16. Consider a simple positive phase sequence, three-phase, three-wire system operated at 50 Hz and with a balanced load. Each phase voltage of 240 V is connected across a load composed of a series-connected 50 2 and 500 mH combination. Calculate (a) each line current; (b) the power factor of the load: (c) the total power supplied by the three-phase source.

16. Consider a simple positive phase sequence, three-phase, three-wire system operated at 50 Hz and with a balanced load. Each phase voltage of 240 V is connected across a load composed of a series-connected 50 2 and 500 mH combination. Calculate (a) each line current; (b) the power factor of the load: (c) the total power supplied by the three-phase source.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.22P: A balanced Y-connected voltage source with Eag=2770volts is applied to a balanced-Y load in parallel...

See similar textbooks

Similar questions

Consider the system shown in Figure 1. Assume the load voltage (VL) is 4720 V and the load consumption is 80 kVA at 0.85 lagging power factor. The line impedance (Zline) is 4.6+j8.5 2. The parameters of the 14,400/4800-V single-phase transformer referred to the secondary are: Req=0.95 , Xeq = 1.74 , Re = 48.5 kn, and Xm = 31.1 k. vp avs 4.6 +19.52 Zline Vs ~ P a:1 ele rmis alf Reais leee V₂ zí S Figure 1: System for Q1 I wad a) Find the current of the load. b) Find the primary and secondary voltages of the ideal transformer. nuomo I un cucc + Bline Xeq,s 1 V₂² 95, 74-32 1. VL 4720 Ponerlosture -> Pont IL = V₂ -V₂ Zine
Problem 1 - Series en Parallel AC networks [19] Look at the circuit in Figure 1 and determine the following: (a) Total Admittance. (b) Total Impedance. (c) Total Current (l:). (d) Current (I1) through impedance Z2. (e) Current (12) through impedance Z3. (f) Current (I3) through impedance Z4. (g) Is this an inductive or capacitive circuit? A. B Zs 220V;50HZ Figure 1 (h) Voltage across Z1. (i) Voltage across A and B. G) Voltage across Zs. Z1 = 3 + j5 ohm Z2 = 10 + jo ohm Z3 = 5 + j15 ohm Z4 = 10 – j30 ohm Zs = 20 – j30 ohm Admittance and Impedance in rectangular notation. All currents and voltage in polar notation. Take voltage as reference.
Q4/For the three-phase power network shown in Figure. the various components are: GI: 100 MVA, 0.30 pu reactance. G2: 60 MVA, 0.18 pu reactance. Transformers (cach): 50 MVA, 0.10 pu reactance. Inductive reactor X: 0.20 pu on a base of 100 MVA. Lines (each): 80 ohms (reactive); neglect resistance. with the network initially unloaded and a line voltage of 110 kV, a symmetrical short circuit occurs at midpoint E of line 2. Calculate the short circuit MVA to be interrupted by the circuit breakers A and B at the ends of the line. T3 38 L1 L2 G2 Bas 12 T4 Bus
Please help with this balanced three-phase circuit problem.
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator2. “Reactive power in a system is dissipated generally as thermal energy?”A. TRUEB. FALSE3. Which of the following statements are correct for three phase circuit:A. Sum of all the three phase currents is zero in unbalanced networkB. Total power transfer to load is constant with timeC. Neutral conductor is same size in terms of material used as in single phase conductorsD. Net apparent power consumed is equal to real power
Connect three single-phase transformers in Y-Y, with subtractive polarity, so that the line-to-line voltages on the primary are 30 degrees delayed to their respective line-to-line voltages on the secondary. It should show each step that is needed to make this connection (example: the phasor diagram) and should show the final connection of the three transformers including the polarity markings. Assume phase A on the primary is terminal "H1".
Two 7970-V:230-V single-phase transformers with impedance with respect to their secondaries of 1.5 + j3 and 2 + j4.5 ohms are connected in parallel to a 7900-V source. Their secondaries are supplying a common load of 30 + j40 ohms. A. What is the magnitude of the voltage across the load in volts? (2 decimal places) B. What is the magnitude of the total current supplied by the 7900-V source in amperes? (3 decimal places) C. What is the efficiency of the parallel transformers combined in percent? ( 1 decimal place)
Two 7970-V:230-V single-phase transformers with impedance with respect to their secondaries of 1.5 + j3 and 2 + j4.5 ohms are connected in parallel to a 7900-V source. Their secondaries are supplying a common load of 30 + j40 ohms. What is the magnitude of the voltage across the load in volts? (2 decimal places)
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator
Transkrmers phase with each bank with - adjuste 35. Three single-phase transformers, cach of 100 kVA rating, are conected in a closed-delta arrangement. If one of them is taken out, it would be possible to load the bank in such a manner that cach one is loaded to the extent of: A 86.6 kVA C. 57.7KVA B. 66.7 kVA D. 33.33 kVA when load is at unity power factor. 36. Average power factor at which V-V bank separate is A 86.6% C. 66.67% В. 73.3% D. None of these 37. Scott connections are used for: A. single-phase to three-phase transformation C. three-phase to two-phase transformation B. three-phase to single-phase transformation (D Any of the above 38. The current in low voltage winding of a 25 kVA, 6600/400 V, 50 Hz, 3-phase Y-A transformer, at full load is: A 36 A Č. 65,32 A B. 20.78 A D. 40.2 A 39. The current in high voltage winding of a 20 kVA, 2200/220 V, 50 Hz, 3-phase A-A transformer, at full load is: (A. 3.03 A C. jo.5 A B. 5.25 A D. None of above 40. The current in low voltage…
Three single-phase transformers (ideal) are connected as shown in the figure below to supply a balanced 3-phase, 150 KVA, 600 VL load from primary 4.16 KVLL line. H1 X1 H2 X2 BALLANCED H1 X1 THREE PHAGE LOAD H2 X2 H1 X1 X2 (a) Draw (neatly) a phasor diagram showing the three, primary line-to-line voltages and the six secondary phase and line voltages. What is the phase relationship between the primary voltage VAB and the secondary voltage V12? Indicate on the phasor diagram:f
2) The one-line diagram of a three-phase power system is as shown in Figure. Impedance are marked in per-unit on a 100-MVA, 400-kV base. The load at bus 2 is S2=15.93 MW - j33.4 Mvar, and at bus 3 is S3-77 MW + j14 Mvar. It is required to hold the voltage at bus 3 at ...L0 kV. Working in per-unit, determine the voltage at buses 2 and 1. (Please determine the voltage magnitude within the specified limits: 410-450 V. By considering the voltage magnitude value you determined yourself, solve the question.) V₁ j0.5 pu V₂ j0.4 pu S₂ Figure V3 S3