1-A thin aluminum plate profile shown in the accompanying figure is subjected to an axial load. deflection and the average normal stresses along the plate using the model shown in the figure. The plate has a thickness of 0.5 cm and a modulus of /|| ||| Approximate the 2 cm 2 cm elasticity E=70 GPa 10 cm 2 cm 2 cm

1-A thin aluminum plate profile shown in the accompanying figure is subjected to an axial load. deflection and the average normal stresses along the plate using the model shown in the figure. The plate has a thickness of 0.5 cm and a modulus of /|| ||| Approximate the 2 cm 2 cm elasticity E=70 GPa 10 cm 2 cm 2 cm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.11P: The polyethylene liner of a settling pond is subjected to stresses ax= 350 psi. a = 112 psi. and =...

See similar textbooks

Related questions

Q: The figure below are timber planks joined together by a bolt with the corresponding measurements.…

A: Given data: τw=10 ksiσb=20 ksid=34 in Need to determine the maximum safest value of P.

Q: 9. A rod has three segments as shown in the figure. The position of applied loads and diameter of…

Q: The plate of the figure is subjected to a bending moment with irregular cycles, which are repeated.…

A: NOTCH SENSITIVITY FACTOR(q) It is defined as the susceptibility of a material to succumb to the…

Q: The system in the figure consists of AB with a wall thickness of 5 mm and an outer diameter of dAB =…

Q: For the figure below, Determine the following: 10 MPa 40 MPа 50 МPа The oavg is equal to in MPa: The…

Q: ... - 24 in.-20 in.→ 20 in. 16 in. 8 in.I 8 in. The above figure is a section of a column. If the…

Q: In figure below, the shear force (Q) is equal to 150 kN. What is the shear stress (t) at the neutral…

Q: For the figure shown, have the following information: Bar (1) made of bronze Bar (2) made of…

Q: 1. Question: With a pin on the AB beam A and a short lever BC as shown in the figure is supported.…

A: Given dataDiameter of the pins ar A,B and C d = 18mmLoad P = 30kNAngle α= 600Pin =ADetermine the…

Q: Two steel wires support a moveable overheadcamera weighing W = 28 lb (see fgure part a) usedfor…

A: W=28lb α = 22° β = 40°diameter1=30milsdiameter2=35mils1mil=0.001in To-Find:- a) Tensile stresses σ1…

Q: Determine the number of life cycles for an alternating stress of 70 ksi. Select one: a. N = 1.66E+05…

Q: Determine the nodal displacements and the element stresses, including principle stresses, due to the…

Q: Consider the circular bent rod with điameter 20 mm. The free-end of the bend is subjected to loads…

A: The horizontal force of 400 Newton will generate a bending moment at the section b-b. The vertical…

Q: 1-A solid axial member which is made from three parts with different materials (sections 1 and 3) is…

A: I have used the first row for the values of youngs modulus. NOTE: According to Bartleyby's policy we…

Q: 2.84 The rigid bar of negligible weight is supported as shown in the figure. If W = 80 kN, compute…

Q: 4. A central horizontal section of a hook is symmetrical trapezium 90 mm deep. The inner width being…

A: Note:As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: 1.6-7/ A wire of length L 4 ft and diameter d-0.125 in. is stretched by tensile forces P = 600 lb.…

Q: Problem 5: (D2) You are an engineering intern at a manufacturer of mechanical tools, your senior…

Q: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure.…

A: Consider the Free Body Diagram: Force acting on Bronze rod:FCD=2PStress in Bronze…

Q: The components of plane stresses at a critical point are shown in the following figure. Determine…

Q: The stress concentration occurs whenever there is an abrupt change in the cross-section of a…

A: Stress concentration Factor (k) : it is defined as the localisation of higher stresses due to…

Q: 3. PROBLEM In the Figure shown, determine the deformation At B and C as required by a load P = 20…

A: To find : find the deformation of at B and C . Given : load P=20 kN E=70 GPa area A=900mm2 lenght…

Q: A steel cylinder is 160 mm ID and 320 mm OD. If it is subject to an internal pressure of 150 MPa,…

A: Given data Internal diameter of steel cylinder (Di) = 160 mm internal radius (ri) = 80 mm outer…

Q: P1.8 (WP Determine the normal stress in rod (1) for the mechanism shown in Figure P1.8. The diameter…

Q: Bronze A = 300mm² E = 83 GPa 2.00 m %3D Steel A = 600mm? E = 200 GPa 1.00 m A 0.60m 1.00 m 1.00m

Q: - A member ABCD is subjected to point loads Pi and Pa with magnitudes of 5 kN and 12 kN respectively…

A: There are three members connected in series. Since the both ends are subjected to forces of…

Q: A steel bolt of 6 mm in diameter has a tensile load of 40 kN. Find the average tensile stress at the…

Q: Problem C-2 [Average Normal and Average Shear Stresses] A structure is under an external loading of…

A: To normal and average stress at section aa

Q: 28. A prismatic bar PQRST is subjected to axial loads as shown in the figure. The segments having…

Q: A thin steel plate with the profile shown in the accompanying figure is subjected to an axial load.…

Q: C. For the figure shown below, if the stress in steel and bronze are not exceeding 150MPA and 70MPA…

Q: 2. In the stress-strain curve for steel shown below, identify following stresses in ksi and write…

A: Yeild point - Yeild point is the point at which the material will have an appreciable elongation…

Q: A thin aluminumplate profile shown in the accompanying figure is subjected to an axial load.…

