1. Four 1KB EPROMs are used to make a 4KB memory. How many address lines are needed for each EPROM? Design an address decoder circuit.
Q: B-Given the Fourier transform X(f) of x(1), How would you obtain Fourier transform of x² (1) ?
A: In this question we need to find a Fourier transform of the signal x2(t)
Q: Q1) For the circuit shown in fig.(*), the supply current is i=10+ 4sin500t + 2sin1500t A Find the is…
A:
Q: Q3) Draw the output waveform for the circuit in figure below. Assume that +Vout(max) = +10 V and -…
A: By knowing the property of zener diode and operation amplifier we need to plot output waveform of…
Q: Find the overall susceptance across terminal a-b when Vs = -2 sin(4t + 310°) V. ΖΩ 4 H ΖΩ a mm ww Vs…
A: In this question we will find overall susceptance across terminal ab in given question...
Q: (C)- Draw the mechanical characteristic of shunt and series DC motors.
A: DC series motor: The armature & field windings of series DC motor are connected in series with…
Q: - has greatest 1. By the comparison among pipeline, superpipeline, and superscalar. The speed up…
A: Since you have posted a question with multiple sub-parts, we will solve first three subparts for…
Q: Q1: Plot the Bode for the following system using the Tabulation method on the attached log paper (s…
A:
Q: Draw a diagram for astable multivibrator using 555 timer. Find the oscillation frequency of the…
A:
Q: ii) Find IDTFT of X(ejw)= е-jw/² for - <<
A: Given: IDTFT of Xejω=e-jω2 -π<ω<π
Q: Q3: Answer briefly: 1. A certain BJT amplifier exhibits three critical frequencies in its low…
A: We are authorized to answer one question at a time, since you have not mentioned which question you…
Q: A load of 240 + j 120 is connected to a source of 480 V with a phase angle of 30o, through a…
A:
Q: the relation between armature and field currents in a series connected DC motor is O It = If + la O…
A:
Q: b +CC W1 +PC- 6V 3A 15V + PC- +CC W2 Wattmeter W1 reads 75 W Wattmeter W2 reads 60 W Determine the…
A:
Q: Use the mesh-current method to find the steady- state expression for v, in the circuit seen in Fig.…
A:
Q: Needed to be solved correctly in 30 minutes and get the thumbs up please show neat and clean work .…
A: In this question we will find susceptance of given circuit across ab....
Q: Planes x = 2 and y = - 3, respectively, carry charges 10 nC/m^2 and 15 C/m^2. If the line x = 0, z =…
A: Let E=E1+E2+E3 Where, E1, E2 and E3 are, respectively, the contributions to E at (1,1,-1) due to…
Q: In the below given figure, two capacitances are in series with a 18V source. The capacitance of the…
A:
Q: Q2:- Find vo(t) for t> 0 in Figure below: 6 kn 1=0 ofo 9V 6 kn www (1) 2.5 μF Fig. (2) www 6 km) O 2…
A: In this question, We need to determine the voltage across the capacitor C? We know Capacitor act…
Q: Find R₁, R₂, and R3 in the following figure when the value of fuse is 20 mA. 5.6 V www R₁ P₂ = 22 mW…
A: Given, Fuse rating is 20 mA.
Q: In the below given figure, two capacitances are in series with a 18V source. The capacitance of the…
A: In this question, We need to solve the voltage across the capacitor C2 . We know Charge Q= CV
Q: Draw a diagram for astable multivibrator using 555 timer. Find the oscillation frequency of the…
A:
Q: Draw the output waveform on the top of the input waveforms for this circuit, Assume that +Vout(max)=…
A: In this question, We need to draw the output waveform of the given operation amplifier. We are…
Q: Find the overall susceptance across teminal a-b when Vs = −2 sin(4t + 310°) V. 22 4H 22 a w Vs b 1 2…
A: In this question we will find overall suceptance across ab in given network...
Q: Let G(s) = -K(s + 1)² s² +2s +2 with K > 0 in Figure P8.3. [Sections: 8.5, 8.9] a. Find the range of…
A: Given G(s)=-Ks+12s2+2s+2 with K>0. a. We need to find the range of K for closed-loop stability.…
Q: )magnetic flux density (B).(2)magnetic field intensity (H),(3)current density (J).
A: Magnetic field - This line which shows the interaction between the movement of electric charges and…
Q: 1. The circuit below shows a three-phase system with two loads. The delta-connected generator has a…
A: Three phase system is transmission of bulk power of transmission. It consist of three phase voltage…
Q: Find Vo in the circuit using nodal analysis. Will upvote immediately
A: In this question, We need to determine the voltage Vo using the nodal analysis.
