1. Water is flowing in a trapezoidal channel at a rate of Q20 m'/s. The eritical depth y for such a channel must satisfy theequation0 =1Bwhere g = 9.81 m/s², Aç = the cross-sectional area (m³), and B =the width of the channel at the surface (m). For this case, the widthand the eross-sectional area can be related to depth y byB- 3+y and Ac = 3y -Solve for the critical depth usinga. Bisection Methodb. False Position MethodUse initial guesses of XI = 0.5 and Xu = 2.5, and iterate until theapproximate error falls below 1% or the number of iterationsеxceeds 10.

Answered: Image /qna-images/answer/23e22351-a89f-43e5-8320-dbe01a285d73.jpg

Solve for the critical depth using a. Bisection Method b. False Position Method Use initial guesses of XI - 0.5 and Xu - 2.5, and iterate until the approximate error falls below 1% or the number of iterations exceeds 10.

Solve for the critical depth using a. Bisection Method b. False Position Method Use initial guesses of XI - 0.5 and Xu - 2.5, and iterate until the approximate error falls below 1% or the number of iterations exceeds 10.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 2. Solve for the slope and deflection at point C using Area-Moment Method. Assume point B to D has…

A: Overhanging beam with udl of intensity 100 lb/ft and moment, M = 1200 lb-ft.EI is twice between…

Q: USING CONJUGATE BEAM METHOD SOLVE THE FOLLOWING P P a b b Determine the slope (in rad) at 2.36m from…

Q: Problem 1. Determine the following unknowns on the beam shown below using Double Integration Method.…

A: Given Beam condition From Equilibrium equations ∑FY=0 RA+RD=36×7+39+22+02×6=357kN ∑MZ=0 taking…

Q: Problem 1. Use virtual work method and determine the following unknowns on the frame shown below.…

Q: Determine the values of 0A and vA. Clearly indicate both magnitude and direction. Answer: 0 = 135…

A: According to given dataWe need to calculate the asked Values which is solved below

Q: Problem 1: Using the Double integration method, find the slope at x = 5m and deflection at x = 7.0m…

Q: For the following steel frame (E = 200,000 MPa; l = 500 x 106 mm4), use the virtual work method to…

A: E= 200,000 MPa I= 500×106 mm4 To determine- a) The horizontal displacement at point B b) The…

Q: 35KN/m 180 kN 15 kN/m B C-2 5 m m 4 m El = constant E = 70 GPa I = 2,340 (10) mm

Q: Using double integration method (DIM), determine the slope and deflection at point C. consider El as…

Q: Problem 1 80 kN A Using the Virtual Work Method, and assuming El constant, 3 m. 3 m a) Determine Ac…

A: Load = 80KN

Q: 30 kN 50 kN to B D A 1 m 3 m 2 m Figure P-403

Q: USE DOUBLE INTEGRATION METHOD. From the given determinate beam, which of the following provides the…

Q: ● Determine the SLOPE AND DISPLACEMENT at point A. TAKE E = || GPA. THE VALUE OF "I" CAN BE SOLVED…

Q: For the frame shown in the figure, determine the slope at coc using Castigliano's Theorem. E =…

Q: Solve using Double Integration Method. Assume EI as stated in the picture. Show your solution…

Q: PROBLEM: Use the method of double integration and moment-area theorem to solve for the following: a.…

Q: INSTRUCTION: Solve the following problems. Show your solutions. If the answer is not exact, round it…

Q: Q1A- the major formula in hardy-cross method is Darcy-weisbach equation * a) True b)…

A: Hardy-cross method: Hardy-cross method is derived from the moment distribution method. This method…

Q: This is a question from slope stability bishop method Please Note i am not asking for the entire…

A: Data given Bishop Circle method of analysis

Q: Solve the following armature using the virtual work method, Taking into account E = 29x103 K / in2,…

A: We have used the following data 1 plug 2 = 1 inch2 1 pies= 1 feet E= 29×103 ksi

Q: Interpolate between In (4) = 1.386294361 and In (8) = 2.079441542. Also, compute the percent…

A: Given Ln(4) =1.386294361 Ln(8) = 2.079441542

Q: Deflection of a uniform beam Figure 3(a) shows a uniform beam subject to a linearly increasing…

A: A simply supported beam with uniformly varying loadequation of deflection substitute in the above…

Q: Problem 1. Use virtual work method and determine the following unknowns on the frame shown below.…

A: Given, I=800×106 mm4E=200 GPa

Q: GIVEN: f(x) = cos(x)-√4-x² Using NEWTON'S METHOD, determine new estimate after 2nd iteration. ε =…

A: Asked: To determine the root of the given function after second iteration using Newton's formula.…

Q: Use Crank-Nicolson method to solve the following PDE a²u ди +b= Эх = au at Over 0≤x≤1 and 0≤t≤3,…

A: Approach to solving the question: the image sequence is 3-2-1....or if seen from reverse then 1-2-3…

Q: Problem 1. Use slope-deflection method and determine the following unknowns on the frame shown…

Q: Consider the beam shown in (Eigure 1). Assume the support at A is a pin and C is a roller. Take E =…

A: Find slope and deflection at B using virtual load method

Q: Problem 1. Use virtual work method and determine the following unknowns on the frame shown below.…

Q: Find the estimated value for the parameter lembda in Poisson distribution using moment method...?

