14. The cost of borrow per cubic meter is P500 and the cost of haul per meter station is P20. The free hauldistance is 50m long. Compute the length of economic haul.a. 450 mc.350 mb. 300 md. 500 m15. The length of economic haul intersecting horizontally the summit mass diagram is 450 m. The freehaul distance is 50m. The vertical distance between the free haul distance and limit of economichaul is 3 cm. If the scale of the diagram is 1 cm = 100 m³, determine the volume of overhaul in m³.a. 350c. 300d. 250b. 400

"Since you have asked multiple question, we will solve the first question for you. If you want any…

14. The cost of borrow per cubic meter is P500 and the cost of haul per meter station is P20. The free haul distance is 50m long. Compute the length of economic haul. a. 450 m c. 350 m b. 300 m d. 500 m

14. The cost of borrow per cubic meter is P500 and the cost of haul per meter station is P20. The free haul distance is 50m long. Compute the length of economic haul. a. 450 m c. 350 m b. 300 m d. 500 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A railway curve of 1350 m radius is to be setout ta connect two tangents. If the design speedis 110…

A: Radius of curve = 1350 mDesign speed = 110 kmphRate of change of acceleration = 0.3 m/s3To Find…

Q: Can you explain the eqautions and processor for finding the location of the trust on the wall? I am…

Q: Question 2: Determine the required reinforcement for L section beam to resist torsion T = 10KN.m…

A: Torsion = 10 kN.mDepth of slab = 100 mmWidth of flange = 900 mmWidth of web = 200 mmDepth of web =…

Q: Q3: For the Column in Shown in Figure, Design the Base Plate with A36 steel, if the service dead…

Q: The beam is supported by a pin at point A and frictionless pulley system at D. The cylinder with a…

Q: Determine how much a builder will pay a lumber wholesaler for 1200 pieces of 2" x 12", 1000 pieces…

A: “Since you have posted multiple questions, we will provide the solution only to the first question…

Q: A crest and sag curve connect a 0% road segment with a +2% road segment. The two curves connect with…

Q: 6-3. Draw the influence lines for (a) the vertical reaction at B, (b) the moment at C, and (c) the…

Q: A rectangular swimming pool has a length of 35 meters, a width of 10 meters, and is filled with…

Q: (a) What is the pore water pressure at point A (kPa), and what is the effective stress at point A…

A: Given:Required:Pore water pressure and effective stress at Astate below statement is true or…

Q: Sec. 6.1-6.3 6-1. Draw the influence lines for (a) the moment at C, (b) the vertical reaction at A,…

Q: Steel tape used in a tape measure has a thickness of 0.0065 in. If the allowable stress is 68 ksi,…

Q: A 20m Fink Truss are spaced at 'S' meters o.c. the purlins are made up of C10X20 sections and are…

A: Fy = 248 MPaC10X20 properties: w = 29.76kg/mA = 3787.09 mm2 Ix = 32.84x106 mm4Iy = 1.17x106 mm4Zx =…

Q: Set P₁14 kN and P₂ = 9 kN. (Figure 1) Figure F z B 2 m A 1 m 2m 1 of 1 1m D

A: Given data - P1 = 14 KNP2 = 9 KN Find out - Force in the members of the truss.

Q: Situation 1 - For the continuous beam shown in the figure, determine the following: 12 kN/m P = 50…

A: To derive the moment equation for points A and B, we can use the Three-moment theorem,6MA + 2MB + MC…

Q: served lengths of the sides (in feet) of a five-sided closed polygon traverse follows: 202.74,…

Q: A pipe has an outer diameter of 26 mm and an inner diameter of 19 mm. What is the polar moment of…

Q: A simply supported beam has a span of 20 ft. If the cross-section of the beam is as shown in Figure,…

Q: Situation A cantilever beam, 3-5 m long, carries a concentrated lo Given: P = 200 kN Beam Modulus of…

Q: Current Attempt in Progress A composite beam is fabricated by bolting two 2.4-in.-wide by…

Q: Problem 1 The boom is intended to support two ve cable CB can sustain a maximum loa determine the…

Q: The velocity distribution for a flow over a plate is given by u = 3y^2 + 2y where u is velocity in…

A: Velocity distribution U = 3y2 + 2ydynamic viscosity = 9 poise To Find :The shear stress at a…

Q: What is the total angle of twist in radians for the following metal shaft? Answer to 4 decimal…