Q: A given AM broadcast station transmits an average carrier power output of 40 KW and uses a…
A: The power of the carrier wave is given by the expression as shown below: Pc=12Ac2R Plugging the…
Q: Q2) show that: a) ſªx(t)dt ↔ X(f) + X(0)8(ƒ) 2πJf 2 b) if x(t) = x(-t) (even symmetery) then all the…
A: For the above given equations we need to derive them by the help of fourier transform and fourier…
Q: 3. (a) Prove that the maximum efficiency for series-fed and transformer coupled class A power…
A: Given: To prove that maximum efficiency for series-fed and transformer-coupled class A power…
Q: one of these vectors is an impossible electrostatic
A:
Q: Find VR (t) for all time t. 4 V 202 ww 115 HH t=0 t=0 2 H + > VR 2 Ω
A:
Q: |► Q)3(b) Draw the bode plot of G(S) = Sn
A:
Q: 2/ Find dyl da of the following function tan (tanka) у=
A: Given data, y=tan-1tanhx tany=tanhx............eqn 1
Q: How Get = S+2 Rind the first order in control system and draw
A: Important Notes about first order system First order system can be described by first order…
Q: 2. For the following causal system y(n) = x(n-1) − x(n-2) + 1.6y(n-1) - 0.64y(n-2) Determine the…
A: For the given causal system, the transient and steady state response for the input x(n) = 2u(n) are…
Q: For static (time-independent) fields, which of the following current densities are possible? (a) J =…
A: We need to check whether the given field are static or not
Q: A/ Find the output of the system shown below: Signal Response g(t) System When the f(t) = Asinī…
A: In this question, We need to determine the output of the given system? We are solving this problem…
Q: A 20 KVA, 2200/220 V, 50 Hz, single phase transformer gave the following reading: O.C. Test: 220 V,…
A: In this question we need to find voltage regulation , maximum efficiency and equivalent circuit…
Q: Use the concept of source 4Ω ΜΑ 20/0° V to find Vo 14 Ω m -201₂ Ω transformation -j3 Ω ΠΩΕ ΖΩ
A:
Q: Q1. For the forward transfer function plot the root locus K 15² +1$+$ G(s) = Ls+b s(s+3)(s+6) 154…
A: Given,For a unity feedback control system,The forward transfer function is,Gs=Kss+3s+6
Q: Example 10. A 3300/230 V, 50-kVA, transformer is found to have impedance of 4% and a Cu loss of 1.8%…
A: In this question we will find percentage reactance and ohmic value of resistance , reactance and…
Q: (2) An 8 bit successive approximation analog to digital converter has full scale reading of 2.55 V…
A: Given 8 bit SAR A to D converter. Full scale reading = 2.55 V Conversion time for input of 1V = 20…
Q: A drone is receiving a signal from the command and telemetry system, find the amplitude of the…
A: For the above given magnetic field and magnetic flux density we need to calculate the value of…
Q: Planes x = 2 and y = - 3, respectively, carry charges 10 nC/m^2 and 15 nC/m^2. If the line x = 0, z…
A: Charge density determine the how much charge stored in a field. Charge density measure in term of…
Q: In the single-phase, three- winding, transformer, the primary current is equal to lo at the…
A: In this question we need to choose a correct option
Q: (c) Design a comparator circuit using an op-amp and LED as indicator altogether with necessary…
A: Operational amplifier is a analog cirvcuit it takes differential voltage as input and gives the a…
Q: * A circular ring of radius (a) carries a uniform charge pL C/m and is placed on the zy-plane .the…
A: It is given that: A circular ring of radius (a) carries a uniform charge ρL C/m and is placed on the…
Q: Q2 i) a) b) Find DTFT of X[n] = 8[n+5] -a" 8[n-5] X[n]=(n-1) (1/3)^ u[n]
A:
Q: QUESTION 1 A6 pole synchronous motor powered from a 60 Hz voltage source operates at what speed…
A: Given a synchronous motor has, Number of pole, P = 6 Frequency, f = 60 Hz
1. Four 1KB EPROMs are used to make a 4KB memory. How many address lines are needed for each EPROM? Design an address decoder circuit.
Trending now
This is a popular solution!
