A course sand sample is placed in the constant permcameter test. What is the coefficient of permeability of the sand in cm/sec if the sample is placed inside a 166 cm container with a 7.44cm o. Consider that the water passes through the sample with a constant head of 40cm and after 6 seconds, 40 grams of water have been collected.

A course sand sample is placed in the constant permcameter test. What is the coefficient of permeability of the sand in cm/sec if the sample is placed inside a 166 cm container with a 7.44cm o. Consider that the water passes through the sample with a constant head of 40cm and after 6 seconds, 40 grams of water have been collected.

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter6: Hydraulic Conductivity

Section: Chapter Questions

Problem 6.7P

See similar textbooks

Similar questions

Problem 4. A sample of sand is tested in a constant head permeameter. The sample diameter is 50 mm and its length is 120 mm. Under an applied head of 60 cm, 113 cm³ flows through the sample in 5 minutes. The Mof the sample is 385 grams. Calculate: a. the Darcy coefficient of permeability (k) b. the discharge velocity (v) c. the seepage velocity (v₁)
A sample of sand is subjected to a constant head permeability test. The sample diameter is 60 mm and its length is 130 mm. Under an applied head of 60 cm, 119 cm³ of water flows through the sample in 5 minutes. Determine (a) the coefficient of permeability, and (b) the discharge velocity.
For a constant head laboratory permeability test on a fine sand, the following are given: Length of specimen = 250 mm Dia. of specimen = 62.5 mm Head difference = 450 mm Water collected in 2 min. = 484 cu.mm Determine the discharge velocity in mm/sec. 0.0789 mm/sec 0.001315 mm/sec 4.734 mm/sec 0.0438 mm/sec
PART IV: PERMEABILIT Y PROBLEM A For a constant head laboratory test on a fine sand, the following are the given values : • Length of the specimen • Di ameter of the specimen 14.0 inches 3.25 inches He ad difference 25.0 inches Water collected in 2.50 mins Void ratio A. Compute for the hydraulic conductivity of the soil in in/sec. B. Determine the discharge velocity through the soil in in/sec. c. Determine the seepage velocity in in/sec. 0.065 cubic inches 0.45
Show calculation on how to determine the average coefficient of permeability of the sand sample at 20°C. Also show calculations on how to determine the discharge the K1 and Average K1
Problem Set 2: 5. A cubical sample of San Francisco Bay mud (a soft marine silty clay) has been prepared for testing in a true triaxial device. The dimensions of the sample are 76 mm by 76 mm by 76 mm. The sample has a moisture content (w) of 68.5% and a moist density (r) of 1.44 g/cm³. The average specific gravity of solids (G,) is 2.55. Determine (a) the void ratio (e) and degree of saturation (S), (b) the moist density (g) and moisture content (w) if the soil becomes saturated at the same total volume, and (c) the density (p) of the soil if all pore fluid is dried off with no change in total volume. Provide the Phase Diagram.
A dry sand is placed in a ontainer having a volume of 0.366 ft8. the dry weight Of the sample is 34.41b. A volume OF 0.0522 ft3 container so as not to dist urb the condition of the sand 3. OF water is care Fu lly added to the to if the Specific gravity of sand is 2662, determine the. a.) porosity b) Degree of saturation (2 decimal places) c) Bulk specific gravity (3 dlecimal places) (3deuimal places)
← Darcy' Law A sand sample of 35 m² cross sectional area and 20 cm long was tested in a constant head permeameter. Under a head of 60 km, the discharge was 120 ml in 6 min. The dry unit weight of sand used for the test was 1120 g. and GS = 2.68 Take Sw = 1 g/ cm³ The hydraulic conductivity (in cm/sec) is × 10-³ X
A cylindrical soil sample 50 mm in diameter and 200 mm in height is used as thepermeameter in a falling head permeability test setup. In one minute of observation, thehydraulic head in the 10 mm diameter standpipe through which test water went reducedfrom 900mm to 500 mm. During that time, 1.5 liters of water were collected in the graduate. Calculate the soil sample's permeability coefficient in cm/s.
The following results were obtained from a liquid limit test on a clay using the Casagrande cup device. Number of blows 12 20 28 32 Water content (%) 52.5 47.1 43.2 38.6 37.0 Two determinations for the plastic limit gave water contents of 22.8% and 23.2%. Determine (a) the liquid limit and plastic limit, (b) the plasticity index, (c) the liquidity index if the natural water content is 38% and (d) the void ratio at the liquid limit if G, = 2.7. (e) What is the soil state in the field? (f) Do you expect a brittle type of failure for this soil?
2. A constant head laboratory permeability test an o fines and gives the following values Length of specimen - 254 mm Diameter of specimen -63.5 mm Head difference=457 mm Water collected in 2 min -0.51 cm^3 Determine these values o. Hydraulic conductivity, k, of the soil (cm/sec) b. Discharge velocity (cm/sec) c. Seepoge velocity (cm/sec) The void ratin of the soil specimen is 0.46.
Afalling head permeability test was performed on a sample of clean uniform sand. The initial hydraulics head was 900 mm, the final head was 400 mm, 60 sec were required for the water level in the standpipe to fall. The cross-sectional area of the standpipe was 100 mm2. The sample was 40 mm in diameter and had a length of 180 mm. Determine the coefficient of permeability in Darcy's Law.