H.W(2):Water flows steadily from a large tank through a pipe that splits into two smaller pipes as shown in fig. Determine the flow rate from the tank and the pressure at point (1). (0) 3 m (2) 7 m 0.03 m 0.05 m (3) Ans: Q = 0.00910- m3 ,P =57.9 kPa (1) 0.02 m

H.W(2):Water flows steadily from a large tank through a pipe that splits into two smaller pipes as shown in fig. Determine the flow rate from the tank and the pressure at point (1). (0) 3 m (2) 7 m 0.03 m 0.05 m (3) Ans: Q = 0.00910- m3 ,P =57.9 kPa (1) 0.02 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Calculate the surface tension of the fluid (SG = 8.6) in the capillary tube below: Зтт h = 2mm e =…

Q: (Laminar flow) A fluid flows through two horizontal pipes of equal length which are connected…

A: To find diameter of second pipe

Q: Air (1.23 kg/m³) flows past an object in a 2-m-diameter pipe and exits as a free jet as shown in the…

A: Given, ρ = 1.23 kg/m3 D = 2 m NOTE : As per guidelines, first 3 parts are solved. Request you to…

Q: Water flows through a pipe at 144 L/s that changes gradually in diameter from 188 mm at point A to…

Q: ÞA P9 UA 2g =? = 7m DA=0.2m ZA=10m Akım borusu DB=0.3m 24B 2g =? Þs pg =? ZB=15m ds (v. dQ. dt) =…

Q: Determine the value of hin meters indicated in the

Q: Q2- Find the gage pressure (A) in the water pipe shown in fig. Nots: the density of water -1000kg/m'…

A: To find pressure at point A

Q: 1 (

Q: C) In a cylinder-piston arrangement shown (D₁ = 100 mm), the piston is moving downwards at Vp = 0.5…

A: step 1-

Q: (Laminar flow) A fluid flows through two horizontal pipes of equal length which are connected…

A: Total length of both pipe=2l To find diameter of second pipe

Q: Problem 1: Energy Equation Assuming steady flow of an ideal incompressible fluid, find the pressure…

A: g=32 ft/s2at point Adia of pipe=12 in=at point Bdia of pipe=6 inpressure head ()=2 ftvelcoty (vB)=8…

Q: (a) determine pressure at Section-2. (b) the volume rate of flow in m³/s.

Q: Shown in figure, A pump discharged 0.05 cu. m/sec. water from a 220 mm suction pipe and delivers it…

Q: a.) Determine the pressure difference between the two vessels when the difference in the levels of…

Q: Bernoulli's theorem demonstration: D ° d Water is flowing through the above venturimeter (D=22 mm…

A: Given Diameters 22 and 15 mmDischarge 0.6 l/sTo find out Pressure difference

Q: Water flows from a large tank through a large pipe that splits into two smaller pipes as shown in…

A: Given : To Determine :

Q: 3. Oil of Gs=0.80 is flowing in a pipe 8 inches diameter with a mean velocity of 12 ft/sec. The…

Q: What height of a column of special gage liquid (sp gr 1.85) would exert the same pressure as a…

A: Heavy liquid requires less depth We will use formula of pressure in terms of depth of fluid.

Q: With the chamber-pipe system in the figure, the ideal fluid (water) taken from the infinitely sized…

A: Given:- The chamber-pipe system is given The fixed diameter of BCDEF pipe = 40 cm The elevation of…

Q: Water flows through a pipe at 15 L/s as shown. If the gage pressure of 12.5 kPa, 11.5 kPa and 10.3…

A: The values and figure given in the question are as follows: Discharge through pipe(Q)=15 L/sec…

Q: In the situation shown in the figure, the water flows from the upper tank A to the lower one tank B.…

A: Answer Apply Bernoulli's equation at point A and B PAγ+VA2γ+zA = PBγ+VB2γ+zB+hL PA and PB are…

Q: Q1: A pressure of 10 kPa, gage, is applied to th surface of water in an enclosed tank as showi in…

A: to find actual discharge

Q: The figure shows an inlet and outlet connected to a motor. If the pressure at A is 6.25 MPa and the…

A: step 1-

Q: Q1) Determine the difference in pressure between pipe A and pipe B. Kg m PFresh water = 1000 Kg m³…

Q: What is the gauge pressure at point P in the figure? Assume g = 10 m/s² ¥ Water Immiscible liquid of…

A: Given data- Water depth hw=0.8 m, Immiscible liquid depth hl=1 m, Specific gravity of liquid G=1.6,…

Q: Water flows from a tank through 160 feet of 4 inches diameter pipe and then discharges into air as…

A: Given data, n= 0.013 Discharge, Q= 12 cfs Length of pipe = 160 ft Diameter of pipe = 4 in To find…

Q: A 3m Oil: 2m S.g. = 0.9 %3D (F), B 2m Water (F,

Q: As shown in the figure, water enters and exits a U-shaped piece of pipe located in the horizontal…

Q: Bernoulli. Water is siphoned from a large tank filled to a depth of 3m using a tube (Dr=0.6 cm) with…

A: Bernoulli's theorem : In fluid dynamics, Bernoulli's theorem describes the relationship between…

Q: Determine the depth z (in feet) of oil in the tank. b)Determine the differential reading, h (in…

Q: B: A closed cylindrical tank filled with water has a hemispherical dome and is connected to an…

A: Asked: To determine the pressure in pipe B and the pressure head, in millimeters of mercury, at…

Q: In fig. if H= 88 inches, the difference in pressure =---?(the fluid is water) Piezometer (static)…

Q: 2.26 For the inclined-tube manometer of Fig. P2.26 the pres- sure in pipe A is 0.8 psi. The fluid in…

Concept explainers

Storm Sewers and Detention

The storm drains system transports rainwater or stormwater and other runoff from roads, parking lots, and roof downpipes directly to nearby creeks, rivers, or the sea without any treatment.