Step by step
Solved in 2 steps with 1 images
- 4) Design and draw these memory units with their control circuits. Explain operations. a) A single EPROM 2716 is used with an 8088 microprocessor so that this microprocessor will see only X bytes of memory between the address range of DF800 –DFFFF or DD800 - DDFFF instead of 1M byte that it expects. Draw this circuit. What are X bytes? Do not use 74138 decoders. b) Design and show a 16K x 16-bit memory circuit by using 8K x 8-bit RAMS. Explain its operation. Do not use decoder 74138 chip.a.Write the addressing modes of the following instructions: (i) MOV A, @R0(ii) MOVX @DPTR, A (iii) MOVC A, @A+DPTR (iv) MOV R0, #45H b) Write instructions to perform the following operations: (i) Move the content of Accumulator to register 7(R7).(ii) Move the contents of RAM memory location 55H to Port 1(iii) Receive content from ROM Memory location 200H into Accumulator.(iv) Clear bit 7 of the Accumulator.c) Why 4-20mA Current loop is widely used Industrial Standard for sensor data transmission and control. What are its advantages over 0-12V Standard? d) Two configurations of GPIB is shown in Fig. A and Fig. B. Explain the working of GPIB in both the configurations and what are the differences between the two. this question is asked in microcontroller and microprocessor2. A microprocessor has a memory space of 4 MB. Each memory address occupies one byte. a) What is the address bus size (number of bits needed for addressing) of this microprocessor? b) What is the range (lowest to highest, in hexadecimal) of the memory space for this microprocessor? c) Complete the memory map by the address ranges (lowest to highest, in hexadecimal) 8 bits for each memory chip. 0x 0x 0x 0x 0x 0x 0x 0x Address 0 1MB 1MB 1MB 1MB
- Draw the figure for memory segments with 8086 microprocessor software model. Explain the logical address structure used for each segment (Explain which registers are used in logical address presentation of each segment; segment address : offset address). Give an example solution to find the physical address in a segment from the logical address for 8086 microprocessor.8085 microprocessor went through its manipulation operation in the ALU, the results was transferred on the data bus and status of the results was stored in the flag register for indications . With your knowledge and understanding illustrate a complete bit configuration of 8085 flag register and show the functions of the represented bits in the register.1. How do the data retention characteristics of RAM and ROM storage devices differ? 2. What is the purpose and use of the Program Counter (PC), Stack Pointer (SP), and Memory Address Register (MAR) registers? 3. Write an 8085 program to store 4EH in memory location 2840H and store 3EH in memory location 2841H, exchange them and store the result in memory locations 2842H and 2843H respectively. Solve this problem using three different methods. 4. Write a program to exchange the content of memory locations [2801] [2800] with [2803] [2802]. 5. The following program is supposed to add the contents of memory location 2050h to the Accumulator. The program works correctly only part of the time. Show that it is wrong to execute the program and how to correct it. MOV LDA ADC HLT В.А 2050H в 6. In a multibyte addition program, when you must use the ADD instruction? When you must use the ADC instruction? 7- The 8085-instruction set does not include a clear accumulator instruction. Which…
- 2. a) Draw the figure for memory segments with 8086 microprocessor software model. Explain the logical address structure used for each segment (Explain which registers are used in logical address presentation of each segment; segment address : offset address).Q1) List the main internal elements of a microcontroller. And explain the function of each of them. Q2) What is the difference between the Von-Neuman Microcontroller Architecture and Harvard Microcontroller Architecture. Q3) Compare between the (EEPROM) and the Non-Volatile RAM - (NVRAM). Q4) What is the term “Complex Instruction Set Computer(CISC)” mean in the Microcontroller Architecture.3. Given the following memory chip configurations find the requested information: EPROM with 14 address lines (pins) and 8 data lines (pins). What is the chip capacity (include units)? What is the chip organization? Volatile or Non-volatile (circle one) SRAM with 18 address lines (pins) and 4 data lines (pins). What is the chip capacity (include units)? What is the chip organization? Volatile or Non-volatile (circle one) NV-RAM with 10 address lines (pins) and 4 data lines (pins). What is the chip capacity (include units)? What is the chip organization? Volatile or Non-volatile (eircle one) DRAM with 13 address lines (pins) and 1 data lines (pins). What is the chip capacity (include units)? What is the chip organization? Volatile or Non-volatile (circle one) If the memory chip below is used in a system with a 16-bit address bus, then address lines A13 – A15 would need to be decoded externally. Find the address range for each of the possible decoding combinations (000, 001, 010 ... 111)…
- b) Explain how to find the physical address in a segment from the logical address for 8086 microprocessor.Given a 8-bit number at memory location 2050H. Write 8085 instruction to move the value stored at the following locations: Register B Accumulator 2052H Write a single program and show register and accumulator screenshot and also attach memory view. In sim8085 software.A question about 74LS04 IC (a Schmitt Trigger). The pictures show the 74LS04 logic, the connection required and data sheet. Question a)In order to light up the LED, what should Pin 1 and Point A connected to? Ans: Pin 1 connected to (5V / GND), Point A connected to (5V / GND). b)In this example, the power that lights up the LED comes from where? c)What is the current shown on the multi-meter? Is the current flowing out from Pin 2 or flowing into the Pin 2?