A: Torque=T=1.544lb-inlength=L=1ftridigity=G=9290ksipolar moment of inertia=J=

Q: Determine the shear and moment throughout the beam as a function of x. 15 kN/m 4m 2 m

A: The simply supported beam is shown in the above figure. We have to determine the shear and moment…

Q: The Orifice Origin: Textbook Compute the velocity of the water through an orifice that is draining a…

A: Height of tank = 10 m

Q: Determine the force in members EF and state if the member is in tension or compression. Give your…

A: Given Loads 5, 10, 10 & 5 kNSpan 4 mTo find out Member force in EFNoteWe will use method of…

Q: A beam is subjected to equal bending moments of M₂ = 30 kip-ft. The cross-sectional dimensions are…

A: A beam is subjected to equal bending moment, M = 30 k-ft, we need to find out the bending stress at…

Q: A tank contains water for a depth 2m and filled with oil of specific gravity 0.8 for 3m depth above…

Q: The depth of water in a cylindrical tank of diameter D is a function of the diameter of the orifice…

A: Dimensional analysis involves identifying the base dimensions involved and forming dimensionless…

Q: Water with sp.gr 0.97 flows through a pipe of uniform diameter 350mm with a mean velocity of 1.0…

A: SG = 0.97 D = 350 mm or 0.35 m V = 1 m/sP1 or 250,000 Pa

Q: beam ABCD with a vertical arm CE is supported as a simple beam at A and D (see figure). A cable…

Q: 1. Determine the degree of indeterminacy. A. 0 B. 1 2. Determine the degree of indeterminacy. A. 0…

A: Determine the degree of indeterminacy (DSI) of each beam.

Q: A cantilever timber beam with a span of L = 3.6 m supports a uniformly distributed load w. The beam…

A: Maximum bending stress = 6.8 MPa Determine the magnitude of the maximum load w that may be carried…

Q: Determine the reactions at the supports for the structures shown

A: Given Load 400 kN/mInternal moment 6000 kNmSpan 35 mTo find out Reactions

Q: Use the scraper specifications in Table 8.1 of the textbook and the performance charts in Figures…

A: Given:-A wheel-tractor scraper is operating on a level gradeThere is no power derating required for…

Q: Problem 6: Energy Equation Demonstration Recently we saw a laboratory apparatus demonstrate several…

A: At point A and E,applying the continuity equation,given pressure at Cavitation: When the static…

Q: 1.90m diameter closed cylinder, 2.75m high is completely filled with oil having sp.gr. of 0.8 under…

Q: A sample of soil has a weight of 41.8lb, volume of 0.39ft^3, and a water content of 11.3%. What is…

Q: reinforced beam will be provided with the reinforcing bars corresponding to 90% of the maximum…

A: (a) Estimation of steel areaThe steel area can be estimated using the following formula:Ast =…

Q: Draw the shear and bending-moment diagrams for the beam and loading shown. Also determine the…

A: An overhanging beam with uniformly distributed load and a point load.Beam sectionTo find:…

Q: What is the total length in feet of a road project that starts at station 10+00 and ends at station…

A: starting station =10+00end station= 125+35.23find the length of road in feet

Q: F7-12. Determine the average normal stress in rod AB if th load has a mass of 50 kg. The diameter of…

A: The load has a mass = 50 kgThe diameter of rod AB = 8 mmTo find:The average normal stress

Q: Determine the force in members EF and state if the member is in tension or compression. Give your…

Q: 2 kN/m 10 KN Z 4 kN/m 20 KN Z 20 m Figure P1.3 15 m 15 m

A: A frame is given we need to find out the reactions at supports.

Q: 3. Determine the Determine the reactions at A and B. 6 ft 4 kip/ft |C 6 ft B

Q: Water (60°F) is running through Schedule-80 PVC pipe whose size changes gradually from 6-in nominal…

A: To solve this problem, we can use the Bernoulli equation, P + 1/2 * ρ * v² + ρ * g * z =…

Q: In a suburban area of a city, the total time dedicated to waste collection is, on average, 100 times…

A: To calculate the truck's average load volume for each collection,convert the compaction ratio from a…

Q: The wide-flange beam is subjected to (Figure 1) Figure 200 m

Q: AD P

Q: How do you get 45 degrees and 26.565 degrees

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

14. The cost of borrow per cubic meter is P500 and the cost of haul per meter station is P20. The free haul
distance is 50m long. Compute the length of economic haul.
a. 450 m
c.
350 m
b. 300 m
d. 500 m
15. The length of economic haul intersecting horizontally the summit mass diagram is 450 m. The free
haul distance is 50m. The vertical distance between the free haul distance and limit of economic
haul is 3 cm. If the scale of the diagram is 1 cm = 100 m³, determine the volume of overhaul in m³.
a. 350
c. 300
d. 250
b. 400

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Mentioned the given data from the question.

