1. Maverick and Goose are flying a long-range stealth mission and they must prioritize power usage to their critical systems. See the circuit below: EF-14 2.4 KV Misc. Systems RMisc 14.2 ΚΩ Critical Systems RCrit 7.8 ΚΩ a) What is the power used by the critical systems? b) What is the efficiency of the power delivered to the critical systems compared to the total power the aircraft is using? c) Efficiency needs to be changed to 100% to complete the mission by changing the value of the Misc. Systems. Redraw the circuit for Maverick with this change.

1. Maverick and Goose are flying a long-range stealth mission and they must prioritize power usage to their critical systems. See the circuit below: EF-14 2.4 KV Misc. Systems RMisc 14.2 ΚΩ Critical Systems RCrit 7.8 ΚΩ a) What is the power used by the critical systems? b) What is the efficiency of the power delivered to the critical systems compared to the total power the aircraft is using? c) Efficiency needs to be changed to 100% to complete the mission by changing the value of the Misc. Systems. Redraw the circuit for Maverick with this change.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

(i) A chopper circuit drives an inductive load from 360 DC supply. Given the load resistance as 8 2, the average load current as 20 A and operating frequency is 480 Hz. When the chopper is ON, 7 V is dropped. Calculate (a) conduction period (in milliseconds) (b) blocking period of the chopper (in milliseconds) (c) duty cycle of the chopper (d) draw the ON and OFF time period waveform (ii) Draw the circuit diagram of the single phase bridge rectifier which is used in two quadrant operation (RL load) and explain its operation. · Duty Cycle ON period OFF period
a- Explain why the start-up time of a power plant is important in power system operation. b- Explain why the power system needs for a generation mix. c- Explain why three-phase circuits are preferable than that of single-phase. d- Explain the benefits of free space is being permeable to magnetic field and nonconducting to electric current.
The single - phase ac voltage controller with inductive load. Plot the waveform of output voltage and voltage in each thyristor if the B = 10 %3D degree and delay angle (alpha) in both thyristor is 1- (30 degrees) 2- (90 degrees) 3- (120 degrees)
for Electromechanical Energy Conversion lesson
Topic Draw the equivalent circuits of Class E chopper for the different quadrant operation and write its description.
A dc shunt moton runs at looo Y.P.m From 500V SUPPIY when taking an armatuie currant of 95 A . caleulat e the spees at which itwill Ynn ffom 9250v supPly when taking an armature eurrent of 50A. the resis tance of the armature circuit o. .ssume the flud Per Pole at 250V to have decreased to 70%% of its Value qt 500 V ·
What is meant by FACTS in power systems? Discuss about STATCOM type FACTS device.
Discuss the importance of power delivery and voltage regulation on a motherboard. How do voltage regulators and capacitors contribute to stable system operation?
Q9) A single-phase 230V, 1kW heater is connected across l-phase 230V, 50Hz supply through an SCR. For firing angle delays of 45° and 90°, the power absorbed in the heater element are === and ()a. 453W, 230W b. 754.6 W, 230W c. 220 W, 500.65W d. 454.57W, 250W
5- Calculate the reactance voltage for a machine which runs at 900rpm number of commutator segments is 65, brush width is 1.74 (in commutator segments), coefficient of self induction is 153µH. Assume linear commutation and neglect mica thickness and the conductor current is 27A.
(a) Draw and explain a typical power curve for a wind turbine and write the definition of the four important terms that are shown in the power curve. [ (b) Explain any three factors which affect the efficiency of a wind turbine.
What is fusing factor ?