Q2: The daily demands of three consumers are given below. Plot the load curve and find (i) maximum demand of individual consumer (ii) load factor of individual consumer (iii) diversity factor and (iv) load factor of the station. (v) daily requirement if the calorific value of oil used were (9,000 kcal/kg) and the average heat rate of station were (2680 kcal/kWh). Time 6АМ -1 РМ 5 PM-9 РМ 12AM-6AM 80 W ПРM-5 РМ 9 РМ-12 АМ Consumer 1 400 W 1500 W 600 W No-load Consumer 2 No-load 350 W 800 W 1000 W 300 W Consumer 3 50 W 110 W 1100 W 900 W 150 W

Q2: The daily demands of three consumers are given below. Plot the load curve and find (i) maximum demand of individual consumer (ii) load factor of individual consumer (iii) diversity factor and (iv) load factor of the station. (v) daily requirement if the calorific value of oil used were (9,000 kcal/kg) and the average heat rate of station were (2680 kcal/kWh). Time 6АМ -1 РМ 5 PM-9 РМ 12AM-6AM 80 W ПРM-5 РМ 9 РМ-12 АМ Consumer 1 400 W 1500 W 600 W No-load Consumer 2 No-load 350 W 800 W 1000 W 300 W Consumer 3 50 W 110 W 1100 W 900 W 150 W

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Similar questions

Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in Figure 2.27. (a) Obtain expressions for P12 and Q12. (b) Determine the maximum power transfer and the condition for it to
What is the purpose of power factor correction to a given load? O To reduce the amount of voltage to the load. O To reduce the amount of dependence on automated machinery. O To reduce the amount of current to the load. O To reduce the amount of resistance of the load.
A 500 MVA synchronous machine has H, = 5.6 MJ/MVA and a 1200 MVA machine has H₂ = 2.0 MJ/MVA. The two machines operate in parallel in a power station. What is the equivalent. H constant for the two, relative to a 100 MVA base?
A generator operating at 50 Hz delivers 1 p.u. power to an infinite bus through a transmission circuit in which resistance is ignored. A fault takes place reducing the maximum power transferable to 0.5 p.u. Where as before the fault, this power was 2.5 p.u. and after the clearance of the fault, it is 2 p.u. The value of 8 is max
A power station is to supply four regions of loads whose peak values are 10,000 kW, 5000 kW, 8000 kW and 7000 kW. The diversity factor of the load at the station is 1.5 and the average annual load factor is 60%. Calculate the maximum demand on the station and annual energy supplied from the station.
A power station is to supply two loads. The daily load curve of the station is as shown in figure below. If the load factor of the two loads are 0.416 and 0.458 respectively, and the diversity factor of the power station is 1.142, find:1- The load factor of power station.2- The energy consumed per day and the maximum demand(connected load) of each load.
(b) An inductive load consisting of resistor, R and inductor, L in series feeding from a 240430° Vrms, 50 Hz supply consumes 6 kW at lagging power factor of 0.88. (i) Determine the current through the load. (ii) Find R and L. (iii) Draw the phasor diagram of supply voltage and current.
step down chopper has Vs = 230 V and R = 10 0. For a duty cycle of 0.4, the power taken by the chopper is 2097 Watts. Find the chopper efficiency. Take the voltage drop across the chopper switch as 2 V. a) 98 % b) 89.96 % c) 99.14 % d) 96.54 %
A base load station having a capacity of 18 MW and a standby station having a capacity of 22 MW share a common load. Find the annual load factors and plant capacity factors of two power stations from the following data :Annual standby station output = 740OMWH Annual base load station output = 100000 M kWh Peak load on standby station = 12 MW Hours of use by standby station/year = 2200 hours
Problem 4 An electric saw, a wood shaper, and a motor load of a workshop establish a 18 kVA power demand at 0.5 power factor lagging on a 208 V, 60 Hz supply. a) Establish the power triangle for the load. b) Determine the power-factor capacitor that must be place in parallel with the load to raise the power factor to 0.9 lagging. c) Determine the change in supply current from the uncompensated to the compensated system. d) Determine the power-factor capacitor that must be placed in parallel with the load to raise the power factor to unity.
Table Q2a Time (hours) 0-6 6-12 12-14 14-18 18-24 Load (MW) 45 90 135 150 75 Referring to the Table Q2a; i) Draw the load curve and the load duration curve [Use the graph paper provided] ii) Indicate the base load and the peak load on the graph. Determine the values for both loads. iii) Choose the suitable generating units to supply the load and list their operating schedules. Later, compute the total installed capacity. iv) Calculate the load factor and the plant capacity factor. Discuss the impact on the operating schedule if the plant capacity factor increases to 0.9.
7. A power station has to meet the following load demand : 50 kW Load A between 10 A.M. and 6 P.M. Load B 30 kW between 6 P.M. and 10 P.M. Load C 20 kW between 4 P.M. and 10 A.M. Plot the daily load curve and determine (f) diversity factor () units generated per day (üi) load factor. () 1-43 () 880 kWh (i) 52-38%]