1. The following data shows the results of the liquid limit and plastic limit test using Casagrande cup method. Calculate the following: (Hint: Solve the moisture content of each test) a. Liquid Limit b. Plasticity Index c. Liquidity Index Liquid Limit Test: TEST NO. No. of Blows Wt. of Wet Soil + Container Wt. of Dry Soil + Container Wt. of Container Plastic Limit Test: TEST NO. Wt. of Wet Soil + Container Wt. of Dry Soil + Container Wt. of Container Natural Water Content: TEST NO. Wt. of Wet Soil + Container Wt. of Dry Soil + Container Wt. of Container 1 35 22.46 g 19.44 g 12.76 g 1 22.10 g 20.42 g 13.07 g 1 17.94 g 14.84 g 7.84 g 2 21 21.33 g 18.75 g 13.06 g 2 21.77 g 20.19 g 13.28 g 2 17.39 g 14.36 g 7.50 g 3 16 21.29 g 18.78 g 13.26 g

1. The following data shows the results of the liquid limit and plastic limit test using Casagrande cup method. Calculate the following: (Hint: Solve the moisture content of each test) a. Liquid Limit b. Plasticity Index c. Liquidity Index Liquid Limit Test: TEST NO. No. of Blows Wt. of Wet Soil + Container Wt. of Dry Soil + Container Wt. of Container Plastic Limit Test: TEST NO. Wt. of Wet Soil + Container Wt. of Dry Soil + Container Wt. of Container Natural Water Content: TEST NO. Wt. of Wet Soil + Container Wt. of Dry Soil + Container Wt. of Container 1 35 22.46 g 19.44 g 12.76 g 1 22.10 g 20.42 g 13.07 g 1 17.94 g 14.84 g 7.84 g 2 21 21.33 g 18.75 g 13.06 g 2 21.77 g 20.19 g 13.28 g 2 17.39 g 14.36 g 7.50 g 3 16 21.29 g 18.78 g 13.26 g

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. Table 2 shows the results of the standard proctor test Water content (%) Weight (kg) 14 16,5 18,5 20 21 22,5 Table 2. Proctor Test Results 1,45 1,71 1,87 1,88 1,76 1,67 If this test uses a sample print with a size of 943 cm^3, answer these questions: a. interpret the results of this proctor test, and determine the optimum moisture content and maximum dry unit weight. (Gs = 2.7)
A constant head permeability test is performed on soil that is 4 cm2, and 2.5cm long. The head difference applied during the test is 20 cm and 7 cm3 is collected over a time of 100 sec. Provide step by step solution. What is the permeability based on these test conditions and results.
Refer to the figure above. For a constant head permeability test in a sand, the following values are given: L = 370 mm A = 125 cm? h = 460 mm Water collected in 3 min Q = 550 cm³ Void ratio of sand e = 0.61 Determine: a. Hydraulic conductivity (Enter your answer to three significant figures.) k = cm/s b. Seepage velocity (Enter your answer to three significant figures.) Vs cm/s
Following are the results from the liquid and plastic limit test for a soil. No. of blows (N) Moisture Content % 16 39.5 20 36.1 28 30.0 a. Compute the liquid limit. b. Compute the plasticity index. C. Compute the liquidity index if the insitu moisture content is 26.5%. d. Compute the consistency index.
I need the the answer as soon as possible
5. A permeameter of 8 cm diameter contains a sample of length 35 cm. Attachments are made it to enable conducting either constant head test or falling head test. The stand pipe used for conducting falling head test has a diameter of 2.5 cm. When constant head test was conducted the loss of head was 100 cm measured on a length of 25 cm. If the rate of flow was 2.7 cc/sec, calculate the coefficient of permeability of soil. If a falling head test is conducted on the same sample in the permeameter find the time taken for head to fall from 150 cm to 100 cm.
the following data have been obtained in a standard laboratory proctor compaction test : Trial No. moisture content. % 1 9 2 3 4 6 11.9 14.6 15-8 19.0 21.6 weight of container and compacted soil 137.43 38.16 38-67 38-8439-06 38.76 (N) The container is 943 cm³ ih volume and its weight is 201 A-Determine the optimum moisture content and the maximum dry unit weight B-what is the dry uhit weight and water content at 95% standard compaction in the field ?
Q1 Data obtained from a laboratory consolidation test are tabulated as follows: Test points I 2 3 4 5 o' (kPa) Total AH (mm) 20 50 100 0.23 0.87 L.90 3.62 5.55 7.25 200 400 800 G,=2.70, Ho= (initial thickness at zero pressure) = 22.5 mm, w = (moisture content at the beginning of the test) = 0.78. Plot the e-logo' curve and calculate Ce Ae I+eo Ho log a - logo, log(o /06) ΔΗ Hint: and
-1 (a) (b) The results shown in Table QA1 were obtained by a group of students during a laboratory experiment using a standard Proctor test on granular material. Table QA1 Bulk density Water content (Mg/m³) (%) 2 5 6 8 9 1.91 2.24 2.31 1.99 1.4 Using the data in Table QA1, plot the corresponding compaction curve and determine the air content corresponding to the optimum water content and maximum dry density for this soil. Is the air content within the range normally specified when at optimum values? (Note you may Assume: Gs = 2.7 and pw = 1 Mg/m³) Explain why and when it is essential to determine soil density on construction sites.
Classify soil A depicted in the table according to the AASHTO classification system. Sieve analysis- Percent finer No. 10 Liquid limit Plasticity index Soil No. 40 No. 200 A 98 80 72 52 21 Select one: a. A-7-5 b. A-7-6 C. A-7 d. A-6
Soil mechanics
The results of a Standard Proctor test are given in the following table. Moist Weight of Wet Sol Moisture Content in the mold (Ib) Trial (%) 26 4.08 28 4.12 30 4 4,18 32 Determine: 1. Maximum dry unit weight in Ib/ft^3 (4 decimal places) 2. Optimum water content in % (4 decimal places)