VIEW

Step 2: Calculation of the length of Economic haul .

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A shift with surface area =0.0549 m2 is being pushed at a speed of 400 mm/s through The clearance (0.1 mm) is filled with oil µ- 5 N.s/ m2.Find the force exerted by the ?oil on the shaft 1098 N O 1098 N/m2 O 10.98 N O
A barge 10m wide by 30 m long when loaded the barge displaces 5 MN and its center of gravity is 0.5 m above the water line. a. Compute the righting moment for a roll angle of 10° Unit of the Correct Answer: kN-m Decimal Places required in the final answer: 4 b. Find the value of MBo. Unit of the Correct Answer: meter Decimal Places required in the final answer: 4 c. Determine the metacenter height above the center of gravity for a roll angle of 10°. Unit of the Correct Answer: meter Decimal Places required in the final answer: 3
2. Four machines are equally spaced along the length of an 8 m fixed- free beam of elastic modulus 210 x10° N/m² and cross-section moment of inertia 1.6x10 mt, as shown in Figure 2. Determine the flexibility matrix for a four degree-of-freedom model of the system with the location of the machines as the generalized coordinates. 2 m - 2m 2 m- E-210x 10° Nim 1-1.6x 10 kg-m Figure 2. Four machines along the span of a fixed-free beam.
The 59-kg crate is stationary when the force Pis applied. Determine the resulting acceleration of the crate if (a) P-0, (b) P - 74 N, and (c) P = 247 N. The acceleration is positive if up the slope, negative if down the slope. S4, = 0.16 Hk =0.13 59 kg
The tractor-trailer unit is moving down the incline with a speed of 6.0 mi/hr when the driver brakes the tractor to a stop in a distance of 4.3 ft. Estimate the percent increasenin the hitch-force component which is parallel to the incline, compared with the force present at steady speed. The cart and its load combined weigh 600 Ib. State any assumptions. 15 Answer: n =
2.Determine the value of W if the 100kg crate is on the verge of tipping forward as it slides up the incline. Use d = Im. 0.6 m 1.8m fk = 0.2
3/1 The 50-kg crate is projected along the floor with an initial speed of 7 m/s at x = 0. The coefficient of ki- netic friction is 0.40. Calculate the time required for the crate to come to rest and the corresponding dis- tance x traveled. Vo = 7 m/s 50 kg H₂=0.40 Hx Problem 3/1
nswer he Toin Ing questions Cry using double itegration method. 1. The beam is subjected to the linearly varying distributed load at segment AB and a uniformly distributed load at segment BC. Determine the maximum deflection of the beam and calculate the slope and deflection at point B. 25 kN/m A C 4 m 3 m El is constant Below is the illustration of an overbangina beam Determine the following:
A 100mm diameter 2014-T6 aluminum axle is subjected to the loads shown. Use Castigliano's method to determine the vertical displacement of point C. Young module 73.1 GP A 1 m C 0.5 m 0.5 m 8 kN 8 kN 1m - B
PROBLEM 3: FORCE AND ACCELERATION The crate has a mass of 80 kg and is being towed by a chain which is always directed at 20 degrees from the horizontal as shown. Determine the crate's acceleration in t=2s if the coefficient of static friction is 4, - 0.4, the coefficient of kinetic friction is uk = 0.3, and the towing force is P = (90t²)N, where Tis in seconds. p 20°
Situation 22: The 125-kg concrete block A is released from rest in the position shown and pulls the 200 kg log up the 30" ramp. If the coefficient of kinetic friction between the log and the ramp is 0.5, compute the following: Sit kp rac fri ca Si 200 kg u HA3D0.5 T 125 kg 6m 30° 1 2 1. acceleration of block A as it hits the ground 2. tension in the cable supporting block A 3. velocity when block A hits the ground
v of 1 10 ft/s B |The 19lb cart B is supported on rollers of negligible size,lf a 7lb suitcase A is thrown horizontally onto the cart at 10 ft/s when it is at rest, determine the length of time that A slides relative to B. The coefficient of kinetic friction between A and B is ?k=0.4.