e post shown, whose cross-sectional area is 100 x 150 mm2, rests at the middle of a circular solid steel plate. The steel plate is placed above a hollow cylinder. Both the steel plate and the cylinder have diameter of 300 mm and a thickness of 20 mm. Solve for the following: a. punching shear stress in the steel plate b. punching shear stress in the hollow cylinder c. bearing stress in the steel plate due to the post d. bearing stress in the cylinder due to the steel plat

Q: Question A 12 mm thick plate is connected to two 8 mm thick plates, on either side through a 16 mm…

A: Given : thickness of plate= 12mm  connect to 8mm thick plate  2×8>12  hence  t= 12mm Dia of rivet…

Q: Which stress element below correctly shows the normal and stress at point X? M T A G B D H Write the…

A:

Q: Three rods of different materials are connected and placed between rigid supports at A and D, as…

A:

Q: n aluminium channel section is shown in the figure below: 4mm I; mm mm l mm s indicated, the…

A:

Q: The state of stress at a point Q is Ox = 100 MPa, o, = 20 MPa, oz = -40 MPa, Txy = 0 MPa, Tyz = 40…

A:

Q: An aluminium channel section is shown in the figure below: i mm 1; mm mm I mm As indicated, the…

A: Given L1=167mm t1 =1mm  L2 =218mm t2=3mm

Q: A bronze bar 3 m long with a cross-sectional area of 320 mm² is placed between two rigid walls as…

A: length of bronze bar = 3 m Area of bar =320 mm2 Temperature =-20 0 C  Gap, ∆=2.5 mm E = 80GPa α = 18…

Q: A rectangular steel block is 4 inches long in the x direction, 3 inches long in the y direction, and…

A:

Q: Q1) Three bars AB, CD and ED are used to support ACE beam. The three bares have modulus of…

A: Draw the free body diagram. Equilibrium of vertical forces,…

Q: The belt shown has a width of 43 mm and a thickness of 6 mm. [P1= 30 kN, P2= 6 kN, P3= 14 kN, P4= 14…

A: the width of the belt (b)=43 mm,  thickness (t)=6 mm.P1=30 kN, P2=6 kN, P3=14 kN, P4=14 kN.…

Q: Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an internal…

A:

Q: The bronze bar 3 m long with a cross-sectional area of 450 mm² is placed between two rigid walls. At…

A: Given: L = 3m, A = 450mm2 Find: Temperature at which the compressive stress equals = 33MPa

Q: d has a diameter of 40 mm. (Figure 1) It is ed to the force system Fx = 1560 N, 505 N, F=830 N. Part…

A:

Q: Problem # 3: The steel bars are firmly attached to rigid supports. Initially the temperature is…

A:

Q: Write the equation for finding the principal stresses

A: Given data in question  Principal stress  To find out  Equation for Principal

Q: For the assembly shown in the figure below, Determine the state of stress at point A on the cross…

A: Given: P = 230KN, d = 24mm, a = 160mm, b = 260mm

Q: FIGURE 1 are applied at of steel, bronze rigidly attached together. If P = 3000 lb and the…

A:

Q: Calculate the increase in stress in steel segment of the compound bar if the temperature is…

A:

Q: Question 5 A steel column with a rectangular hollow section is subject to a vertical downward load…

A: P1 = 500KN P2 = 100KN e = 110mm

Q: THE PLATE SHOWN IN THE FIGURE IS FASTENED TO THE FIXED ΜΕMBER BY FIVE 10- MM- DIAΜΕ TER RIVETS.…

A:

Q: Q.1. A. For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138,…

A:

Q: Q. A For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138,…

A: Note:- as per our company guidelines we are supposed to answer only first part. Kindly repost other…

Q: 200KN A steel rod is rigidly attached between an aluminum and bronze rod. The diameters of each…

A: Stress = force / area  DAl = 20 mm  Ds = 28 mm DBr = 25 mm

Q: For the assembly shown in the figure below, Determine the state of stress at point A on the cross…

A: Given: P = 210N, a = 230 mm , b = 130mm, d = 26 mm

Q: SIMPLE STRESSES 340 mm 1. Two plates are connected by bolts as shown in the figure. Compute the…

A: To determine the bearing stress in each bolt.   Given, Diameter of each bolt (d) = 20 mm Magnitude…

Q: At an axial load of 26 kN, a 35-mm-wide by 15-mm-thick polyimide polymer bar elongates 2.9 mm while…

A: Answer  (a) We know that Modulus of Elasticity is given by E = σε σ = stress σ = loadArea…

Q: Question 4. Three wires are used to suspend the plate shown. Aluminium wires used at A and B with a…

A:

Q: A three part bar is connected to walls at D and C and loaded as shown. Middle section AB is solid…

A:

Q: Find the Stress if Tensile force 2.3 N applied on rod having cross sectional area of 1 mm2

A: Introduction : The question is related with solid mechanics . In this question the data of tensile…

Q: An aluminum [E = 11100 ksi] control rod with a circular cross section must not stretch more than…

A: Given data,  Stress = 10.8 ksi E = 11100 ksi P = 2090 lb

Q: Question: A 12 mm thick plate is connected to two 8 mm thick plates, on either side through a 16 mm…

A: Given- Thickness of plate T=12 mm, Dia of rivet=16 mm, Permissible bearing stress p=270 MPa, It is…

Q: A solid brass shaft is loaded as shown below by two torques TB= 1100 Nm and TC= 400 Nm. The lengths…

A:

Q: Shown below is a steel tube AB with a 1.5" outside diameter and .06" wall thickness. You may assume…

A:

Q: 3. A square foundation is constructed in a soil deposit as shown in the figure below. Assume that…

A: Formula to calculate the ultimate bearing capacity of footing is given by qu = C'Nc Fcs Fcd Fci + q…

Q: The cross section of the AB part of the welded pipe part given in the figure is a hollow pipe and…

A: Given: The inner diameter of the pipe AB is 20 mm. The outer diameter of the pipe AB is 28 mm. The…

Connections

In steel structures, connections are the members that join two or more steel members. The connections are the most important members of any steel structure, and hence, they are designed more carefully. The majority of the construction cost of steel structures is incurred due to the connections. The design of connections is done as per the recommendations and specifications of the American Institute of Steel Construction (AISC).