2. Table 2 shows the list of electrical appliances and its energy consumption use in a normal household. Estimate the maximum operating hours of desktop computer, X if total household electrical bill need to be controlled at RM240 for 28 days, assuming the cost for each kilowatt/hour is RM0.25. Table 2 Electrical Number/ Operating appliance Freezer LED lamp Washing machine Energy consumption (Watt/per hour) 400 50 300 450 1000 550 Unit hours 24/day 8/day 8/week 1 10 1 4/day 8/day X/day TV 1 Air-Cond Desktop computer 1

2. Table 2 shows the list of electrical appliances and its energy consumption use in a normal household. Estimate the maximum operating hours of desktop computer, X if total household electrical bill need to be controlled at RM240 for 28 days, assuming the cost for each kilowatt/hour is RM0.25. Table 2 Electrical Number/ Operating appliance Freezer LED lamp Washing machine Energy consumption (Watt/per hour) 400 50 300 450 1000 550 Unit hours 24/day 8/day 8/week 1 10 1 4/day 8/day X/day TV 1 Air-Cond Desktop computer 1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1.The real efficiency of the best commercial wind turbine is ......... than that of a solar cell. a. more b. equal c. less d. equal or less 2.How can asolar tower power plant supply electricity at night? a. it uses a battery as energy storage b. it pumps water to higher place c. it stores hot oil in thermal storage tanks to produce steam d. it converts electricity into hydrogen fuel
Match The following. Energy derived from organic waste Choose. Energy from interior of earth Choose.
a) How does PV cell produce electricity? b) What are the advantage and disadvantage of PV cell? c) What are the components of PV cell system? d) What causes a reduction in power output from a solar panel?
An electrical component has a reliability of 0.95 over 1,500 hours of normal use (note normal use indicates it follows an exponential distribution). What is the failure rate? What fraction will survive after 300, 500, and 1,000 hours? What is the MTTF?
Please give me ateast 3 topics in Electrical Engineering thesis ideas. give atleast 1 paragraph explanation regarding the topics and its uses in the community. thanks!
3.Question (a) Look up the definition of unit for clothing insulation, called “clo” value. Convert 1.5 clo to a value with an unit in international standard. (b) In the winter, people wear more cloth to keep themselves warm. You have the option of wearing 2 jackets that are 0.3 cm thick or 1 jacket that is 0.6 cm. Assume they are made of the same material and neglect any effect from cloth openings. Which option should you choose to keep you warm? Draw a thermal circuit to help with your discussion.
Assume the initial cost to set up a thermal power plant of 100 MW is 2 million dollars and that of a PV farm of the same capacity is 100 million dollars and the running cost of the thermal power plant is $80 per MWh and that of PV farm is $10 per MWh. Compute the time in years needed for the PV farm to become the most economical if 90% of the plant capacity is utilized in each case.
Determine the following for solar PV power system referred to the data given below. (Assume the efficiency of the solar system =15%) No of PV Modules = 8 Area of each solar cell is =0.3 m2 No of cells in one module = 20 Insolation value =1050 W/m2 Connection scheme = all Modules are connected in Paralel. a. Total output voltage and output power of system. b. Total output current of the system. c. Calculate the output power of the system if any one of the module gets damaged.
Discussion Questions 1- Draw the important components of a steam power station. 2- What factors are taken into account to select the site of steam power station. 3- State the main parts of a thermal power station, and discuss the function of each part. 4- Draw the important components of a Hydro-Electric power station. 5- What factors are taken into account to select the site of Hydro-Electric power station. 6- Draw the important components of a nuclear power station. 7- What factors are taken into account to select the site of nuclear power station. 8- What do you understand from the load curve and what information are converged by a load curve. 9- Discuss the important points to be taken into consideration while selecting the size and number of units generation. 10- Explain the terms, connected load, load factor, plant use factor, diversity factor.
The incremental fuel costs, in dollars per megawatthour, for two units in a plant are given by dF dP, dR dP, Select one: = 0.007P, +7 and During a 24-h period the load on each unit varies between 100 MW and 500 MW, whereas the plant output varies from 200 MW to 700 MW. (a) At what power level should unit 2 begin to take on all the additional load for the most economic operation of the plant? (b) What is the power output of the plant at this point? Neglect losses. a. a: 122.22MW. b: 222.22KW b. a: 222.22MW, b: 122.22KW ca: 122.22MW, b: 222.22MW d. a: 222.22MW, b: 122.22MW = 0.009P₂ +6
The levelised cost of electricity (LCOE) is often used to compare the costs of electricity production from different types of electricity generation plant. Carefully describe the significance of the LCOE and give one advantage and one disadvantage of using this metric to compare plants.
Determine the following for solar PV power system referred to the data given below. (Assume the efficiency of the solar system =15%) No of PV Modules 5 Area of each solar cell is =65 cm? No of cells in one module = 32 Insolation value =1050 W/m2 Connection scheme = all are connected in series. a. Total output voltage and output power of system. b. Total output current of the system. c. Calculate the output power of the system if any one of the module gets damaged.