A: Lembda in poison's distribution is defined as the average rate of expected value or variance or…

Q: Problem 1. Use slope-deflection method and determine the following unknowns on the frame shown…

Q: Give me both answers

A: Draw free body diagram

Q: The next iterative value of the root of (x^2)-4 using the Newton-Raphson method, if the initial…

A: To determine the next iterative root of a given function for a given initial guess using…

Q: Consider the beam shown in (Figure 1). EI is constant. Assume that EI is in kN - m². Suppose that M…

A: given dataBeam is givenFindslope to the left of Bslope to the right of Bdisplacement at D

Q: Consider the beam shown in Figure 1). El is constant. Assume that El is in kN-² Use the principle of…

A: The unit-load method is a technique that will help us to quantify displacements and rotations of the…

Q: e l = 800 x 106 mm4 and E = 200 GPa. Show complete and organized solution. Round-off your answ two…

A: In equilibrium, the virtual work of forces applied to a system is zero, and Newton's laws state that…

Q: USE DOUBLE INTEGRATION METHOD. From the given determinate beam, which of the following provides the…

Q: using the method in analysis of beam deflections and rotations (CONJUGATE BEAM METHOD), find the ff.…

A: Given, Young modulus E is 80 GPa Moment of inertia I is 100×106 mm6

Q: Mannings equation can only be used to find one value of velocity at a time. True False

A: Given data in question Mannings equation To find out Is the given statement true or false Note V =…

Q: C. Consider the function y = x³ 1. Draw the function and write an expression to represent an upward…

A: Step 1: Step 2: Step 3: Step 4:

Q: Determine the vertical deflection of point C in the figure shown below. Use virtual work method. All…

Q: Using double integration method, determine the value of the constant, C2 for segment AB. M=400 kN.m…

Q: A Bisection method is applied to find the root between point A to B. Given a function x* -x = 10-.…

Q: Using double integration method, solve for the slope and deflection at point A. Given: E= 210 GPa I=…

A: Using double integration method, solve for the slope and deflection at point A. Given: E= 210 GPa I=…

Q: Use virtual work method and determine the following unknowns on the frame shown below. Use I = 800 x…

Q: Problem I. Given the figure, determine the following unknowns using constant El. 30 kN/m a. Reaction…

Question

1. Water is flowing in a trapezoidal channel at a rate of Q
20 m'/s. The eritical depth y for such a channel must satisfy the
equation
0 =1
B
where g = 9.81 m/s², Aç = the cross-sectional area (m³), and B =
the width of the channel at the surface (m). For this case, the width
and the eross-sectional area can be related to depth y by
B- 3+y and Ac = 3y -
Solve for the critical depth using
a. Bisection Method
b. False Position Method
Use initial guesses of XI = 0.5 and Xu = 2.5, and iterate until the
approximate error falls below 1% or the number of iterations
еxceeds 10.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Use double integration method
dy dx Find by implicit differentiation if sec(ry) = 6y. dy dx
For the frame shown below, determine the horizontal displacement at C. Assume that AB and BC segments have same EI values. Leave your answer in terms of EI. Explain how you will determine the vertical displacement at C using the method of virtual work. 6 kN/m B L 3 m -2 m 12 kN
Kindly use Double Integration Method to solve the problem.
the next iterative value of the of x? - 4 = O using secant method, if the initial guess is 3 and 4 2.2857 2.3123 2.1213 2.2556
Solve using Methods of solution to High Order Differential EquationOr using Laplace Transform
Use Castigliano's Theorem to determine the slope at joint B in radian. I 2340x10®mm and the E = 200 GPa. Let Q =14kN/m., L=9 Answer in 2 decimal places A B 2L L/2 Q L/2 |D
Please solve the question in the picture, I know it's two region but draw the FBD WHEN YOU'RE DERIVING THE MOMENT FUNCTION FOR AB AND BC
test for the linear independence or independence of the following functions in all intervals using wronskian: e^x, cosx, sinx
Choose the best answer
Calculate the slope at C using ONE of these methods: double integration method, area-moment and conjugate beam method. Also, determine the deflection at C using EITHER virtual work method or Castigliano theorem method. Set P = 10 kN, w = 2 kN/m, support A is pin and support B is roller. W. C 1 m 1m Use the editor to format your answer
Problem 1. Determine the following unknowns on the beam shown below using Double Integration Method. Consider 150 mm x 150 mm section and E = 200 GPa. Show complete and organized solution. Round-off your answers to two decimal places. a. Deflection at point B in mm. b. Deflection at point E in mm. c. Slope of the elastic curve at point D in degrees. А.) 3.30m В.) 21.00 kN/m С.) 40 kN D.) 72 kN/m |c kN b kN/m d kN/m BỊ DO IE 4 m 3 m 3 m