.A steel plate is exposed to solar heat flux of 800 W/m² on one side. The plate is exposed to air at 30°C on both sides. The convection coefficients are 10 W/m²K on the back side and 15 W/m²K on the front. Determine the equilibrium temperature. Neglect radiation loss

.A steel plate is exposed to solar heat flux of 800 W/m² on one side. The plate is exposed to air at 30°C on both sides. The convection coefficients are 10 W/m²K on the back side and 15 W/m²K on the front. Determine the equilibrium temperature. Neglect radiation loss

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.60P: 1.60 Two electric resistance heaters with a 20 cm length and a 2 cm diameter are inserted into a...

See similar textbooks

Related questions

Q: A 1500 kW electrical heater is used to heat 20 kg of water (cp=4186 J/kgK) lin an insulated bucket, ...

Q: uppose two infinitely long flat plates, separated by 3 in. distance and 0.5 in. thickness, conducts ...

A: Givend=3in.t=0.5inV=5m/sμ=1Pa-sS.G=0.89

Q: Q3/ The overhang beam is subjected to the uniform distributed load having an intensity of w = 40 kN....

Q: 8 F-5 Fighter airplane has q caing area of 170 ft?. The wing gener ateo a lift of 18000 16. For 9 Bl...

Q: Consider a turbine consisting of two stages. The overall pressure ratio is four and the inlet condit...

A: Calculate the pressure ratio for each stage. rp=rp,overall=4=2 Calculate the temperature after first...

Q: 5.Some oil is full of the space by two parallel plates. The lower plate is stationary, while the upp...

A: The dynamic viscosity of oil is 1.3625 kg/m-s.

Q: is |Q|=-kA(dt/dx) the law that defines the rate of heat transfer by conduction (fourier's law of hea...

A: Q=-kAdt/dx is the Fourier's law of heat conduction which defines the rate of heat transfer by conduc...

Q: width of the blades at the exit is 1 cm. Calculate the following: (a) power required to drive the co...

Q: 3. Find the total moment about point 0, given: Q=44 N, T=27 N, P=60 N. Find the vertical force R act...

Q: Problem 1. Beam AB has the given loading per unit length, q(x), Young's modulus, E, and a rectangula...

Q: Determine the change in entropy for the water?

A: Determine the change in entropy.

Q: Moment of Inertia rmine the second mor (a) x-axis (b) y-axis

Q: 11.10 The acceleration of a particle is directly proportional to the square of the time t. When 1 = ...

Q: A weight of 200lbs. rests on an inclined plane that makes an angle of 35° with the horizontal. If th...

Q: ow that the index 'n' of polytropic expansion in a turbine of infinitesim stage efficiency np is giv...

Q: A ball is kicked horizontally outward with a velocity of VA from point A and just clear the tree at ...

A: Here let a=10 AB distance=6.5+0.1 x 4AB=7.5mFrom A to Bh=1.5ma=g=9.81 m/s2h=ut+12at21.5=0+12 x 9.81 ...

Q: A rigid closed tank contains refrigerant 134a wnich is initially a two-phase liquid - vapor muture w...

Q: Determine the ratios of the weights of four beams that have same length.are made of the same materia...

A: The shapes given in the question are Rectangle Square Circle Pipe The height and width of rectangle ...

Q: 1- compressor with compression ratio (7:1). The pressure, temperature and volume at the beginning of...

Q: A hot steam pipe having an inside surface temperature of 250°C has an inside diameter of 8 cm and a ...

A: The thermal resistance of a hollow pipe can be calculated using the formula given below as- R=12πkLl...

Q: The specific gravity of mercury relative to water is 13.55. What is most nearly the specific weight ...

A: Specific gravity of Mercury, SGHg=13.55The specific weight of water, γw=62.4 lbf/ft3

Q: Diameter = 100m Bench Height = 10m Bench Width = 5m Bench Slope Angle = 45° a. What is the volumetri...

A: Write the given data. V1=63846.66 m3V1+V2+V3=99745 m3

Q: A medium size power station is used to produce 30 MW net power for a refinery. The station uses stea...

Q: Steam generators are a type of heat exchanges that are used in power plants to generate steam at des...

