(Single Disk Clutch)112The Ratio between the Outside and Inside Diameter of the Disk is100the coefficient of friction is 0.3. Theactuating force is 160 N and the power capacity is 41 hp. If it is to operate at speeds of up to 2000 rpm, calculatethe size of the Outside and Inside Diameter in mm.

Answered: Image /qna-images/answer/48329beb-15dd-4d21-b1c9-ab047cca3e59.jpg

112 he Ratio between the Outside and Inside Diameter of the Disk is 100 the coefficient of friction is 0.3. The ctuating force is 160 N and the power capacity is 41 hp. If it is to operate at speeds of up to 2000 rpm, calculate he size of the Outside and Inside Diameter in mm.

112 he Ratio between the Outside and Inside Diameter of the Disk is 100 the coefficient of friction is 0.3. The ctuating force is 160 N and the power capacity is 41 hp. If it is to operate at speeds of up to 2000 rpm, calculate he size of the Outside and Inside Diameter in mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

While a vehicle with a mass of 2350 kg is moving at 120 km/h, suddenly braking It stops with an acceleration of -9.18 m/s2. There are two brake pads on each wheel of the vehicle. The friction coefficient between the brake pad and the brake disc is 0.3. During braking, assume 20 N/mm2 is the pressure on the brakke pad, find the area of the pad. Safety coefficient will be taken as 3
The mass of block A in Figure 5 is 60 kg. The coefficient of friction between the thread and the mating groove is 0.2 and that between all other rubbing surfaces is 0.4. The pitch of the thread on the shaft is 5 mm. Take the mean radius of the screw to be 15 mm. a. Sketch free body diagrams for the block and the wedge. b. Neglecting the weight of the wedge, determine the force that must applied to raise the block with the wedge. c. Sketch a free body diagram that can be used to determine a relation between the force that can turn the screw, and the minimum force that the screw must exert on the wedge in order to raise block A. d. Using your free body diagram from (c), derive a relation between the force that can turns the screw to push the wedge, and the force the screw exerts on the wedge in order to raise block A. e. Determine the minimum couple that must turn the screw in order to raise block A using the relation you obtained from (d)
Find the value of coefficient of friction if friction force is 200 N and Normal force is 780 N
The band of a brake has a contact angle of 18° deg. If the pulls on the bands are 275 kg and 100 kg, find the coefficient of friction.
answer fast
Do it fast
The coefficient of friction between the cylinder and the brake is 0.3. If the force P applied the brake is 20 N and the length d = 1.0 m, and a brake BC is to be arranged so that the speed of the cylinder may be reduced from 60 rpm to zero in 4 sec. Figure A is a solid cylinder weighing 600 N with a diameter of 0.60m. Find the total length L of BC. In m, 1 metric ton = 1,000kg = 9806.65 N Thirt ܕܗܘ] B d = 1. Om A a L-1 m mm
D B (2 100N AB=10 cm CB=BD=4 cm AF=2cm In the mechanism shown above, the friction coefficient of the sliding limb is given as 0.3. A horizontal force of 100 N is applied from the F point. Calculate the torque required for the AB crank handle to start SYT (Counter Clockwise) motion.
A car has hydraulically operated disc brakes at the front and drum brakes at the rear. The frontbrakes have pistons of 58 mm diameter each, whereas each of the wheel cylinder at the rearbrake has 28 mm diameter. The master cylinder piston has diameter of 40 mm. The brake footpedal has a leverage of 4. If the brake pedal is applied a force of 100 N, Calculate (i) The brakingforce on the front axle, (ii) The braking force on the rear axle.
Find the value of frition if coefficient of friction is 0.3 and normal force is 200 N
The figure below shows the essential parts of a hydraulic brake system. The area of the piston in the master cylinder is 1.8 cm² and that of the piston in the brake cylinder is 6.4 cm2. The coefficient of friction between shoe and wheel drum is 0.50. If the wheel has a radius of 37 cm, determine the frictional torque about the axle when a force of 50 N is exerted on the brake pedal. N. m Wheel drum Pedal Shoe Master cylinder cylinder Brake
What is the formula?? What is the answer??? Need help asap please