The tension, Tiial of V-belt with groove of 60° during initial adjustment is 150 N on each side. The angle of lap is 165° at the smaller pulley while the coefficient of friction between pulley and belt is 0.32. Given the pulley speed is 1500 RPM during operational stage. At the situation where belt is the point slipping on the smaller pulley, (ii) Calculate the tension in each side of belt. (ii) Examine the power transmitted assuming pulley radius is 120 mm.

The tension, Tiial of V-belt with groove of 60° during initial adjustment is 150 N on each side. The angle of lap is 165° at the smaller pulley while the coefficient of friction between pulley and belt is 0.32. Given the pulley speed is 1500 RPM during operational stage. At the situation where belt is the point slipping on the smaller pulley, (ii) Calculate the tension in each side of belt. (ii) Examine the power transmitted assuming pulley radius is 120 mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem: A pump is driven by an electric motor through an open type flat belt drive. Determine the belt specificationsfor the following data.Motor pulley diameter= 400 mmPump pulley diameter = 800 mmCoefficient of friction for motor pulley = 0.30Coefficient of friction for pump pulley = 0.35Center distance between the pulleys=2000 mmRotational speed of the motor=2000 rpmPower transmission = 40kWdensity of belt material = 1000 kg/m3 width of the belt=240mmthickness of the belt = 5mm
A multiple V-belt drive is required to transmit 4 kW. The smaller pulley of the system is150 mm diameter, rotates at 200 rev/min, and has an angle of lap angle of 135°. Thegrove angle is 40° and the coefficient of friction between the belt and the pulleys is 0·3.If the maximum tension in any one belt is limited to 800 N, calculate:(a) The number of belts required. (b) The minimum tension in any one belt. (c) The required pre-tensioning of the belt. The centre-to-centre distance between the pulleys is 2 m.(d) Determine to the nearest mm, the required size for the larger pulley.(e) Find the approximate length of the belt
HW5 The tension in a pulley belt is 30 N when stationary. Calculate the tension in each side and the power transmitted when the belt is on the point of slipping on the smaller wheel, the wheel is 300 mm diameter and the coefficient of friction is 0.4. The angle of lap is 160°. The wheel speed is 1420 rev/Min.
A soft surface cone clutch must handle 1865 In-1b of torque at 1250 rpm. The large diameter of the clu is 13.75 in. and the included angle in 12.5°. The face width of the bearing surfaces is 2.5 in. Using efficient of friction 0.20. determine (a) the force (F) to engage the clutch, (b) the required normal unit pa sure on the contact surfaces when operation is at capacity Ans. 428 lb. 13.15 psi
04/ The contact surfaces in a cone elutch have an eflective diameter of 80 mm. The semi-angle of the eone is 15° and coefficieat of friction is 0.3. Find the tonque required to produce slipping of the clutch, if the axial force applied is 200 N. The clutch is employed to connect an elecric motor, running uniformly at 900 rp.m. with a flywheel which is initially stationary. The flywheel has a mass of 14 kg and its radius of gyration is 160 mm. Cakulate the time required for the flywheel to attain fell-speed and iulso the energy lost in slipping of the clutch.
4.) A flat belt makes contact with an 18 in. diameter pulley through half its circumference. If the coefficient of friction is 0.45, and a torque of 350 ft-lbs is to be transmitted, calculate the belt tensions.
PROBLEM 3 - A scissors-type jack with a single square thread which engages the threaded collar G and turns in a ball thrust bearing at D is being designed. The thread is to have a mean diameter of 10 mm and a lead (advancement per revolution) of 3 mm. With a coefficient of friction of 0.20 for the greased threads, (a) calculate the torque M on the screw required to raise a load of 1000 kg from the position shown and (b) calculate the torque M required to lower the load from the same position. Assume that platform AB and line DG will remain horizontal under load. Neglect friction in the bearing at D. A 45° 45° но 30° 30 30° 30° G 30° 30° • E GI = DI = 160 mm, HI = CI = 80 mm Problem 3
Torsional coil springs in the clutch disc_a. cushion the driven disc engagement rear to frontb. are the mechanical force holding the pressure plate against the drivendisc and flywheelc. absorb the torque forcesd. are located between the friction rings
The following figure shows a belt brake system operating on a brake drum of the hoisting mechanism. It consists of a cylinder with a diameter of 325 mm, the end of which is the elastic belt connected to both ends of the elastic belt by a crank arm articulated at B and the angle of rotation = 225 degrees. And the coefficient of friction is 0.3 and the latching force is f. Find the necessary F to generate a torque of 350 on the cylinder while it is rotating in the direction shown? Note that s = c = 135mm a = 500mm. 35mm
A multi-plate clutch must transmit 11 kW of power without slipping at 1500 rev/min. The coefficient of friction is 0.3. The inner and outer radis are 30 and 85 mm respectively. The axial force applied to the plates is 780 N. Determine the number of plates required using.
Q1 Q5) Determine the principal dimensions of a cone clutch faced with lather to transmit 40 kW at 800 r.p.m. from an electric motor to an air compressor. Sketch a sectional front view of the clutch and provide the main dimensions. Assume that the semi-angle of the cone is 10°, the coefficient of friction is 0.3, mean diameter of cone is (7-10)d, where d is the diameter of the shaft, allowable normal pressure for lather and cast iron is 0.1 to 0.2 N/mm, shear stress 100 N/mm, load factor is 2 and the mean diameter to face width ratio is 6.
A multiplate disc clutch transmits 55 kilowatt of power at 1800 rpm. Coefficient of friction for the friction surface is 0.1. Axial intensity of pressure is not to exceed 160 KN/m2. The internal radius is 80mm and is 0.7 times external radius. Find the number of plates needed to transmit the required torque.