A: Answer: (i) The steam mass flow rate is 11.9522 kg/sec. (ii) The inlet velocity of the steam is 4.24...

Q: The following data are obtained from a tensile test of a copper specimen. - The load at the yield po...

A: It is required to determine final area of specimen

Q: The Rankine cycle with one closed feedwater heater (CFWH). Superheated water vapor enters the turbin...

Q: A cylindrical propane tank has an outside diameter of 3.25 m. If the allowable hoop stress is 100 MP...

Q: A steel rod having a cross-sectional area of 300 mm and a length of 150 m is suspended vertically fr...

Q: A person is pushing on a uniform block of wood as shown in the figure and parameter table. The block...

Q: b) Steam generators are a type of heat exchanges that are used in power plants to generate steam at ...

A: Answer: (i) The steam mass flow rate is 11.9522 kg/sec. (ii) The inlet velocity of the steam is 4.24...

Q: A solid shaft is to transmits 22 kW at 110 rpm. Determine the diameter of the shaft if the shearing ...

A: Given data as per question Power transmitted =22kw Speed =110 rpm hearing stress =35 Mpa The angle o...

Q: The velocity-time graph of a particle in one dimension is shown in the figure below. 4 3 2 6. 8. 10 ...

A: As per the company policy, we are restricted to solve first three part of question. Please ask other...

Q: A nozzle is a device that is used to increase the velocity of a fluid by varying the cross-sectional...

A: Given:Pressure, P=500 kPaTemperature, T=600Kmass flow rate, m˙=50 kg/sInlet cross sectional area=5 m...

Q: Determine optimum velocity

A: Given data: For single stage impulse turbine:Rotor diameter,d=1 mSpeed,N=2500 rpmNozzle angle,θ=200...

Q: Oxygen gas initially at 355 K and 1.50 bar undergoes the following cyclic ...

Q: The truss is designed in such a way that all compression and tension members have an area of 300 mm2...

Q: with water (the shaded part), with 0% of the volume in the cylinder is filled pressure of p = Po. Th...

A: data given that cylindrical container cross section radius = R axial length =waccelerating in x1 di...

Q: ascending the 30° incline with an acceleration of 5 m/s?. At what angle must the post be inclined in...

A: TO FIND ANGLE

Q: Given: A ground steel rod with known diameter d is operating at temperature T. You are designing und...

Q: How does vortex tube refrigirator work in a portable min coolerbox or portable refridge? kindly expl...

A: Vortex tube refrigerator is used compressed air to cool as low as to air-condition the space. this s...

Q: 2. A medium size power station is used to produce 30 MW net power for a refinery. The station uses s...

Q: Cheezy placed an order for 16 cubic meters of sand. The sand was ejected from a dump truck at a 50-d...

A: Given Velocity = 2 ft/s Angle 50 To find Radius of curvature

Q: Given: A part is made of ductile material and subjected to principal stresses 01, 02,03. statically ...

A: For solution refer below images.

Q: A ball is kicked horizontally outward with a velocity of VA from point A and ust clear the tree at p...

Q: An U-shaped tube consist of liquid and liquid oscilloctes Enside the tube, find the equafion of moti...

Q: e output voltage of

A: Need to find Output voltages.

Q: he hydroelectric facility that has been proposed will consist of a turbine with an efficiency of 89....

A: Given:Efficicnecy of turbine=η=89.2%=0.892vertical depth of 14.8 m below the riverbedHydraulic diame...

Q: Consider the air flow over the wing of a civil airliner flying at M. 0.85 and at an altitude of 10,0...

A: When the change in flow variables is minor and gradual, isentropic flows occur. Sound wave creation ...

Q: A nozzle is a device that is used to increase the velocity of a fluid by varying the cross-sectional...

A: By steadly flow energy equation : h1+ V^2 /2 +g Z1+q = h2 + v^2/2+gZ2 +W Nozzle is given :- W= 0 ( n...

Q: A blanking operation is to be performed on 2.0 mm thick cold-rolled steel (half hard). The part is ...

