13.a. Which device is intended for the protection of personnel that functions to de-energize a circuit or portion thereof within an established period of time when a current to ground exceeds the values established for a Class A device? A. GFPE B. ECG C. GFCP D. GFCI 13.b. Only qualified persons are permitted to work on or near energized equipment of ______ or greater. A. 120 V B. 50 V C. 208 V D. 240 V

7.C. Which of the following statements about bonding is true?A. The joint or termination must offer opposition in the circuit for effective electrical connections.B. Effective bonding keeps impedance high if a fault should occur.C. The entire electrical safety circuit is only as good as its strongest bonded link.D. Bonding connections must endure high levels of fault current until overcurrent protective devices can operate. 7.b. Which of the following is required with a low-voltage incandescent lamp that's operating on a standardservice?A. PhosphorsB. Argon gasC. A step-down transformerD. A ballast 7.a. The ordering code for a large incandescent lamp provides information on theA. lamp power requirement, bulb type and size, and sometimes lamp color.B. lamp power requirement, bulb size and special features, and sometimes filament type.C. lamp voltage, bulb type and size, and sometimes lamp color.D. lamp voltage, bulb size and special features, and sometimes filament type.

1. A14/2 type copper used for a general lighting branch circuit.                                                Ampacity:______________              Maximum Fuse or Circuit Breakers Sizes:________________      2.Three 8 AWG copper conductors with THHN insulation Installed in garage in electrical metallic tubing (EMT). The ambient temperature in the garage can reach as high as 110'F. All termination points for this circuit are rated 60'C.                            Ampacity:______________                  Maximum Fuse or Circuit Breakers Sizes:________________ 3.Four 4 AWG copper conductor with THWN insulation imstalled in EMT in a basement. All termination points are rated at 60'C.                                 Ampacity:______________                  Maximum Fuse or Circuit Breakers Sizes:________________  4. An 8/3 Type UF copper cable installed underground from a house to a detached garage to feed a 120/240-volt subpanel. All termination points are rated at 60'C.…

The term "____" is defined in NEC® Article 100 as "connected to establish electrical continuity and conductivity." Select one: A. BENDED (BENDING) B. BONDED (BONDING) C. SHUNTED (SHUNTING) D. GROUNDED (GROUNDING)

A? Conductor is defined in NEC 240.2 as a conductor, other than a service conductor, having overcurrent protection ahead of its point of supply that exceeds the value permitted for similar conductors that are not taps. A. Faulted b. Tap c. Magnetic d. Copper-like

Explain the relevance of earthing and bonding in an electrical Installation.

How is the grounded dc conductor of a photovoltaic system required to be identified? a. shall be identified at the time of installation by distintive red markings on some of the terminations b. shall be identified at the time of installation by distintive blue marking at all terminations c. shall be identified at the time of installation by a distintive grouping of wires AWG #2 d. shall be identified at the time of installation by distinctive white marking at all terminations.

6.a. The amount of short-circuit current that flows depends upon the amperes available at the source ofpower, the length of the circuit, and what other primary factor?A. The presence of a ground fault currentB. Proper installation of the branch circuitC. Presence of no previous damage to the electrical systemD. The size of the conductors and voltage at which they operate6.b. You're evaluating the components of a multioccupancy building that won't have an on-site employee. Tobe compliant with the NEC, each occupant will need to have access to their ownA. service-disconnecting means.B. service conductor.C. cable attachment point.D. emergency fire water-pump disconnect.