Type 11/111 sedimentation analysis: A laboratory settling test was performed on a suspension exhibiting flocculent settling characteristics with the results given in the following table. The initial TSS concentration of the suspension was 400 mg/L. Time, min 20 30 TSS concentration at indicated depth 0.5 m 1.0 m 1.5 m 2.0 m 156 286 210 290 116 118 180 210 112 118 156 10 76 108

Type 11/111 sedimentation analysis: A laboratory settling test was performed on a suspension exhibiting flocculent settling characteristics with the results given in the following table. The initial TSS concentration of the suspension was 400 mg/L. Time, min 20 30 TSS concentration at indicated depth 0.5 m 1.0 m 1.5 m 2.0 m 156 286 210 290 116 118 180 210 112 118 156 10 76 108

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter4: Plasticity And Structure Of Soil

Section: Chapter Questions

Problem 4.8P

See similar textbooks

Similar questions

The following results of a falling head permeability test. Calculate the permeabilityof the soil sample Diameter of sample: 100 mmDiameter of feeder pipe: 20 mmLength of sample: 500 mmFlow through the sample: 1.3 l/sDistance between tappings: 450 mmHead loss: 1650 mm
Ciectical Cnyineers GToup as Cv= 40.32% The following data represent the results obtained from the specific gravity (S.G.) test performed ina soil laboratory including * ?for sand samples. Find the mode Number of Specific Gravity 2.30-2.39 Samples 2.40-2.49 4 2.50-2.59 6. 12 2.60-2.69 2.70-2.79 14 2.80-2.89 3.35-3.40 2.10-2.15 2.20-2.25 2.70-2.75 2.80-2.85 2.30-2.35 2,60-2.65 2.40-2,45 2.50-2.55 2.90-2.95 ارفع اجابتك بشكل ملف wdf او صورة 1O 0O O O O O O
The table below shows the results of CU test for a soil sample (h=76 mm, and D= 38 mm), Find the X value, if you know the decrease in VO=2.5 % in consolidation stage. Shearing stage (ho=75 mm) Axial dial gauge reading (F=0.01 mm/div.) Corrected area mm 30 75 120 no one O 1133 mm2 1105 mm2 O 1110 mm2 O 1176 mm2
Geotechnical Engineering (UPVOTE WILL BE GIVEN. PLEASE ANSWER THE QUESTION CORRECLTY. NO LONG EXPLANATION NEEDED. FOLLOW THE INSTRUCTIONS CAREFULLY.) A moist soil weighed 895 g with a volume of 425 cm3. After drying, the sample weighed 775 g. Of the dried soil, 400 g was poured into a vessel loose state. Its volume subsequently determined to be 275 cm3. That same 400 g was then vibrated and tamped to a volume of 212 cm3 with Gs = 2.71. Determine the designation of the granular soil based on its relative density. (3 decimal places - Do not round off unless it's the final answer)
pls ans soon as posssible During a constant head permeability test on a sand sample, 260ml of water was collected in 2 min. If the sample had a length of 100 mm, a diameter of 40 mm and a maintained head of 200 mm, what is the coefficient of permeability?
Geotechnical Engineering (UPVOTE WILL BE GIVEN. PLEASE ANSWER THE QUESTION CORRECLTY. NO LONG EXPLANATION NEEDED. FOLLOW THE INSTRUCTIONS CAREFULLY.) A moist soil weighed 895 g with a volume of 425 cm3. After drying, the sample weighed 775 g. Of the dried soil, 400 g was poured into a vessel loose state. Its volume subsequently determined to be 275 cm3. That same 400 g was then vibrated and tamped to a volume of 212 cm3 with Gs = 2.71. a. Determine the relative density of soil in %. b. Determine the designation of the granular soil based on its relative density.
Problem C: For Questions 12 to 15. Following are the results from the liquid and plasticlimit tests for a soil. Liquid Limit Test Number of Moisture Blows,N Content (%) 16 42.150 20 40.775 28 39.115 12) From the flow curve what is the liquid Limit ? a) 39.683% b) 40.555 % c) 38.992 % d) 39.875 % 13) If the Plasticlimit is 18.750 % what is its plasticity index? a) 22.431 % c) 21.344 % b) 20.918 % 14) If in-situ moisture content is 31% determine its liquidity index ? c) 0.585 d) 20.819 % a) 0.665 b) 1.59 15) If the percentage of clay-size fraction is 4.831. Based on its Activity,this mineral is more likely to be a) Illites b) kaolinite d) 20.588 c) Attapulgite d) Smectites
Problem Set 2: 5. A cubical sample of San Francisco Bay mud (a soft marine silty clay) has been prepared for testing in a true triaxial device. The dimensions of the sample are 76 mm by 76 mm by 76 mm. The sample has a moisture content (w) of 68.5% and a moist density (r) of 1.44 g/cm³. The average specific gravity of solids (G,) is 2.55. Determine (a) the void ratio (e) and degree of saturation (S), (b) the moist density (g) and moisture content (w) if the soil becomes saturated at the same total volume, and (c) the density (p) of the soil if all pore fluid is dried off with no change in total volume. Provide the Phase Diagram.
Prob. A falling head permeability test was performed on a sample of silty sand. The time required for the head to fall in the standpipe from the 60 cm to 30 cm mark was 70 minutes. The sectional area of the standpipe was 1.25 cm?. If the height and diameter of the sample were respectively 100 mm and 90 mm, determine the value of K.
A cubical sample collected from Lobo shoreline (a soft marine silty clay) has been preparedfor testing in a true triaxial device. The dimensions of the sample are 78 mm by 78 mm by 78mm. The sample has a moisture content (w) of 68.5% and a moist density (ρ) of 1.43 g/cm3.The average specific gravity of solids (Gs) is 2.55.Determine(a) the void ratio (e),(b) the degree of saturation (S),(c) the moist density (γ),(d) moisture content (w) if the soil becomes saturated at the same total volume;(e) the density (ρ) of the soil if all pore fluid is dried off with no change in totalvolume.
For a constant head laboratory permeability test on a fine sand, the following are given: Length of specimen = 250 mm Dia. of specimen = 62.5 mm Head difference = 450 mm Water collected in 2 min. = 484 cu.mm Determine the discharge velocity in mm/sec. 0.0789 mm/sec 0.001315 mm/sec 4.734 mm/sec 0.0438 mm/sec
Classify the soil sample using AASHTO Classification System. Passing No. 10 = 89 % Passing No. 40 = 64 % Passing No. 200 = 48 % Plasticity for the minus No. 40 fraction: Liquid Limit = 36 % Plastic Limit = 27 % O GI = 2.0 O A-6 (2) O A-5 (0) O A-4 (2) O A-7-5 (0) O GI = 1.0 O GI = 0