1. Show how to implement 32K× 16 EPROM using two 32K×8 EPROM? 2. List the pins related to the interrupts
Q: 1- Design a 3-bit UP-DOWN synchronous counter such that the UP or DOWN counter is selected by a…
A: The state diagram for the UP-DOWN synchronous counter is shown in the below figure.
Q: Logic Gates: * 7404LS (NOT) * 7408LS (AND) * 7432LS (OR) * 7400LS (NAND) * 7402LS (NOR) * 7486LS…
A: Given: The logic gates given are, The truth table for 2-1 multiplexer is asked and circuit diagram…
Q: a.Write the addressing modes of the following instructions: (i) MOV A, @R0 (ii) MOVX @DPTR, A (iii)…
A: The addressing modes of the following instructions are: MOV A, @R0 = Register Addressing Mode ( In…
Q: Mention number of FETs for following logic operation: a) 3 input NAND b) 3 input AND c) 2 input OR…
A: A) 3 input NAND- 6 FET
Q: 4. A 4-input MUX is shown on the left below. The logic gate diagram is shown below it, FYI. For the…
A: For the given multiplexer circuit we have to complete the timing diagram
Q: 4. FIGURE 1 shows how a 3 to 8 line decoder (TTL 74138) can be used in conjunction with NAND gate…
A: From the above question, we need to calculate a Address of the address bus in order to read the…
Q: 2- Given a BCD decade counter, show the decoding logic required to decode each of the following…
A: (a) For getting HIGH output when the counter counts 0110, the decoding logic needed for decoding the…
Q: Design a 16K × 8 memory using (a) only 2K × 4 memory modules. (b) only 1K × 8 memory modules.…
A: 16K × 8 memory- Based on input, 16k is the memory location with 8 bits(1byte) of data storage at…
Q: ii. Assuming you were tasked to create a Gray Code to BCD converter, design a truth table to…
A: Gray to BCD conversion:
Q: PAL, both AND gate ay and OR gate array are programmable.
A:
Q: Using 64×8 ROM chips with an enable input, construct a 512×8 ROM with eight chips and a decoder.
A:
Q: QUESTION1: After the instructions 'MOV IE, #83H’ and 'MOV IP, #01H’ being executed, what interrupt…
A: Once the instruction “MOV IE #83H” is executed. MSB enables all the interrupts. The IE register will…
Q: Determine what the binary output is for a 6-bit SAR ADC that is connected to a 5V system measuring a…
A: In this question, Determine the digital output of the given input voltage Vi= 2.34V And reference…
Q: Realize the following function ; " on the image " using a (a) 4-to-1 multiplexer, and draw the…
A:
Q: (Short-answer Question) Given a BCD decade counter with only the Q outputs available, show what…
A: (a) For getting HIGH output when the counter counts 0110, the decoding logic needed for decoding the…
Q: (a) Draw the logic diagram of a 3 × 8 decoder using two 2 × 4 decoders
A: Solution: To implement 3×8 decoder using 2×4 decoder, 2×4 decoder must contain an enable input. The…
Q: Design a 4-bit counter that counts in Excess-3 code. The counter should count to (6)10 and then…
A: We need to design a 4-bit counter that counts in Excess-3 code. The counter should count to 610 and…
Q: An excessive current that flows from the logic 1 output of a device to the logic 0 output of…
A:
Q: a) The input section includes the _ Land the_ b) The decision-making functions are completed by the…
A: Figure shows a digital circuit to compare the values from a keypad and light sensor. If both numbers…
Q: Question 2: A. Choose one of the given four words or numbers to match the blanks in the sentences:…
A: We are authorized to answer only 1 question at a time since you have not mentioned which question…
Q: 3-Using only NOR gates to produce the logic functions of: a-OR gate b - NOTgate c - ANDgate d-NAND…
A: As per Bartleby guidelines we are allowed to solve only one question,please ask the rest again.
Q: What is the modulo of the circuit below? 2. Make a table of the count sequence. 3. A BCD counter can…
A:
Q: TRUE or FALSE 1. A NOR gate output is LOW if any of its inputs is LOW. 2. A NOR gate and an OR…
A: In this question we will find outputs of NAND, NOR ,AND gate...
Q: 1 Use feed - forward structure, and check the correctness of weight coefficient for the logic gate…
A:
Q: QUESTION 46 How many different types of interrupt service routines (ISRS) can be supported by the…
A: Interrupt: It is an external event that informs a CPU that a device needs service. During execution…
Q: Discuss with timing diagram the operation of a 3-bit Asynchronous Counter.
A:
Q: 8 LEDS are connected to PORTD of PIC16F microcontroller, so that "1" on an output pin causes he…
A: Here i am providing the answer .Hope it helps. Please like. It helps me a lot. Thank you.... For…
Q: Using appropriate diagrams, explain how a combination of transistors and resistors would be used to…
A:
Q: What is the simplified algebraic expression for the logic gate shown? X xa Y OX + Y OX.Y OX.Y ΟΧΘΥ…
A: Given, The logic gate,
Q: draw and identify or explain Make na input circuit using a switch and an external pull-up resistor.…
A: Pull up resistor can be used in following two ways- When pin is to be used as an input pin, we use…
Q: 10 Which of the following elements belong in transistor level abstraction? (select all that apply)…
A: Following elements are the abstraction level in transistor : 3. Memory : A memory is an abstraction…
Q: Short-answer Question) Given a BCD decade counter with only the Q outputs available, show what…
A: for the given BCD decade counter with only the Q outputs, given that, (a) 0001 (b) 0011 (c) 0101…
Q: In the following statements one of them is not true A sequence of microinstructions is called a…
A: A microprocessor is a device which used for data processing and control logic. It contains…
Q: When the ROM sends data to the microprocessor, which of these conditions are true? a. (RD)' signal…
A: Since ROM are the chips that are attached externally to the microprocessor. And if the ROM is…
Q: Design a\ Up Down Counter that counts from 0 to 7 up and 7 to 0 down by using JK flip flop and…
A: The state diagram is given as: Consider an input, x. When the input is low, the counter acts as…
Q: Which of the following logic gates have only one I/P and one O/P? O a. AND GATE Ob. NOT GATE Oc.…
A: The Answer is NOT gate and is explained below in detail.
