1) Design a network to maintain a continuous 15 V DC voltage to a machinary having a load impedance of RL = 1,5 kN. In order to realize this request, a transformer having a primer voltage 220 V AC and a seconder voltage 30 V AC (220/30 V AC transformer), some silicon diodes, zener diode and some resistors of 200 Q can be considered in design. a) Draw the overall network, explain the tasks of each component and overall operation of the network in your design. b) Calculate load current (IL). c) Calculate power dissipated by zener diode (if used in design)

1) Design a network to maintain a continuous 15 V DC voltage to a machinary having a load impedance of RL = 1,5 kN. In order to realize this request, a transformer having a primer voltage 220 V AC and a seconder voltage 30 V AC (220/30 V AC transformer), some silicon diodes, zener diode and some resistors of 200 Q can be considered in design. a) Draw the overall network, explain the tasks of each component and overall operation of the network in your design. b) Calculate load current (IL). c) Calculate power dissipated by zener diode (if used in design)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

use the kvl and draw its schematic diagram
solve a and b
Determine the forward voltage and forward current of a diode in a circuit. The circuit is composed of a dc voltage source with its positive terminal of 10V connected in series to a 1Kohms resistor and the anode of a diode. The cathode of the diode is connected to ground. Use ideal device model approach. Draw the circuit and show your solution/s.
60 V D1 D2 2 kohm DA D3 -60 V Assume that an input signal is applied to the circuit given above, as shown in the figure next to it. Accordingly, answer the following questions. The diodes used are silicon diodes, their operating voltages are 0.7 volts, and can be omitted because their resistance is very small. Calculate V p-out( Vm ) for this circuit.
for The Gircuit shown in figure if (B =50) tind The values of CIe). and of Then express The change in value by apercentage + 15U RB, = 100Ka R82 = 50 KQ RE 3K2 %3D
Assuming the practical model, what PIV rating is required for the diode? The transformer is specified to have a 12 Vrms secondary voltage for the standard 110 V across the primary. (2nd Approximation) * D 110 V D 10 kn- Mout) alll
Trial example of how to use Kirchhoff analysis to determine the initial current in each section along with its direction and the potential difference across the load
5
Find the equivelent resistance of the circuit below. (Rin)Conduction diodes' resistance is 0Insulating diodes' resistance is infinite.R1 = 10 ohm
(b) If such a circuit is to be used to supply an average of 10 V across the load, calculate the turns ratio of the transformer required. The input mains voltage is 240 V rms at 50 Hz. You may assume ideal diodes in your analysis. Note again that there is to be no smoothing of the load voltage.
A single phase bridge type full wave uncontrolled rectifier is connected to a voltage source and has an RL load at its output. The RL load satisfies the (L / R) >> T condition. In this case, the output current of the rectifier is 10 A pure direct current. Voltage source impedance consists of inductance only and its value is 3 mH. The function of the voltage source Vs (t) below Re given. V,) = 311sin(2750r)V| Note: T= 0.02s is the period value of the voltage source. R and L values do not matter in solving the problem. A; What is the value of the overlap angle in radians? B; Find the effective value of the output voltage
Discussion: 1. Discuss the obtained curves. 2. What are the advantages of using cascade voltage regulater circuit? 3. To stabilize a voltage of 65 V, one can: a. Use one 65V zener diode b. Use ten 6.5 V zener diodes in series If the costs are irrelevant, then which solution is best and why? I R. (A I O Vin v)Vout Figure (5.2) A stabilizer circuit with variable power supply. IL V (V) Vout RL Figure (5.3) A stabilizer çircuit with variable load.