1. A single phase distributor AB has a total impedance of (0-1 + j0-2) ohm. At the far end B, a current of 80 A at 0-8 p.f. lagging and at mid-point Ca current of 100 A at 0-6 p.f. lagging are tapped. If the voltage of the far end is maintained at 200 V, determine : (i) Supply end voltage VA (ii) Phase angle between V and VR A The load power factors are w.r.t. the voltage at the far end. [(i) 227-22 V (ii) 2°31']

1. A single phase distributor AB has a total impedance of (0-1 + j0-2) ohm. At the far end B, a current of 80 A at 0-8 p.f. lagging and at mid-point Ca current of 100 A at 0-6 p.f. lagging are tapped. If the voltage of the far end is maintained at 200 V, determine : (i) Supply end voltage VA (ii) Phase angle between V and VR A The load power factors are w.r.t. the voltage at the far end. [(i) 227-22 V (ii) 2°31']

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A source of AC emf E₁ = 120/300 volts with an impedance of Z₁ = 2/0° ohms is connected in parallel with another AC source of E₂ = 120/-30º volts with an impedance Z₂ = 2/90° ohms. The two AC source are use to supply a load impedance of Z₁ = 10/-53.10 ohms. Calculate the value of the load current IL. O a. 7.62 amperes O b. 4.42 amperes O C. 5.38 amperes O d. 6.48 amperes
A 220 V, 60 Hz voltage is applied across a series circuit figure comprising a coil of resistance R, inductance L, and capacitor C, determine: (a). The impedance of the circuit. (b). The current flowing in the circuit. (c). The voltage developed across the inductor. (d). The voltage dropped across the capacitor. (e). The voltage dropped across the resistor. (f). The phase angle. 220 v 60 Hz R = 25 Q2 C= 100 μF R L V₁ V 70 1 L= 6 mH C Ve
What is the effective value of 200 volts peak-to-peak? A. 70.7 V. B. 141.4 V. C. 14.14 V. D. 707.0 V.
Answer it with complete explanation.....
Design a CT-FWR to supply a load of (502) with a waveform of the following specifications: - • Vdc = 12 V • Ripple factor = 0.1 % • the main power supply is (220 Vrms, 50 Hz). Determine the following values: - 1- The value of capacitor filter. 2- The maximum load voltage (VmR) 3- The transformer turns ratio (a). 4- The RMS value of the load voltage. 5- Draw the output waveform. (assume ideal diodes)
J62 Q.3: For the magnetically coupled circuit shown, find the values of coupling coefficient power at 10Q resistance is equal to (40W) if Vs-50Z0°v. (Ans.: 0.279) K J752 "k" when the Vs 52 102 4.6752
In Fixed-bias configuration, the DC voltage across the Source terminal is equal to ____. a.Vgs b.0V c.Vp d.Vds
Q5. Answer the following: Explain the power factor using a voltage and current waveform. How the power factor has the adverse effects on the power system quality. What are triplen harmonics? Why these are significant or what are there consequences on transformer and the machines? Explain the five types of voltage disturbances using waveforms, which affect the power quality in distribution system.
I need the answer quickly
56. A single phase thyristor adjust line spacing converter with a resistive load is shown below: V₂ = V sinest SCR ER R V₂ (B) 1.11 (D) 1.44 If the supply voltage is 230V (rms) at 50 Hz, calculate ripple factor for firing angle a-45" and R - 100 9. (A) I (C) 1.21
Describe real and reactive power regulation
4) A single-phase full-wave AC voltage controller consists of two SCRs connected in invers-parallel. The supply voltage is 220V at 50Hz. The controller is used to control heater element of 2500W in an electric oven. The trigger angle is 30o. i) Draw the circuit diagram ii) sketch compatible waveforms for the supply, load and SCR voltages. iii) calculate the rms value of the load voltage and current. iv) Determine the input power factor of the circuit. v) Calculate the average value of the SCR current.