Q: 5) Realize the following functions using decoder and logic gates. a. Implement f(w1,w2,w3) = m…
A: If we take OR of the outputs of the active high decoder, it gives the SOP form of the function, F.…
Q: Design a 6x64 decoder using only 3x8 decoders with the help of block diagrams.
A: One 3x8 decoder can give 8 outputs,So if we have 8 of them, we will get 8*8 outputs, that is, 64…
Q: 1. Four 1KB EPROMs are used to make a 4KB memory. How many address lines are needed for each…
A: Address of last memory is given by, 4KB =4×250=1000H Base address is given by, Bse address = E4000H…
Q: 4. FIGURE 1 shows how a 3 to 8 line decoder (TTL 74138) can be used in conjunction with NAND gate…
A:
Q: Problem #2: A synchronous counter counts up to 211. a) What is the MOD number of this counter? b)…
A: (a) Modulus(MOD) is the total number of the clock pulses that can be counted by the counter. so, Mod…
Q: INPUT OUTPUT A AND NAND OR NOR XOR XNOR 1 1.
A: Logic gates are used for logical calculation or logical expressions when we are provide binary…
Q: In peripheral mapped I/O interfacing, the I/O devices are treated differently from memory chips.…
A: Solution- The input and output devices are activated through the control signals I/O read (IOR ) and…
Q: An alarm circuit is composed of 3 switches namely switch A, switch B, and switch C. The alarm…
A: The alarm circuit can be made by using NAND gates NAND gate - A NAND gate (NOT-AND) is a logic gate…
Q: Prove the equality of the following boolean expression (AB)'.(CD)'=(AB+CD)'.state this…
A: to prove the Boolean expression (AB)'.(CD)'=(AB+CD)'
Q: If a 10-bit ring counter has an initial state 1101000000, what is the state after the ?second clock…
A: We need to find out the output state of ring counter
Q: Design 6 lines to 64 lines Decoder using IC# 74138. You can use other logic gates/IC, if necessary.
A:
1. Show how to implement 32K× 16 EPROM using two 32K×8 EPROM?
2. List the pins related to the interrupts
Trending now
This is a popular solution!
Step by step
Solved in 3 steps with 2 images
- The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).Noise margin is the amount of O a. noise voltage that a logic gate can tolerate O b. signal voltage that a logic gate can tolerate O. both signal and noise voltage that a logic gate can tolerate O d. None of the choices are correct
- (a) Consider the flipflop circuits below: (i) Name the 2 circuits given in the figure. Explain how they are different from each other. a. b. (ii) Choose from the list the input that triggers data to travel to the next flipflop in a counter. A: Input at top NAND gate B: Input at bottom NAND gate C: Clock input clk QIn a 4-bit ripple up-counter how many clock pulses will you apply, starting from state 0 0 0 0, so that the counter outputs are as follows? (a) 0010 (b) 0111 (c) 1001 (d) 1110d) Calculate the noise margins for a logic gate with the following logic levels: VIL = 1.0 V, VIH = 3.7 V, VOL = 0.4 V, VOH = 4.4 V.
- ehcu.org/pluginfile 100% 10 / 11 locations, count how many times is 0 and how many times 1 is. Questions:- 1- Write a program in assembly language to perform the following logic ci BL CL DL [5100]- 2- How we can perform the NEG and NOT instructions by using different instructions. 3- Write the following program by using different instruction or instructions for each instruction on the program. MOV AL , 00 MOV BX , FFFF XOR CL , FF NEG BYTE PTR [DI] AND CX , LG. (A-)Hand trace the execution of the following program fragments showing what happens to the flags and registers (AL, BL, CL) in each statement supposes that the flags are initially 0. MOV BL, 03H CF SF ZF OF PF AF ADD BL, 02H SUB BL, 05H MOV AL, 00H DEC AL XCHG AL, BLQuestion 2 Given Vcc=12V, at first the voltage inputs at Pin 6 and Pin 2 are both 10V. Decide the output state at Pin 3 after the voltage inputs at Pin 6 and Pin 2 drop to 6V. VCC CONTROL RESET DISCHARGE O VOLTAGE 8 COMPARATORS DISCHARGE TRANSISTOR THRESHOLD Q VOLTAGE I DIVIDER I OUTPUT OUT TRIGGER OUTPUT FLIP-FLOP GND
- In IC 74153,the input at pin number 14 is Options A-Connected to ground B-Connected to power/VCC C-Connected to LOGIC State D-Connected to LOGIC ProbeLOGIC GATE ( NEED ONLY HANDWRITTEN SOLUTION PLEASE OTHERWISE DOWNVOTE).d) Draw the schematics of 4-bit synchronous and asynchronous MOD-8 counters and comment on their pros and cons. e) Calculate the noise margin for a logic gate with the following logic levels: VIL = 1.1 V, VIH = 3.2 V, VOL = 0.6 V, VOH = 4.0 V.