A: Write the given data. t=2 mmD=45 mmA=0.075

Question

4.A steel plate is exposed to solar heat flux of 800 W/m² on one side. The plate is exposed to air at 30°C on both sides. The convection coefficients are 10 W/m²K on the back side and 15 W/m²K on the front. Determine the equilibrium temperature. Neglect radiation loss

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1.60 Two electric resistance heaters with a 20 cm length and a 2 cm diameter are inserted into a well-insulated 40-L tank of water that is initially at 300 K. If each heater dissipates 500 W, what is the time required for bringing the water temperature in the tank to 340 K? State your assumption for your analysis.
2.34 Show that the temperature distribution in a sphere of radius . made of a homogeneous material in which energy is released at a uniform rate per unit volume , is
A solar radiant heat flux of 700 W/m2 is absorbed in a metal plate that is perfectly insulated on the back side. The convection heat- transfer coefficient on the plate is 11 W/m2 • C, and the ambient air temperature is 30 -C. Calculate the temperature of the plate in deg F under equilibrium conditions.
On a winter’s day the outside temperature of a 17-in thick concrete wall is −29°F, the wall is 15 ft long and 9 ft high. How many BTUs are required to keep the inside of the wall at 69°F? Assume the thermal conductivity of the wall is 0.8 BTU/h ft°F.
3. A lumped system with a volume of 0.003 m³ and a surface area of 0.08 m² is made of a material with density of 3800 kg/m³, thermal conductivity of 300 W/m K, and specific heat of 200 J/kg K. If the system is exposed to a convection environment with h = 60 W/m2 K, what is the approximate time it will take for this system to reach equilibrium with the environment? Express your answer in minutes.
Consider a person standing in a room kept at 22°C at all times. Your house It has been observed that the inner surfaces of the walls, floor and ceiling are at an average temperature of 15°C. If this person's exposed surface area is 1.4 m2 and if the average external surface temperature is 30°C, this person and the surrounding surfaces Determine the radiation and heat transfer rate between One's emissivity, the Stefan-Boltzmann constant a=5,67x10 -8 W/m 2 K 4
1. A 1000-W iron is left on the iron board with its base exposed to the air at 20°C. The convection heat transfer coefficient between the base surface and the surrounding air is 35 W/m². °C. If the base has an emissivity of 0.6 and a surface area of 0.02 m², determine the temperature of the base of the iron. 2. The inner and outer surfaces of a 5-m x 6-m brick wall of thickness 30 cm and thermal conductivity 0.69 W/m °C are maintained at temperatures of 20°C and 5°C, respectively. Determine the rate of heat transfer through the wall, in W.
4: Consider a person standing in a room maintained at 20°C at all times. The inner surfaces of the walls, floors, and ceiling of the house are observed to be at an average temperature of 12°C in winter and 23°C in summer. Determine the rates of radiation heat transfer between this person and the surrounding surfaces in both summer and winter if the exposed surface area, emissivity, and the average outer surface temperature of the person are 1.6 m2, 0.95, and 32°C, respectively.
A 0.035-mm-diameter stainless steel wire having k = 16 W/m · ◦C is connected to two electrodes. The length of the wire is 85 cm and it is exposed to a convection environment at 20◦C with h =500 W/m2 · ◦C. A voltage is impressed on the wire that produces temperatures at each electrode of 200◦C. Determine the total heat lost by the wire.
A 0.025-mm-diameter stainless steel wire having K =16 W/m • C is connected to two electrodes. The length of the wire is 80 cm and it is exposed to a convection environment at 20 •C with h = 500 W/m2 • •C. A voltage is impressed on the wire that produces temperatures at each electrode of 200 -C. Determine the total heat lost by the wire in cal/hr.
The outer surface of the grill hood shown in the figure below is at T = 47°C and the emissivity is 0.93. The heat transfer coefficient for convection between the hood and the surroundings at 27°C is h = 10 W/m².K. To=27°C,h -T₁, e=0.93 Determine the net rate of heat transfer between the grill hood and the surroundings by convection and radiation, in kW per m² of surface area.
A glass window with an area of 0.625 m² is installed in the wooden outside wall of a room. The wall dimensions are 25 x 3.05 m. The wood has a k of 0.151W/m.K and is 3.05 cm thick. The glass has a k of 0.692W/m.K and is 5.0 mm thick. The temperature of the inside room is 27°C and outside air temperature is 268K. Find the heat loss through wooden wall and the glass window ?