1. A dc generator, battery, and laboratory supply are connected to resistive load R in Fig..a. For each, determine the value of RL for maximum power transfer to RL.b. Under maximum power conditions, what are the current level and the power to the load for eachconfiguration?c. What is the efficiency of operation for each supply in part (b)?d. If a load of 1 kM were applied to the laboratory supply, what would the power delivered to the loadbe? Compare your answer to the level of part (b). What is the level of efficiency?e. For each supply, determine the value of R for 75% efficiency Rist0.5 fRi20 n2.5 0R.RLE120 VE-(12V0-40 V(b) Barleryte) Laboratory supplyfa) de generatia

We are authorized to answer three subparts at a time, since you have not mentioned which part you…

1. A dc generator, battery, and laboratory supply are connected to resistive load R in Fig.. a. For each, determine the value of RL for maximum power transfer to RL. b. Under maximum power conditions, what are the current level and the power to the load for each configuration? c. What is the efficiency of operation for each supply in part (b)?

1. A dc generator, battery, and laboratory supply are connected to resistive load R in Fig.. a. For each, determine the value of RL for maximum power transfer to RL. b. Under maximum power conditions, what are the current level and the power to the load for each configuration? c. What is the efficiency of operation for each supply in part (b)?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.31P: Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in...

See similar textbooks

Similar questions

1/ Suppose that there are two types of H.V.T.Ls operating at the same voltage and carrying the same current, but one of them with smooth shapewhile the other with standard shape. Which of them, you will choose? a. choosing the smooth one. b. choosing the standard one. c. choosing the one with hollow construction shape. d. all these answers are wrong. 2/ As the ambient temperature in crease the disruptive critical voltage of coron a is: a. Decreased b. Increased c. No effect d. All these answers are wrong. 3/ Using HV underground cable improvevoltageprofile and power factor in any loaded inductive electrical grid because. a. Due to its inductive power effect. b. Due to resistive Effect. c. Due to its capacitive power effect. d. All of the above answers are wrong.
A 2 wire d.c. ring distributor is fed at A with 220 V. The various loads are 10A at B, 20A at C,30A at D and 10A at E. The resistances of the sections AB, BC, DC, DE and EA are 0.1 £2, 0.05 $2, 0.01 2, 0.025 2 and 0.075 respectively. Determine, a. Point of minimum potential b. Current in each section [Ans.: Point C, 29.04 A, 19.04 A, 0.96 A, 30.96 A and 40.96 A
An AC circuit is shown in the diagram. The source of emf has a peak voltage of 9.00 V and a frequency of 60.0 Hz. Assume the wires contribute a negligible amount to the resistance and the AC source has negligible internal resistance. 524 2 493 2 1.56 k2 a) Find the equivalent resistance of the circuit. Redraw the circuit showing the equivalent resistor and use this simplified circuit for the rest of the problem. 315 2 Re = b) Find the rms current. 9.00 V, 60.0 Hz c) If the current is zero at time t= 0, find the first two times (after time t-0) that the current is equal to its rms value. and d) Find the average power dissipated by the circuit.
N.theory question electrical engineering.
2.7 a) The terminal voltage and terminal current were measured on the device shown. The values of v, and i, are provided in the table. Using these values, create the straight line plot of v, versus i,. Compute the equation of the line and use the equation to construct a circuit model for the device using an ideal voltage source and a resistor. b) Use the model constructed in (a) to predict the power that the device will deliver to a 25 0 resistor. Answer: (a) A 25 V source in series with a 100 N resistor: (b) 1 W. v, (V) , (A) 25 Device 15 0.1 5 0.2 0.25 (a) (b)
A. Discuss the importance of power electronics interfaces in microgrid installations B. With the aid of diagram describe DC microgrid C. With the aid of diagram describe AC microgrid
b. three The allowable ampacity of a 4 AWG THHN conductor is 95 amperes. If we have four 4 AWG THHN conductors, what is the adjusted ampacity? a. 48 b. 63 C. 76 d. 95 o conduct
23.Compare between 1 ph IM and 3 ph IM. 24.Draw the equivalent circuit of 1 ph IM. 25.Write the equations to determine X0 and RO of 1 ph IM. 26. Why the p.f under no load is a very small value.
Two batteries A and B are connected in parallel and load of 10 ohms is connected across their terminals. A has an e.m.f. of 12 V and an internal resistance of 2 ohms ; B has an e.m.f. of 8 V and an internal resistance of 1 ohm. Use Kirchhoff’s laws to determine the values and directions of the currents flowing in each of the batteries and in the external resistance. Also determine the potential difference across the external resistance. *
12. Find the resistance of a piece of 12 AWG aluminum wire that is 550 ft long. Assume a temperature of 20°C. - a. 0.876 b. 0.293 c. 1.432 d. 15.023 1
Questions Q1) what is meant by Insolation, ARC in solar systems? Q2) mention the types of solar systems? Q3) explain with drawing the main components of solar system. Q4) explain with equations the intuitive technique for design pv/battery system. Q5) Discuss all the results in Tables (1 to 3). Q6) Referring to Tables (4) & (5); draw & discuss the relations: 1. (I VS THD of current), 2. (V Vs Q).
The ratio of the . between the ends of the wire to its . . is .22 ............ * .constant Power, Current P.D, power O power, P.D Current, resistance O P.D, current O