Q10A type K thermocouple with a 30°C reference is used to measure a furnace's temperature from 600°to 700°C. By using Table 10, find out the output voltages corresponding to these temperatures.Table 10: Type K thermocouple51015202530354045-50-1.86-2.03-2.20-2.37-2.54-2.71-2.87-3.03-3.19-3.34-00.00-0.19-0.39-0.58-0.77-0.95-1.14-1.32-1.50-1.68+00.000.200.400.600.801.001.201.401.611.81502.022.232.432.642.853.053.263.473.683.8960024.9125.1225.3425.5525.7625.9826.199 26.4026.6126.8270029.1429.3529.5629.7729.9730.1830.3930.6030.81 31.02

Given Atype K thermocouple Reference temperature is 30°C Furnace temperature is Fromm 600°C to…

10 A type K thermocouple with a 30°C reference is used to measure a furnace's temperature from 600° 700°C. By using Table 10, find out the output voltages corresponding to these temperatures. Table 10: Type K thermocouple 10 15 -2.37 20 25 30 35 -3.03 40 45 -50 -1.86 -2.03 -2.20 -2.54 -2.71 -2.87 -3.19 -3.34 -0 0.00 -0.19 -0.39 -0.58 -0.77 -0.95 -1.14 -1.32 -1.50 -1.68 +0 0.00 0.20 0.40 0.60 0.80 1.00 1.20 1.40 1.61 1.81 50 2.02 2.23 2.43 2.64 2.85 3.05 3.26 3.47 3.68 3.89 600 24.91 25.12 25.34 25.55 25.76 25.98 26.19 26.40 26.61 26.82 700 29.14 29.35 29.56 29.77 29.97 30.18 30.39 30.60 30.81 31.02

10 A type K thermocouple with a 30°C reference is used to measure a furnace's temperature from 600° 700°C. By using Table 10, find out the output voltages corresponding to these temperatures. Table 10: Type K thermocouple 10 15 -2.37 20 25 30 35 -3.03 40 45 -50 -1.86 -2.03 -2.20 -2.54 -2.71 -2.87 -3.19 -3.34 -0 0.00 -0.19 -0.39 -0.58 -0.77 -0.95 -1.14 -1.32 -1.50 -1.68 +0 0.00 0.20 0.40 0.60 0.80 1.00 1.20 1.40 1.61 1.81 50 2.02 2.23 2.43 2.64 2.85 3.05 3.26 3.47 3.68 3.89 600 24.91 25.12 25.34 25.55 25.76 25.98 26.19 26.40 26.61 26.82 700 29.14 29.35 29.56 29.77 29.97 30.18 30.39 30.60 30.81 31.02

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

With calculation, determine what is the input voltage, Vin (+Ve cycle) when the Zener diode D5 starts to conduct current? Show the calculations.
The sudden sizing of voltage to a high peak in very short duration is called O a. Voltage Surge O b. Ober Voltage Oc. Under Voltage O d. Peak Voltage
Q#3 (b) Load current changes from 0-200 m A at 10 v input voltage range from 15 -20v Zener diode stabilized maximum current OF Two digit of your roll number m A Find Rs . shown in figure #3 roll no 52
Assuming ideal diodes, what is the possible output waveform of the circuit?
The source voltage of the circuit is 5V and the break down voltage for the Zener diode is 5.2V then the voltage across resistor will be ??
Determine and sketch the output voltage. R1 +10 V 1.0 kN D Vin 0 out 5v 5 v -10 V + Diodes are IN4001.
Determine the following for the fixed- biased configuration. (Use 4 decimal places) a. IBQ and ICQ b. VCEQ c. VB , VC and VBC
Based on the simulation results, which diodes turn on during the positive half cycle of the input voltage and during the negative half cycle of the input voltage.
Q9 ANSWER THE QUESTION
o': Assuming the ideal diode model (VoN=0 V), calculate VoUT for the cireuits in Figures (b) and (c) for the following input voltages (your answers should be in a table similar to that given below) VIO VIO VOUT,b VOUT,C v20- v20- (b) (c) VI V2 5 5 5
What is the barrier potantial of silicon diode at room temperature?
If three of the same diode were connected in series, what would be the value of the resistor R1?