Question

WARH ALANBIYAA
University of Warith Al-Anbiyaa, College of Engineering, Civil Engineering Department.
VERSITY OF
H.W(2):Water flows steadily from a large tank through a pipe that splits into two smaller pipes
as shown in fig. Determine the flow rate from the tank and the pressure at point (1).
2017 a
(0)
3 m
(2)
7 m
0.03 m
0.05 m
(3)
m3
,P =57.9 kPa
f (1)
Ans: Q
= 0.00910
0.02 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the flow in lps on the orifice between the 2 tanks shown below.
Given; A hydraulic jack system (see figure) in an equilibrium condition, and data/properties as shown. Determine the Force F applied at the end of the lever arm to maintain equilibrium of the system. Neglect weight of plungers. Hint: Use the law of transmission pf pressure
4. The pressure intensity at a point in a fluid is given 4.9 N/cm². Find the corresponding height of fluid when it 5. An oil of sp. gr. 0.8 is contained in a vessel. At a point the height of oil is 20 m. Find the corresponding m [Ans. (a) 5 m of water, (b) 6.25 m of cil is : (a) water, and (b) an oil of sp. gr. 0.8. (Ans. 16 m) and pbove it an oil of sp. gr. 0.8 for a depth of 2 m height of water at that point.
A 56-mm-diameter siphon is drawing oil (SG = 0.818) from an oil reservoir, as shown in the figure. If the velocity of flow in the pipe is 'v, the head loss from point 1 to point 2 is 2v2/2g, and the head loss from point 2 to point 3 is 5v2/2g. Find the absolute pressure (in kPa) at point 2. Use atmospheric pressure, Patm = 101.38 kPa. Use y1 = 2 m., and y2 = 5 m %3D
In the illustration: A В 2 D All friction factor f - 0.02 All pipe lengths L- 250m Diameter of Pipe A= 400mm with Flow Rate at Pipe A = 700 L/s Diameter of Pipe B = 300mm Diameter of Pipe C = 200mm Diameter of Pipe D = 400mm Solve for - difference in elevation in meters in between reservoirs.
سمنب Fluid mechanics
A vertical triangular gate with Alcohol (SG = 0.78) on one side is shown in the figure. Determine the total resultant force acting on the gate and the location of the center of pressure. +dy 3ft Unit weight of the liquid (y) Value of hbar (h) Area of the rectangular gate (A) Hydrostatic Force (F) Value of (Igx) Value of ybar (9) Location of the Hydro.Force measured from the water surface of the gate inclined (yp) Ib/ f ft ft lb fi ft ft ***answer Hydrostatic Force F on the box below:
Consider the tank shown in (Eigure 1). Take po = 900 kg/m³, Pu=1000 kg/m³, and pHg = 13 550 kg/m³. 0.6 m 0.8 m 100 mm h 1 of 1 > P Part A Determine the level of water in the tube if the depths of ol and water in the tank are 0.6 m and 0.8 m. respectively, and the height of mercury in the tube is h=0.075 m A Express your answer to three significant figures and include the appropriate units. PA h = 240 Submit + Provide Feedback → OF ? mm Previous Answers Request Answen X Incorrect; Try Again; 4 attempts remaining Next > 1231 AM 0
Weter flows up a tapered pipe (figure). A differential mercury manometer is attached to the pipe at Wand B. The pipe has a diameter of 200 mm at A and 100 mm at B, the point B being 1 m above the alot A. Obtain the deflection in the manometer corresponding to a discharge of 50 L/s. Neglect the friction in the pipe. Relative density of mercury 13.6. %D 100 mm 1 m 200 mm
Water flows through a pipe at 152 L/s that changes gradually in diameter from 196 mm at point A to 456 mm at point B. Point B is 6 m higher than point A. The pressures at point A and point B are 126 kPa and 69.3 kPa, respectively. Assume that the datum line passes through point A. Which of the following most nearly gives the head loss in the pipe? (m). Round your answers in 3 decimal places.
diameter = 60 cm height = 60 cm The CLOSE cylindrical tank is two-thirds full of water. It is subjected to pressure = 10 kpag. Considering that the tank is to rotate about the axis at the center at 10 rad/s a. What is the pressure at point C? b. What is the pressure at point D?
Consider the pressurized horizontal pipe network consisting of three pipes arranged in series. The characteristics of each pipe are summarized in the table. The flow of water at Node A is Q = 5 cfs and the pressure head at Node A is yA = 200 feet. The temperature of the water is 60° F. a) Determine the friction head loss hfric in feet in Pipe 1. b) Determine the friction head loss hfric in feet in Pipe 2. c) Determine the friction head loss hfric in feet in Pipe 3. d) Determine the pressure head ys in feet at Node B. e) Determine the pressure head yc in feet at Node C. f) Determine the pressure head yo in feet at Node D. Flow Friction Pressure Diameter Length Friction (feet) (cfs) head Нead Pipe (inches) factor f Kpipe loss (feet) Node (feet) 1 16 500 0.011 5 A 200 2 12 1000 0.013 B 3 10 750 0.015 D Node Node Node Node A в D 5 cfs 5 cfs Pipe 1 Pipe 2 Pipe 3