1. A series circuit contains a resistance of 55.1 ohms and the voltage across through it has equation of e = 230 cos(314t –- 50°) V. Determine the current equation and the power equation and the nstantaneous current and power at t = 2.2ms. Determine also the average power in the circuit.

1. A series circuit contains a resistance of 55.1 ohms and the voltage across through it has equation of e = 230 cos(314t –- 50°) V. Determine the current equation and the power equation and the nstantaneous current and power at t = 2.2ms. Determine also the average power in the circuit.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Related questions

Q: Exercise 2: Resistances connected in Series-Parallel across a Sinusoidal AC Supply Calculate the…

A: In the circuit, pure Resistances connected in Series-Parallel across a Sinusoidal AC Supply We are…

Q: A residential four-wire system supplies power at220 V rms to the following single-phase…

A: (b) For first phase total load are – Since loads are bulb so that total power is real and reactive…

Q: of the series connection of the resistor R0 and the inductance L0 between the terminals a and b.…

A: In this question we will find average power delivered to load..

Q: 2)With reference to the waveform given below formulate the equation for the average value of DC…

Q: a) Replace the resistive load with an inductive-resistive one (R-L load), having R=100 0, L=0.06 H.…

A: Ans a) Before wt =0 current through the inductor is 0. For wt= 0 to π Diode is on state output…

Q: 1. What is the main direct cause of reactive power in AC system? A. Resistance of transmission lines…

Q: What is the main direct cause of reactive power in AC system? A. Resistance of transmission lines B.…

A: The explanation is as follows.

Q: (a) What is the resistance of a 220-V AC short circuit that generates a peak power of 96.8 kW? (b)…

Q: a.e. In the alternating current circuit shown in the figure, the voltmeters and amperemeter are…

Q: In the circuit in the figure, there is a load consisting of the series connection of the resistor R0…

A: Given circuit shown with Voltage source Amplitute =1502 vPhase angle θs=0°Time period T=200π μsR=300…

Q: POWER ANALYSIS IN CIRCUITS find, the complex power absorbed in: a. 1 ohm b. capacitor -j10 ohm…

Q: 2)With reference to the waveform given below formulate the equation for the average value of DC…

A: Given A three phase supply is connected to bridge rectifier V=180 V R=200 ohm

Q: A series RC circuit with R=4k0 and C=0.40µF is connected to an AC voltage source t)=100sin200t.…

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: Two electric devices A and B are connected in parallel, and the rms current in A is 15 amp. If the…

Q: An AC voltage of 230 v is applied to a circuit consisting of a resistance of 10 ohms in series with…

Q: Each phase of a wye-connected load consists of a 50-Ω resistance in parallel with a 100-μF…

A: Given data: The frequency of operation is 60 Hz The value of resistance is: 50 Ω The value of…

Q: power system iii) Sketch the phasor diagram of Q2(b)(i) and Q2(b)(ii) above.

Q: ind the currents and voltages in the circuit shown in figure below 20 ww +

A: The solution can be achieved as follows.

Q: a) An alternating current varying sinusoidally with a frequency of 50HZ has an RMS value of 20A.…

Q: A single phase circuit with a given load 5 ohm resistance and capacitive reactance of 2 ohms as…

Q: Vs 18 V pk RL 220 N (a)

Q: If it is connected in series with a pure resistance R with resistance R, inductance L, the current…

A: (a) Calculate the value of the resistance and the inductive reactance of the circuit. VR=IRR=VRI=30…

Q: Q1. In the circuit shown below, the source is E = 220 and 50 Hz and the load is 5 ohms and the angle…

Q: In Figure 1, the power distribution system operates at 50 Hz, 260 V and is occurs. Find the total…

A: The power distribution system 50 Hz, 260 V and consists of three loads. Find the total real and…

Q: For the circuit shown in Figure,a. Find the Thévenin equivalent circuit for the source.b. Find the…

A: (a) Find the Thevenin impedance for the given circuit.

Q: 9. An impedance draws a current i(t) = 10sin(wt-30°) ampere from a voltage v(t) = 220cos(wt-65°)…

A: In this question, Find the current and voltage in phasor form (peak and rms form) Phasor form is…

Q: the circuit in the figure, there is a load consisting of the series connection of the resistor R0…

A: In this question , we will find load value for maximum power deliver to load and maximum power…

Q: 2. Refer to the Figure 2. a) Determine the total impedance of the circuit in polar form. b)…

A: Given

Q: 2)With reference to the waveform given below formulate the equation for the average value of DC…

A: Given A three phase supply is connected to bridge rectifier V=180 V R=200 ohm

Q: R. Yük

A: a) we need to find our L0 and R0

Q: 2. Refer to the Figure 2. a) Determine the total impedance of the circuit in polar form. b)…

A: In this question, Voltage Vs and current I phasor are given. Find the total impedance Z? We know…

Q: Consider the phasor V=110 e-jx/3 Volts What is its real value in Volts? Provide a numerical answer;…

Q: (a) Considering pure resistance in an ac circuit element, show that the alternating voltage and…

Q: circuit in the figure A) equivalent ohmic, inductive and capacitive resistances B) impedance and…

Q: Q.23: For the circuit shown, find the steady-state current "i" and the total power supplied to the…

Q: As shown in Figure Q1(b), two loads A and B are connected in parallel across a 1.5 kV rms 60-Hz…

A: The solution can be achieved as follows.

