1) Design a network to maintain a continuous 15 V DC voltage to a machinary having a load impedance of R1 = 1,5 kN. In order to realize this request, a transformer having a primer voltage 220 V AC and a seconder voltage 30 V AC (220/30 V AC transformer), some silicon diodes, zener diode and some resistors of 200 Q can be considered in design. a) Draw the overall network, explain the tasks of each component and overall operation of the network in your design. b) Calculate load current (IL). c) Calculate power dissipated by zener diode (if used in design)

1) Design a network to maintain a continuous 15 V DC voltage to a machinary having a load impedance of R1 = 1,5 kN. In order to realize this request, a transformer having a primer voltage 220 V AC and a seconder voltage 30 V AC (220/30 V AC transformer), some silicon diodes, zener diode and some resistors of 200 Q can be considered in design. a) Draw the overall network, explain the tasks of each component and overall operation of the network in your design. b) Calculate load current (IL). c) Calculate power dissipated by zener diode (if used in design)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q-2 A Cockcroft-Walton type voltage multiplier has Seven stages with capacitances, all equal to 0.3 µF. The supply transformer secondary voltage is 150 kV at a frequency of 100 Hz. If the load current to be supplied is 3 mA, find (a) the percentage ripple, (b) the regulation, and (c) the optimum number of stages for minimum regulation or voltage drop (d) the maximum output voltage.
Explain five (5) applications of the hall effects With the aid of a diagram, explain how a P-N Junction is form. iii. State five (5) application of PN Junction, and explain the property of the PN junction that make those application possible. Explain what carrier mobility is and elaborate on the factors that influence carrier mobility. A 80 V rms is stepped down to 18V rms by a transformer. The output from the transformer is rectified using a half wave rectifier circuit and connected to a 47.5 Ω load resistor. Draw a circuit diagram of this arrangement and the waveform at each stage. Calculate the following about the circuit in Figure 2.1 (If silicon diodes are employed in the rectification); the peak value of the output voltage considering the drop across each diode, the average voltage, iii. The current through the load resistor, The current diode, The frequency of the output signal, Calculate the efficiency of the full wave rectifier expressed in percentage. vii. Sketch…
Explain five (5) applications of the hall effects With the aid of a diagram, explain how a P-N Junction is form. State five (5) application of PN Junction, and explain the property of the PN junction that make those application possible. Explain what carrier mobility is and elaborate on the factors that influence carrier mobility. A 80 V rms is stepped down to 18V rms by a transformer. The output from the transformer is a. rectified using a half wave rectifier circuit and connected to a 47.5 Q load resistor. Draw a circuit diagram of this arrangement and the waveform at each stage.
4. For the circuit shown in the figure below uses a transformer of 230V/12V-0-12V and all diodes are Ge find the following, RL-3.3k2. The name of the circuit is ........ Current through the load is............The DC output voltage is............ Draw the input & output wave forms ✈ ellel eetee CT D₂ DE www R₂
Design a DC power supply using FWR to perform the following requirements. Find V_dc, V_rms, V-ripple, PIV of the diode. draw the waveform of (V_in, V_out, L_in, I_load, V_diode and I_diode). Input voltage = 25 Transformer turn ratio 0.1 load resistance = 1k ohm Ripple factor = 0.025 Diode type =Si
1 Design a full-wave regulated power supply using 5:1 center-tapped transformer and an 8-V, 2- W zener diode that will provide a constant 8-V to a load varying from 100 ohms to 500 ohms. The input voltage to the transformer is 110 V, 50 Hz.
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) IN4001 Ry OV 10k) D IN4001
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D1 IN4001 R. V out OV 10 kN D2 IN4001 llle
QUESTION 3 is dc -Lac 0 f(t) = Ide T If ripple-free load current in steady-state is assumed, the input current is waveform of the single-phase full-wave rectifier may then be depicted as shown in the figure above for an ideal input transformer. With the assumption that the supply is ideal and perfectly smooth and ripple free load current, which implies an infinitely large load inductance, it is quite straightforward to obtain an analytical expression for the input current harmonics. The rectangular wave is defined as de 270 when 0< t < π when_π
(b) A three-phase uncontrolled bridge rectifier is connected to an AC supply of 415V through a delta-star transformer as shown in the Figure. The load consists of large inductance to render a level load current of 60A at 300V. Assuming voltage drop across the power device to be 0.7V, compute the following: i) Rms value of secondary phase voltage and current; ii) Rms value of primary phase voltage and current3; iii) Transformer power rating in kVA and transformation ratio; iv) Device ratings. 本の。本の本の Load 本の。本。本の。 Figure
1) a) As depicted in the figure, input voltage is 120 Volts (RMS) and diode drops are 0.7 Volts. Design this circuit with given two ac outputs and calculate turns ratio of live transformer. voltage i) 10 V ii) 100 V 2) b) Consider a circuit using Si diodes and 10 k ohms resistors. Design this clipper circuit with output ranges below; i) -0.7 V and above ii) +2.1 V and above iii) +1.4 V c) As given in the figure a clamper circuit with the input +10V- signal Vi is proposed to design. Determine the output voltage with the exact solution step by step. Sketch transfer characteristic Vo versus V₁. V₂ Vo H 2RS -10V- -2√ 01 Vo Trims
Question-4: In the bridge type circuit shown below, the diodes are assumed to be ideal. The transformer is specified to have a 15 Vrms secondary voltage. Find: A- D.C. output voltage Vp(out). B- Peak inverse voltage PIV. 1:4 +100 V D. D V. ov -100 V Vp(out) D 10 kf) elle