas flow, the steel tube, the insulation layer and the outside air.
A concrete wall has a thermal resistance of 0.095 K/W. There is a glass window in the concrete wall with a thermal resistance of 0.046 K/W. What is the total thermal resistance for the whole configuration (wall+ window) (K/W)? O A. 0.1410 B. 32.2654 C. 0.6738 OD. 0.0310 OE. None of them.
Inside a wall measuring N/Sx N /3m, there are 2(glass thickness lcm) single-glazed windows measuring 1.5 m x 3 m with a heat transfer coefficient of K there is a window. The ambient temperature on the inside of the wall is N20C, the outdoor temperature is - N3 oC, the coefficients of external and internal convection are aş= N W/m2 C, aic = N/3 W/m2 C is. The wall is from the outside to the inside, 0.1N cm. the outer plaster with a thickness of k= 0.3N W/ moC, with a thickness of N/ 2 cm k = 0.8 W/moC reinforced concrete is composed of 1 cm thick k= 0.6 W/m oC gypsum honey inner plaster.Find out the total heat loss. To reduce heat loss by 80%, k= How many cm of insulating(styrofoam) material with an oC of 0.001(N+N2 )W/m should be N=26 used(calculations will be made for single and double glazing. My greatest achievement please heap the required amount of flow before and after it is made N2=9 N3=119
Do a quick calculation of the thermal conductance (U value) across a cavity wall consisting of:1. Outer skin 220mm brickwork (North facing, exposed aspect) 2. 20mmcavity 3. Inner skin of 10mm plasterboard Compare this with the worked example of an insulated brick veneer wall in the worked example. Show your working.
Determine the thermal conductivity of brickwork of cavity wall comprising 220mm brickwork, 12mm plaster, 80mm cavity, k values are plaster 0.6W/m°C, cavity resistance 0.18m"C/W, internal resistance 0.12m²"C/W, external resistance 0.06 m"C/W. U value of the wall is 1.78.
Q- To complement the construction Q- What is the correct Sentence of a wall or to connect a wall to be scientifically? constructed with a previously Thermal insulation value of brick constructed wall specially If the wall units wall was a measure of the is to be connected vertically when capacity of the wall to retention heat between inside and outside the building and the greater the value of the coefficient the lower O Non of them the amount of heat leaking. The previously built wall each brick is left on the head so that it will Thermal transmittance coefficient of brick units wall was a measure of down away from the face of the wall about quarter brick and this works the ability of the wall to escape heat between inside and outside the done between row and row. building and the greater the value of It is left without completion, and each row is an apostate from the row under of it about a quarter or the coefficient the lower the amount of heat leaking. O All answers corrected half…
Calculate the thickness of the masonry wall having thermalconductivity of 0.75 W/mK if the heat transfer is to be 80% of theheat transfer through a composite structural wall having athermal conductivity of 0.25 W/mK and a thickness of 100mm.Assume that both walls are subjected to same surfacetemperature.
12. Thermal efficiency using temperature values 13. Thermal efficiency using rc and k values
Improving the insulation of the building lead to decreasing the conduction losses. Select one: True False
100°? air flows through a round aluminum tube of ID 60mm and OD 80mm at 4 ?? .The tube is covered in 5mm thick fiberglass insulation. The tube is surrounded by RT air flowing at 5?? over the outside of the insulation. What is the heat rate through the wall of the tube? Assume that the air temperature is constant throughout the tube. Note: RT is 25 celsius
Air at 25 ° C blows over the hot steel plate whose surface temperature is maintained at 150 ° C. The plates are 50 cm x 40 cm in dimensions and 2.5 cm thick. The convection heat transfer coefficient on the upper surface is 20 W / (m² ° C). The thermal conductivity of steel is 45 W / (m ° C). Calculate the hourly heat loss from the plate surface. a. heat loss per hour = kJ. Answer b. If the reverse side surface temperature is maintained, determine the hourly heat loss incurred = kJ.Answer
Help your customer to calculate the heat losses through a composite wall that includes an 8-mm-thick hardwood siding, 40-mm by 130-mm hardwood studs with glass fiber insulation (paper faced, 28 kg/m3 ), and a 12-mm layer of gypsum (vermiculite) wall board as shown. The wall is 2.5 m high by 6.5 m wide. - 20 °C Wood siding Stud 130 mm Insulation Wall board 21 °C 40 mm Figure 1: The top view of thecomposite wall.