Q: Q2. For the circuit shown below, sketch the current waveforms is and io and determine the Average…

Q: There is a load formed by the series connection of the resistor R0 and the inductance L0 between the…

A: In this we will find maximum power deliverd to load and load impedance for this..

Q: For the circuit shown, V1= 120V RMS calculate V2, Vout, IL, PIV, Fout, Draw V2 and Vout 3:1 Vout…

A: We need to analyse the given half wave rectifier .

Q: When it is connected in series with a pure resistor R with resistance r and inductance L, the…

A: Given Pure resistor R is connected in series with resistance r and inductance LSinusoidal voltage…

Q: T2 Vs R Vo AA chopper circuit in the figure, 400 V (rms) Control the power of an ohmic load from a…

A: Explanation: “Since you have posted a question with multiple sub-parts, we will solve the first…

Q: Given: A 8 kV circuit has a load consisting of 640 N of resistance in series with 960 N of inductive…

A: the circuit is shown below, First determine the total load with the capacitor branch. To…

Q: In the circuit in the figure, there is a load consisting of the series connection of the resistor R0…

Q: For the circuit shown below, R = 2 2. L-20 mH, and E= 100V. The ac source is 120 V rms at 60 Hz. (a)…

A: As per Bartleby policy we can answer only 3 subparts at a time. So I am solving first three for you.…

Q: (a) Briefly explain the need for power factor correction (PFC). **Please kindly provide 5 points…

A: (a) 5 need of power factor correction is given below. Improved Voltage : When the system has low…

Q: A series RC circuit with R=4kΩ and C=0.40μF is connected to an AC voltage source v(t)=100sin200t.…

Q: Q2. For the circuit shown below, sketch the current waveforms is and io and determine the Average…

A: According to given circuit diagram: For, positive half cycle: Both the diodes will be in forward…

Q: Q2. A load is supplied by a 230V, 50HZ. The active power P and reactive power Q consumed by the load…

A: In practical scenario the alternating voltage is generated which is of sinusoidal nature and is…

Q: For the circuit shown below, R 2 2, L 20 mH, and E-100V. The ac source is 120 V rms at 60 Hz. (a)…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: Q2. For the circuit of Figure 2: a. Find the current I and the total impedance ZT. b. Find the…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub parts for…

Question

1. A series circuit contains a resistance of 55.1 ohms and the voltage across through it has equation
of e = 230 cos(314t – 50°) V. Determine the current equation and the power equation and the
instantaneous current and power at t = 2.2ms. Determine also the average power in the circuit.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Alternating Current (AC) Series Motor and Universal Motor

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
2. Refer to the Figure 2. a) Determine the total impedance of the circuit in polar form. b) Determine the voltage v(t) and current i(t) sinusoidal forms. Sketch one cycle of the waveforms in the same x-axis. Clearly indicating the peak value and the period of each waveform and the phase difference (in milliseconds) between the two waveforms. c) Determine the values of resistance R and inductance L. d) Determine the phasors V,, VR and Vc. e) Sketch the phasor diagram showing Vs, Vr, Vr, Vc and I.
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
1) Two identical voltage waveforms of difference phase angles are shown in Figure B. Write down the expression of waveforms A and B clearly. HUS Voltage (V) 8 0 K/N B 7: ST ot
Draw the waveform of voltage and current under the following conditions: A current which lags the voltage by 60°. A current which leads the voltage by 60°. A current which is in phase with the voltage
Quistion.4. a) A sinusoidal voltage is applied to the resistive circuit in figure.Q.4. a. Determine the following: i. Ims ii. Iavg iii. Ip iv. Ipp 10V 1.0 ΚΩ Figure.Q.4.a
Q4/ Find the voltage average and the voltage waveform for the output of the circuit shown below. Vi=120v (rms) 2.1kr. V. to
A resistor & a capacitor are connected in series across 230V, ac supply. The current taken by the circuit is 4 A for 50 Hz frequency. The current is reduced to 2 A, when the frequency of supply is decreased to 40 Hz. Determine the value of resistor & the capacitor.
1 Calculate average and RMS value of the voltage waveform given in Figure. 4V %3D t(ms)- 4V
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees
A 25-ohm resistor connected in series with a coil of 50-ohm resistance and 150-mH inductance. What is the power factor of the circuit? The standard frequency is 60 Hz. Show complete solution.
An rms voltage of 22.2 V with a frequencyof 1.00 kHz is applied to a 0.290-mH inductor. (a) What is the rmscurrent in this circuit? (b) By what factor does the current changeif the frequency of the voltage is doubled? (c) Calculate the current for a frequency of 2.00 kHz