And explain how too, please thank you! 2. A bronte bar is fastened between a steel bar and an aluminum bar as shown in Figure.Aaial foads are applied at the positions indicated. Find the targest value af P that will notexceed an overall deformation of 3.0 mm, or the fallowing stresses: 140 MPa in thesteri, 120 MPa in the bronze, and fi0 MPa in the aluminum. Asume that the amemblyin suitably braced to prevent buckling. Use E = Z10 GPa, Eui = 70 GPa, and fi =这GPa.SteelA = 480 mmBronzeA = 650 mmAluminumA = 320 mm3P4P2P1.0 m2.0 m1.5 m

Answered: Image /qna-images/answer/10e734db-7c11-4183-94d5-392e7cf040d2.jpg

2. A bronte bar is fastened between a steel bar and an aluminum bar as shown in Figure. Aaial foads are applied at the positions indicated. Find the largest value of P that will not Exceed an overall deformation of 3,0 man, or the failowing stresses: 140 MPa in the steri, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly in suitably brated to prevent buckling. Use En Z10 GPa, Eu 70 GPa, and fi 3 GPa. Steel A = 480 mm Bronze A= 650 mm Aluminum A = 320 mm 3P 4P 2P 1.0 m 2.0 m 1.5 m

2. A bronte bar is fastened between a steel bar and an aluminum bar as shown in Figure. Aaial foads are applied at the positions indicated. Find the largest value of P that will not Exceed an overall deformation of 3,0 man, or the failowing stresses: 140 MPa in the steri, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly in suitably brated to prevent buckling. Use En Z10 GPa, Eu 70 GPa, and fi 3 GPa. Steel A = 480 mm Bronze A= 650 mm Aluminum A = 320 mm 3P 4P 2P 1.0 m 2.0 m 1.5 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Ranking metal shaping processes by kg carbon footprint (per kg of stuff produced) which of the following is the correct ranking (least carbon footprint to most)? Extrusion, Forging, Wire drawing, Casting, Vapour Deposition Methods, Powder Forming Forging, Casting, Extrusion, Powder Forming, Wire drawing, Vapour Deposition Methods Casting, Forging, Extrusion, Wire drawing, Powder Forming, Vapour Deposition Methods Casting, Extrusion, Forging, Wire Drawing, Powder Forming, Vapour Deposition Methods
Q3 Give the reason for 10 of the following. - 1- The use of lubricant in wire drawing die. 2- The uses of tungsten carbide for the manufacturing of die tool. 3- The increase of Mo/Si ratio during the production of white cast iron. 4- The addition of Al to copper alloys. 5- Aluminum is a better overall conductor than Copper for long distance electric transformation. 6- The addition of cryolite in smelting electrical furnace due to the production of aluminum. 7- The addition of Magnesium and Cerium during the production of Ductile cast iron. 8- The addition of 13% Cr to steel in corrosive environment. 9- The increase of hardness for chips due to the cutting process. 10- The brittle fracture of steel at low temperature lower than -4 C. 11- The heating of metal after the rolling process.
nQ2. Write short notes on Surface treatment process. List any two examples for Joining and assembly process.
Name some products that can be manufactured by shape rolling and thread rolling
If you were manufacturing a precision component which has a mass of around 15 grams and which was a solid 3D shape, which method would be appropriate?
Give the definition of the following drawing materials and state their functions.
Q.2- Answer two of the following: a) State the types of sheet metal bending process and compare (in table) between them. b) What the Difference between brazing and soldering? (Compare in table). c) Compare (in table) between shaping and planing operations.
15 What are the four stages in the stress-strain curve of low-carbon steel? please quickly thanks !
Name the following terms
Suggest three alternative materials that could be used to produce the desired wrench? Construct a comparison table to explain the advantages and disadvantages of each one? Cite appropriate references. Which of your alternative would you recommend to your supervisor?
Kindly answer by giving proper explanation .. remember this for upvote
a) Briefly explain what is meant by the following: i. Cold-working, ii. Hot-working b) Briefly explain the following as applied to heat treatment of plain carbon steels: i. Hardening ii. Annealing iii. Tempering iv. Normalizing c) Estimate the recovery temperature for a cold worked sheet metal if its melting temperature is taken as 1080 degrees Celsius