A: Draw a diagram diving the given plate into different areas and also draw the equivalent stiffness…

Q: Determine the normal stress in bar (1) for the mechanism shown in Figure P1.9. The area of bar (1)…

A: GIVEN: WC=12 kN/mWD=30 kN/m Area of bar is 2,600 mm2 a = 7.5 m and b = 3.0 m TO FIND: Determine the…

Q: P1.30 Rigid bar ABC shown in Figure Pl.30 is supported by a pin at bracket A and by tie rod (1). Tie…

A: From trigonometry -

Q: Q1/ (A) - The mechanism of femur bone is approximated as a circular tube (3 cm and 2 cm are the…

Q: For the structure shown: P= 600 lb, a = 4 in, b 5 in, c = 7 in, L, = 8 in, L, = 9 in. The part ABCD…

A: Given data as per question Force = 600 lb Area of aluminium rod =2.8 in2 E of aluminium rod…

Q: 1.5-2 A bar of length 2.0 m is made of a structural steel having the stress-strain diagram shown in…

A: Length of bar L=2 m σy=250 MpaE=200 Gpaelongation when axial load is applied ∂l=6.5 mm

Q: The connecting rod number 2 shown in the figure is made of low carbon steel with yield strength Sy =…

A: (a) To find: The force on the tie rod, the mean and amplitude stresses on the connecting rod…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure.…

Q: Figure Q1(b) shows three rods that were assembled together and held between rigid supports. The…

Q: 1.7C1 A. 1.4C1 B CI 0.9C1 Uniform plastic elongation Necking 4Riastic 4% 15% 35% Strain in %…

Q: A steel bolt of 6 mm in diameter has a tensile load of 40 kN. Find the average tensile stress at the…

A: Step by step solution is given below

Q: The state of stress acting at a critical point on a wrench is shown in the figure. Determine the…

A: Given: The state of stress is given as Here, σx=300 MPaτxy=150 MPa

Q: Q1: A circular steel rod ABCD is loaded as shown below. Use the following data to Find the maximum…

A: The load in the bar CD is The load in the bar BC is The load in the bar AB is

Q: GPa, G = 83 GPa), the state of the stress is illustrated in the figure below. For the given plane…

Q: Question 4 The bar in Figure is made of steel that is assumed to be elastic perfectly plastic, with…

Q: Compare the torsional rigidities of the following sections: (a) a hollow tube 30 mm outside…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: As shown in the figure, a column has a 10-inch by 10-inch cross section. A compressive load P with…

Concept explainers

Thermodynamic Relations

Thermodynamics is the division of physics that deals with the transfer of any kind of energy, whether it be heat, temperature, or work, from one object to another.

Question

It will be solved by the INTRODUCTION TO FINITE ELEMENT METHOD.

Transcribed Image Text:1-A thin aluminum plate profile shown in the accompanying figure is subjected to an axial load. deflection and the average normal stresses along the plate using the model shown in the figure. The plate has a thickness of 0.5 cm and a modulus of Approximate the 2 cm 2 cm elasticity E=70 GPa 2 cm 2 сm 3000 N б ст 6 cm 10 cm 2 cm 2 cm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Trending now

This is a popular solution!

Step by step

Solved in 7 steps with 41 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clement
The stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
An element in plane stress on the fuselage of an airplane (figure part a) is subjected to compressive stresses with a magnitude of 42 MPa in the horizontal direction and tensile stresses with a magnitude of 9.5 MPa in the vertical direction (sec figure part b). Also, shear stresses with a magnitude of 15.5 MPa act in the directions shown. Determine the stresses acting on an element oriented at a clockwise angle of 40g from the horizontal. Show these stresses on a sketch of an element oriented at this angle.
The strength-to-weight ratio of a structural material is defined as its load-carrying capacity divided by its weight. For materials in tension, use a characteristic tensile stress obtained from a stress-strain curve as a measure of strength. For instance, either the yield stress or the ultimate stress could be used, depending upon the particular application. Thus, the strength-to-weight ratio RS/Wfor a material in tension is defined as Rs/w= in which a is the characteristic stress and 7 is the weight density. Note that the ratio has units of length. Using the ultimate stress Uas the strength parameter, calculate the strength-to-weight ratio (in units of meters) for each of the following materials: aluminum alloy 606I-T6, Douglas fir (in bending}, nylon. structural steel ASTM-A57.2, and a titanium alloy. Obtain the material properties from Tables [-1 and 1-3 of Appendix I. When a range of values is given in a table, use the average value.
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
Two steel wines support a moveable overhead camera weighing W = 28 lb (see figure part a) used For close-up to viewing of field action at sporting, events. At some instant, wire I is at an angle a = 22° to the horizontal and wire 2 is at angle fi = 40°. Wires I and 2 have diameters of 30and 35 mils, respectively. (Wire diameters are often expressed in mils; one mil equals 0.001 in.) (a) Determine the tensile stresses s and s2 in the two wires. (b) If the stresses in wires 1 and 2 must be the same, what is the required diameter of wire 1 ? (c) To stabilize the camera for windy outdoor conditions, a third wire is added (see figure part b). Assume the three wires meet at a common point coordinates (0, 0. 0) above the camera at the instant shown in figure part b. Wire I is attached to a support at coordinates (75 ft, 48 ft, 70 Ft). Wire 2 is supported at (-70 ft. 55 ft, 80 Ft). Wire 3 is supported at (-10 ft. -85 Ft, 75 ft). Assume that all three wires have a diameter of 30 mils. Find the tensile stresses in all three wires