B) State whether the sentence is true or false (answer 5 only). 1. The preconsolidation stress seprates between the overconsolidated state and normal consolidated state. 2. The soil may consolidate when the ground water table level rise up. 3. In flownet, the head loss in each drop is constant. 4. In flow net, the equipotential lines represent lines of equal potential. 5. The shear strength of granular material is affected largely by the initial void ratio. 6. Drained triaxial compression test means that the soil specimen is dry.

B) State whether the sentence is true or false (answer 5 only). 1. The preconsolidation stress seprates between the overconsolidated state and normal consolidated state. 2. The soil may consolidate when the ground water table level rise up. 3. In flownet, the head loss in each drop is constant. 4. In flow net, the equipotential lines represent lines of equal potential. 5. The shear strength of granular material is affected largely by the initial void ratio. 6. Drained triaxial compression test means that the soil specimen is dry.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular beam is subjected to a pure bending moment M. The cross-section of the beam is shown in Fig. 1.34. Using the elementary flexure formula, determine the normal and shearing stresses at a point (x, y) on the plane AB shown.
A thin cylinder have inner radius 175 mm and thickness 4 mm subjected to an internal pressure of 3MPa. Determine average circumferential stress
A spherical pressure vessel has an inner radius of 1.5 m and a wall thickness of 12 mm. Draw Mohr’s circle for the state of stress at a point on the vessel and explain the significance of the result. The vessel is subjected to an internal pressure of 0.56 MPa
2. Nitrogen gas at 15 °C has a density of 0.07616 Ibm/ft³ with a kinematic viscosity of .146 cm²/s forms a boundary layer near a solid wall. The velocity distribution in that boundary layer is given by the expression u = 1-e where U = 15 m/s and 8 = 1.2 cm. Find the shear stress at the wall (y=0.005 m).
Read the question carefully and give me the right solution according to the question
Blk gkl
N B 0 Horizontal The stresses shown in the figure are applied at a point in a dry clayey sand soil mass. A= 50 kPa and B= 125 kPa The shear strength parameters of the clayey sand are: c'= 9kPa and p'=29° 0=30° a) The value of the shear stress, T, is slowly increased. What value would cause shear failure at this point (in kPa)? b) At failure, what angle does the failure plane make with the horizontal (in degrees)?
(c). The magnitude of stresses have been applied on soil element where Normal vertical stress is 120 KN/m2 , Normal horizontal stress is 300 KN/ m², shear stress is 40 KN/m² and Angle of internal friction is 20°. Find the Principle stress and Normal and Shear stress on plan AB, figure 1. Oy В it Ox Ox A Oy Fig .1 Solution: 1. 01.. . 2. 03.. . 3. On.. .4. Tn..
4.1 A line load of q = 60kN/m with a = 0 is placed on a ground surface as shown in Figure P4.1. Calculate the increase of pore water pressure at M immediately after application of the load for the cases given below. (a) z = 10m, x = 0m, v=0.5, A=0.45. (b) == 10m, x= 2m, v= 0.45, A=0.6. 2 m 4. G.W.T. Clay XI 1
R2
Problem Ex. Consider the upward flow of water through a layer of sand in a tank as shown in Figure. 1.5 m 0.7 m I m 2 m Valve (open) Inflow O Sand For the sand, the following are given: void ratio (e) = 0.52 and specific gravity of solids (G.) = 2.67. Calculate the total stress, pore water pressure, and effective stress at points A and B. What is the upward seepage force per unit volume of soil? Total stress, porewater pressure, effective stress. Point A t B Total stress (kN/m?) Porewater pressure Effective stress Upward seepage force.
). A circular bar of 2 m length has a diameter 100 mm (E=200 Gpa, v=0.32, a = 11.7µ/c°). The bar's left end is built into a rigid wall and a gap of 0.5 mm exists between right wall and right end of the bar prior to an increase in th temperature. The temperature of the bar is increased uniformly by 80 c°. Determine the average axial stress and change in the diameter of the bar 15