2. A pump is used to move water (p = 1000 kg/m³) from a lake into a large tank as shown below. The height of the water surface in the tank is 20 meter from the lake surface. The total length of the pipe is L = 100 meter and the pipe diameter is D = 1 meter. The major head loss is estimated as h = LV² where the pipe friction factor f is assumed to be 0.025. Here, V is the flow velocity in the f= D 2g pipe. Determine the flowrate in the pipe. The pump power is W = 2000 Watts

2. A pump is used to move water (p = 1000 kg/m³) from a lake into a large tank as shown below. The height of the water surface in the tank is 20 meter from the lake surface. The total length of the pipe is L = 100 meter and the pipe diameter is D = 1 meter. The major head loss is estimated as h = LV² where the pipe friction factor f is assumed to be 0.025. Here, V is the flow velocity in the f= D 2g pipe. Determine the flowrate in the pipe. The pump power is W = 2000 Watts

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2/ A fluid containing (water, oil, sand) flowing through the tube and open to the atmosphere as shown in the figure below.. Note that p°- 1.013*105 Pa Calculate the absolute pressure (Pa). Density: Pwater = 1000 kg/m Pail = 800 kg/m Pand = 200 kg/m P. h3=12 cm hg al2cm oIL Pa h25 cm ng = 6 cm %3D Sand water
A pipe of 400 mm diameter carries water at a velocity of 25m/s. The pressure at the points A and B are given as 29.43 N/cm? and 22.563 N/cm? respectively while the datum head at A and B are Find the loss of head between A and B. 18 m and 19 m De = 400 mm Pe = 22.563 N/cm PA 29.43 N/cm =28 m DA =400 mm ZA DATUM LINE
Q2/ A pump delivers water from a tank A (water surface elevation = 110 m) to tank B (water surface elevation = 170 m) as shown in figure below. The suction pipe is 45 m long ( = 0.024) and 35 cm in diameter. The delivery pipe is 950 m long (f = 0.022) and 25 cm in diameter. The head discharge relationship for the pump is given by H, = (90 – 8000 Q*), where H, in m and Q in m³/s. Calculate the discharge in the pipeline and the power delivered by the pump. Delivery pipe. elevation 170 m Suction pipe, elevation- 110 m Good Luck Rasha H. Salman
Tank 1 Tank 2 g Question 1 Consider the flow of water (p= 10³ kg/m³, u = 10³ Pa-s) from tank 1 to tank 2. A centrifugal pump is installed in this piping system with length L = 300 m and diameter D = 40 cm cast-iron pipe. The water surface of tank 1 is 15 m higher than the water surface of tank 2. You may neglect minor losses but not major losses. The gravity cannot be neglected. Assume steady-state and no friction in the tanks. (a) Simplify the equation of the system curve Ap vs Q. Do not place numerical data. (b) Plot the system curve Ap vs Q (0 ≤Q≤2 m³/s). (c) Find the volumetric flow rate when the pump is not operating. (d) Find the power supplied to the water and to the pump if n = 0.9 and 1 m³/s. (e) Consider a pump: Ap = 106 105 Q², where Ap in Pa and Q in m³/s. Find the operating point. What is the minimum and maximum volumetric flow rate that this pump can deliver?
At the gasoline transfer facility (ρᵣₑₗ=0,75) from the pond of storage to consumption, you want to install a pump to circulate a flow of 40(lt/s). The 400m long pipe is cast iron 150mm in diameter and consists of a check valve, a gate valve and 2 commercial medium radius elbows. The consumption tank is pressurized to 2,9 (kgf/cm²) gauge pressure. Decide the drive power of the pump in KW if its performance is 70%. •Additional data, pressure drop factors: •Retention valve Kᵣ = 1,5 •Gate valve open Kᵥ = 0,21 •Medium Radius Commercial Elbow Kc = 0,75 for each cubit •Storage pond outlet sharp angles Kₛ = 0,5 •Entrance to consumption pond Kₑ = 1 •Friction factor in pipes f = 0.026
A pump works between two opened tanks through a piFe of 10 cm diameter and length of 30 m with a friction factor of 0.02. The characteristic formula of the pump is given by H-52-1010 Q. There is a valve friction factor of 0.02. The characteristic formula of the located before the pump of minor losses factor (K) S Eten by the figure Q2 below, If the height of deliver side tank is 3 m Find:1) The volumetric fiow late n vaje Is fully opened 2) The percent valve setting if the dow rate is reduced by a half of the rate in )ASsame, free and large tank at the suction side tank]. Pump is given by H-52-1010 Q. There is a valve
This is a fluid machine question. Water reservoir is pumped over a hill through a pipe 450 mm in diameter and a pressure of 98.08 kPa is maintained in the summit water discharge is 30 m above the reservoir. The quantity pumped is 0.50 m3/s. rrictional losses in the discharge and suction pipe of the pump is equivalent to 1.5 m head loss. The speed of the pump is 800 rpm, what amount of energy must be furnished by the pump in kW?
A pump receives water from a tank. If the pump needs 24 m of NPSHA, how high must the water level be above the pump centerline if the water is saturated at 1724 kPag? The friction loss in the pipe averages 0.3 m for each 6 m of height and flow is 23 lps in a 15.24 cm ID pipe.
The distribution system requires to lift water to an area with an average elevation of 90 mamsl from the pumping station at 35 mamsl. The area has a demand requirement of 30 MLD and the minimum pressure head requirement is 20 m-head. The pipe which will serve the area is 500 mm with C-value of 90 and length of 3000 m. Determine the following: a) total head loss along the pipe in meter, b) the head of pump required in meter, and c) the power required by the pump with an efficiency of 80% in kilowatt. Note: Theaverage water surface level of the reservoir which supports the pumping station is 5 m.
A vertical pipe of 1 m diameter and 14 m length has a pressure head of 5 m of oil at the upper end. When oil flows through the pipe at an average velocity of 4.5 m/s, the head loss due to friction is 1.8 m of oil. The density of oil is 840 kg/m3 Find the pressure at the lower end of the pipe, when the oil flow is (a) ) Pressure at lower end when flow of oil upward direction (b) ) Pressure at lower end when flow of oil downward and also draw the neat sketch.
A centrifugal pump is used to pump water through horizontal distance of 150 meters and then raised to an overhead tank 20 meters above. The pipe is smooth with inside diameter of 50 millimeter. The pump head (meter of water) that will be generated at its exit to deliver water at a flow rate of 0.001 cubic meter per second is Blank 1 meter of water. Use fanning friction factor = 0.0062 Express your answers in whole siginificant figure without decimal value and without unit
A water pump is used to pump the water to a large water tank as shown in Figure. The free surfaces of both water tanks are under atmospheric pressure. Dimensions and local losses are given below. The flow rate of the pump is determined as 16.2 L/min. Calculate the required manometric head of the pump and the required motor power if the total efficiency is 76.2 percent. The water at 10oC. density r = 996.2 kg/m3, dynamic viscosity µ = 1.362x10-3kg /ms. z2-z1 = 7.62 m (height difference), D = 2.62 cm (pipe diameter), L = 176.2 m (total pipe length), ɛ = 0.2562 mm (pipe roughness value) Local loss coefficients: KL,inlet = 0.562 (pipe inlet) KL,valve = 16.2 (valve), KL,elbow = 0.9262 (there are 5 elbows totally in pipe line), KL,outlet = 1.0562 (pipe outlet).